Digital Projection Hl12000hd, Hl10000hd Users Manual

E-51
Store ............ Enables you to store the currently projected sig-
nal.
NOTE: This can be done by pressing CTL and ENTRY LIST buttons.
Cut ............... Enables you to remove a selected signal from
the list and place it on the clipboard in the Pro-
jector.
Copy ............ Enables you to copy a selected signal from the
list and place it on the clipboard in the Projec-
tor.
Paste ........... Enables you to paste the signal placed on the
clipboard to any other line of the list. To do this,
select...

E-52
DigiView - SweetVision
The SweetVision feature provides improvement of contrast us-
ing a proprietary detail enhancement technology.
This is valid when there is signal input to MM-VIDEO and to the
MM-SDI (option).
NOTE: This feature is not available for 480p, 576p and HDTV signals.
Te lecine
Use 3:2 pull down correction to eliminate jitter and artifacts in
video.
Auto ............. For film source such as a DVD player
2:2 Off ......... The telecine signal detection and compensation
will be performed...

E-53
Synchronize
Sets display vertical frequency to be synchronized with input sig-
nal.  RGB signals only.
OFF ............. Display vertical frequency - is independent of in-
put signal - displayed picture is fixed at 60Hz.
ON ............... Display vertical frequency - is synchronised
with input signal.
Frequency range of synchronization is from
24Hz to 60Hz. If vertical frequency is outside of
the range 24Hz to 60Hz, set “OFF”.
When a horizontal line (the edge of picture) is
displayed on the screen,...

E-54
Input Position
This adjusts the position of the video that is input to the resolu-
tion conversion processing section.
It is the same function as “Input Position” within the “Edge Blend-
ing” screen.
Output Position
This adjusts the image output position on the display panel.  If
the image is displayed smaller than the allowable image area of
the projector (such as native resolution), this output can be ad-
justed as needed.
Option Adjust
Clamp Timing
According to the signal, this function sets the...

E-55
6. Using On-Screen Menu
NOTE:
•To enable the Lens Memory feature, select [Ref. Adjust] → [Ref. Lens Memory]
and place a check mark next to “Yes” for [Use Point on Signal Change?].
•To store adjusted values common to all the input sources, use the Ref. Lens
Memory. See page E-56.
Signal Type
Select either the RGB signal type or the Component signal type.
RGB ............ RGB signal
Component .. Component signals such as Y/Cb/Cr, Y/Pb/Pr
NOTE: This feature is available on RGB only. If you do not get a...

E-56
4. Press the ENTER button.
5. Use the SELECT 
GHFE button to move the projected image frame as
shown on the example.
6. Press the ENTER button.
6. Using On-Screen Menu
•The indicated adjustment ranges are following;
Horizontal direction ....± 30 degrees (maximum)
Vertical direction ........± 40 degrees (maximum)
• When horizontal and vertical adjustment is occured at a time, the adjustment
range will be narrower.
•Curved Line Warp Correction
Only linear screen warp is adjusted by Cornerstone...

E-57
NOTE: This option is only available when
Yes is selected for Use Point on Signal
Change?.
Even if “CANCEL” is executed, changes to “Set Reference Point”,
“Use Reference Point” and “Return to Factory Default” will not be
canceled.
*See Tips on Adjusting Focus on page E-31 for more information.
NOTE:
•Adjusted values in Ref. Lens Memory will not be returned to default by using the
Factory Default.
•To store adjusted values for each input source, use the Lens Memory.
NOTE: In the Link mode the Lens...

E-58
(4) Perform blending correction for the Right hand edge of the  Left
projector.
Use E to adjust the blend of the left projector and press ENTER.
• To change the number of pixels in the superimposed area, input the
same value as used in (3) above using the Remote Control numeric
buttons, then press ENTER.
This value can also be adjusted using F
 or E, on the remote control.
- Adjusting the lens shift
Fine position adjustment of the images projected is allowed. This
adjustment is saved as Ref. Adjust...

E-59
6. Using On-Screen Menu
(3) Adjust the settings in (1) and (2) so that images on the screen are
superimposed.
(4) Select “Adjust (Source)” → “Image Options”  → “Blanking” of the
Advanced Menu and hide the left and right unrequired portions of the
screen as required.
- Checking the “Black Label Only” check box
If images are displayed by two or more projectors together, blending
correction is necessary.  On the other hand, if images are separately
displayed by each projector, blending correction must...

E-60
Projector Options
Menu
[Page 1]
Selecting Menu Language [Language]
You can choose one of seven languages for on-screen instruc-
tions. The options are: English, German, French, Italian, Span-
ish, Swedish and Japanese.
Selecting Menu Mode [Menu Mode]
This feature allows you to select 4 menu modes: Advanced,
Custom, Basic and Service Menu.
Advanced Menu ...... This is the menu that contains all the
available menus and commands.
Basic  Menu ............. This is the basic menu that contains mini-
mum...