Digital Projection Highlite Cine 260 Hb, Hc, Highlite 1080p 330 User Manual

Rev B   July 2011 Page 4.29
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Blue Only
This is useful for color-calibrating the projector or other video compon\
ents.
Use the 
 and  keys to select from:
On  only the blue signal is displayed - green and red are turned off
Off    all three signals - red, green and blue - are displayed
Test Patterns
Use the  and  keys to select from:
Test Pattern Off
White
Black
Red
Green
Blue
Cyan
Magenta
Yellow
Chequerboard...

Page 4.30 Rev B   July 2011
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 

Rev B   July 2011  Page 5.1
5. Maintenance
Contents
Changing the lamp module ........................................................................\
......................................5.2
Cleaning the fans ........................................................................\
........................................................5.3
Cleaning or replacing the air filter ........................................................................\
..........................5.4 

Page 5.2 Rev B   July 2011
5. Maintenance Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Changing the lamp module
Turn the power OFF and allow the lamp to cool for 5 minutes.
Unscrew the captive finger screw securing the lamp door, and remove the door.
Unscrew the two cross-head screws securing the lamp module to the projec\
tor
Lift the wire handle up and use it to pull out the lamp module.
Fit a new lamp module, pushing it firmly into place.
Tighten the two cross-head screws.
Locate the...

Rev B   July 2011 Page 5.3
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 5. Maintenance
Cleaning the fans
Turn the power OFF and wait until the fans stop.
Use a vacuum cleaner to clean the inlet and outlet fans, as shown below.
•
•
Notes
 
Always switch the projector 
OFF before cleaning the fans.
 Always allow the lamp to cool 
for 5 minutes before: 
- disconnecting the power  
- moving the projector  
- changing the lamp  
- cleaning the fans and filter
  The fans should be cleaned...

Page 5.4 Rev B   July 2011
5. Maintenance Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Cleaning or replacing the air filter
Turn the power OFF and allow the lamp to cool for 5 minutes.
Unscrew the two cross-head screws securing the filter cover to the proje\
ctor
Remove the cover and the filter.
Clean the filter using clean water, or replace it with a new filter.
Allow the filter to dry before reuse.
Replace the filter, pushing it firmly into place.
Refit the filter cover.
•
•
•
•
•
•
•...

Rev B   July 2011  Page 6.1
6. Appendix
Contents
Troubleshooting ........................................................................\
..........................................................6.2
Error codes ........................................................................\
..............................................................6.4
Dimensions ........................................................................\
..................................................................6.5...

Page 6.2 Rev B   July 2011
6. Appendix Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Troubleshooting
problempossible solutions
The red ISSUE indicator is illuminated 
continuously or flashing. Check the Error codes detailed on the next page.
The projector will not power up. Check that the mains plug is plugged in and that the mains supply is swi\
tched on.
Check that the lamp door is closed properly.
Check any external fuses or breakers.
The projector will not power up shortly 
after being...

Rev B   July 2011 Page 6.3
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 6. Appendix
problempossible solutions
Image is split or otherwise scrambled.Check that the image source is not set to progressive scan.
Image is blurred. Check that the lens is focussed correctly.
Image is too bright, and lacks 
definition in the bright areas. Decrease the contrast setting.
See section 4. Controlling the projector, Using the control keys and Main 
menu
Image appears ‘washed out’ and is too 
bright in...

Page 6.4 Rev B   July 2011
6. Appendix Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Error codes
If the projector detects an error, the red Issue indicator will flash, as shown in the 
chart below.
For example, if the lamp door is left open, the red indicator will flash\
 twice followed 
by a pause, then the sequence will repeat until the error condition is c\
orrected.
Notes