Digital Projection Hl12000hd, Hl10000hd Users Manual

E-41
5. Setting Up for Double Stacking in Link Mode
1-6. Control Cable ConnectionExample of Remote Controllers Control
Remote controller and master projector’s remote controller input 1 port (REMOTE1 IN 1 )are connected by remote cable. Master
projector’s remote output port (REMOTE OUT) and slave projector’s remote controller input 1 port (REMOTE IN 1) are connected by
remote cable.
NOTE:
•When ID is not setup for the projector and remote controller, two projectors are controlled at the same time with...

E-42
5. Setting Up for Double Stacking in Link Mode
2 Adjusting and Registering Signals to Be
Projected
2-1. Making Adjustments to the Master Projector
2-1-1. Display a desired input signal on the master projector.
2-1-2. Make adjustment to the signal, then save (register) ad-
justments on the master projector by pressing and holding
CTL and pressing ENTRY LIST button on the remote con-
trol.
2-1-3. Repeat steps 2-1-1 and 2-1-2 for all signals you want
to project.
Display all the signals you registered...

E-43
6
Using On-Screen Menu
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
1 Basic Menu Operation ............................. E-44
2 List of Direct Button Combinations .......... E-45
3 Using the USB Mouse ............................. E-45
4 Menu Tree ............................................... E-46
5 Menu Descriptions & Functions ............... E-50
Source Select .......................................... E-50
Adjust (Source) ....................................... E-51
Picture...

E-44
ENTER
ENTER
ENTER
MENU/ADDRESS
1 Basic Menu Operation
Using the Menus
1. Press the MENU button on the remote control or the Projector cabinet
to display the Basic, Advanced or Custom Menu.
Customizing the Menu
The Custom menu can be customized to meet your requirements.
Selecting a menu item from the Custom Menu Edit list, allows
you to custom tailor the menu items to your needs.
1. Select Custom Menu Edit to display the Custom Menu Edit screen.
2. Use the SELECT 
G or H buttons to highlight your...

E-45
2 List of Direct Button Combinations
CTL+  Input  (1-10) Switches to any selected signal found in the Entry List.
To enable this combination, you must first assign specific remote buttons
for direct input selection in the Entry Edit window.
CTL+  ENTER (While  displaying  Entry  list) Displays the selected signal.
CTL+  CANCEL Returns  to  the previous menu without closing the slidebar or dialog.
CTL+  UNDO Clears all menus or adjustment/setting screens. All adjustments are saved
automatically.
CTL+...

E-46
4 Menu Tree
6. Using On-Screen Menu
NOTE: The shaded item indicates the default setting.
S1: Video
S1: S-Video
S1: Component
S2: RGB
S3: None
S4: None
Entry List
Load / Store / Cut / Copy / Paste / Edit / All Delete
Brightness / Contrast / Saturation / Colour / Hue /Sharpness /Setup Level
Noise Reduction Off / Low / Medium / High
Colour Matrix Select Colour Matrix HDTV / SDTV
Select Colour Matrix Type B-Y/R-Y / U/V / Cb/Cr /
Pb/Pr / IVX
Y/C Delay -15 to 15
YTR Adjustment 0 to 31
CTR Adjustment 0 to...

E-47
6. Using On-Screen Menu
NOTE: The shaded item indicates the default setting.
3D Reform
Screen
Ref. Lens Memory
Edge Blending
Lamp Mode
All Data (Including Entry List) / Current Signal
Menu
Setup
Page 1
Page 2
Page 3
Page 1
Page 2
Page 3
Page 4
Advanced Menu
Source Select
Adjust (Source)
Ref. Adjust
Factory Default
Projector Options
Tools
Help
Test PatternCornerstone 8 direction / close
Keystone decrease ¨Æ increase
(When MM-WARP (optional) is inserted, horizontal / vertical)
Screen Type1.25:1(5:4) /...

E-48
6. Using On-Screen Menu
NOTE: The shaded item indicates the default setting.
LAN Mode
Image Mode
Password
Security
LAN Card Build-in / PC Card
Projector Name
IP Address
Subnet Mask
Gateway
MAC Address
Advanced IP Address Automatic / Manual
IP Address
Subnet Mask
Gateway
DNS Configuration
Domain Name
Network TypeModeInfrastructure /
802.11 Ad Hoc /
Ad Hoc
SSID
Channel 1 to 14
TX Rate
Automatic / 11M /
5.5M / 2M / 1M /
1M-2M-Automatic
WEP WEPDisable / 64 bit /
128 bit
Key Select Key 1 to 4
Key 1 to 4...

E-49
6. Using On-Screen Menu
Contents
Source Information
Projector Information
Page 1 Source Name / Input Terminal / Entry No. /
Horizontal Frequency / Vertical Frequency / Sync Polarity
Page 2 Signal Type / Video Type / Sync Type / Interlace / Direct Key
Page 1 Serial Number / Remaining Lamp Time / Lamp Hour Meter /
Projector Usage / Projector ID
Page 2 Version (BIOS / Firmware / Data / FPGA)
Page 3 Version (Formatter Red)
(Boot App / Config / Degamma / Main App / Sequences)
Page 4 Version (Formatter...

E-50
Entering Alphanumeric Characters by Using the Menu
Alphabet or numeric characters are used for your IP address or
Projector name. To enter IP Address or Projector name, use the
software keyboard.
For using the software keyboard, see page E-90.
Entering Alphanumeric Characters by Using the Remote
Control Numeric Buttons
Input alphanumeric characters by selecting one character at a
time with the numeric (Source/Input) buttons 1through 10(0) and
by moving the cursor with the SELECT E button. After...