Digital Projection Hl12000hd, Hl10000hd Users Manual

E-11
2 Features
•HDTV support, suited to 3D movement and telecine, with
I/P conversion
I/P conversion processing using an interpolation circuit suited
to 3D movement that supports HDTV and SDTV signal input
as well as telecine signals permits reproduction of images hav-
ing impressive definition.
•Full 10 bit image processing circuit
The image processing circuit features 10 bits for each color.
As a result, there is complete 10 bit processing when the sig-
nal is input from the optional SDI interface...

E-12
1. Introduction
3 Getting to Know Your Projector
Ventilation (outlet)
Control panel
(See page E-13)
Ventilation (inlet) Control terminals
(See page E-14)
Main power switch
(See page E-30)
Power cable Input terminals
(See page E-15)
Remote sensor
Lens (optional)
Frame
Remote sensor
Tilt Adjustment Knob
Roll Adjustment Knob
PAN Adjustment Knob
NOTE: The frame is not included on HL10000HD. 

E-13
Control Panel
1. LCD ScreenThe liquid crystal display screen shows the condition or the
error message of the Projector.
2. FOCUS (+/-) ButtonWhile pressing and holding CTL Button, pressing this button
allows you to adjust the lens focus.
3. ZOOM (+/-) ButtonWhile pressing and holding CTL Button, pressing this button
allows you to zoom the lens in and out.
4. LENS SHIFT GHFEWhile pressing and holding CTL Button, pressing this button
allows you to adjust the lens offset by shifting the projected
image...

E-14
Control Terminals
1. Introduction
1. USB Port (USB B)(Type B)
Connect this port to the USB port (type A) of your PC using a
USB cable.
When USB cable is connected to this port, ferrite core, which
attached to this equipment, is assembled to USB cable (near
side of this equipment).
2. USB Port (USB A)(Type A)
When working on “menu”, commercially available USB mouse
is connected and used. See page E-45.
3. REMOTE IN 1 (Mini Jack)
Wired remote control input.  See Page E-20.
Ferrite core supplied should...

E-15
1. Introduction
Input Terminals
(3)(2)(1)
1. SLOT 1 (MM-VIDEO)
MM-VIDEO interface board is standard equipment.2. SLOT 2 (MM-RGB)
MM-RGB interface board is standard equipment.
(1) CVBS Input Connector (BNC Type)
Use a 75 Ω coaxial cable and connect it to the Composite
Video output connector of a DVD player, or to other equip-
ment.
(2) S-VIDEO Input Connectors (2 BNC Type)
Use a 75 Ω coaxial cable (2-conductor type) and connect it to
the S-Video output connector of a DVD player, or to other equip-...

E-16
Input Board (Options)
MM-DVI Interface Board
The DVI digital signal input board is available as an option.MM-SDI Interface Board
The SDI signal input board is available as an option.
(1) STATUS Indicator
Steady green light ... Shows that a signal is present.
Steady red light ....... Shows that there is no signal or an error
occurs.
(2) SDI 1 and SDI 2 Input Connectors (BNC type)
Use a 75 Ω coaxial cable and connect it to a video server or
video equipment.
(3) MONITOR OUT Connector (BNC type)
Outputs...

E-17
1. Introduction
4 Remote Control Features
1. POWER ON
Press and hold this button for a minimum of 1 second to turn
on the Projector when the main power is supplied and the Pro-
jector is in standby mode.
2. POWER OFF
Press and hold this button for a minimum of 1 second to turn
off the Projector.
3. Source / Input
Press to select input or to name a signal.
1Selects the input connector of Slot 1 (MM-VIDEO at time of factory
shipping).
Each press of “1” button switches the input connector one step in...

E-18
1. Introduction
11. ENTRY LIST
Press to display the Entry List screen.
Pressing and holding CTL and then ENTRY LIST buttons si-
multaneously, enters a signal in the Entry List.
12. HELP
Provides online help.
13. INFO
Displays the Source Information or Projector Information
window. This button toggles between these two windows.
14. PIXEL
Displays the Position/Clock screen to adjust the clock and
phase.
15. POSITION
Press to display the Position screen; press again to display
the Blanking screen....

E-19
1. Introduction
Remote Control Precautions
•The remote control system may not function when direct sunlight or
strong illumination strikes the remote control sensor of the main unit, or
when there is an obstacle in the path.
•When remote control buttons are pressed and held, Projector’s func-
tion keys may not operate.
•Do not subject to strong shock.
•Do not allow water or other liquid to splash on the remote control. If the
remote control gets wet, wipe it dry immediately.
•Avoid exposure to heat...

E-20
REMOTE
IN 1
Using the Remote Control in Wired Operation
Connect one end of the supplied remote cable to the REMOTE IN 1
mini jack and the other end to the remote jack on the remote control.
NOTE:
Do not use this jack for anything other than intended use.
For HL12000HD and HL10000HD, conect a ferrite core supplied to the projector end of
the remote cntrol cable.  For fitting instructions for Ferrite cores, see page 28.
Remote cable (supplied)
1. Introduction