Digital Projection Highlite Cine 260 Hb, Hc, Highlite 1080p 330 User Manual

Rev B   July 2011 Page 3.3
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 3. Getting Started
Selecting an input signal or test pattern
Input
Connect an video source to the projector. The signal should be automatically 
detected by the projector, and should be displayed within a two or three 
seconds.
If more than one signal is connected to the projector, then select which signal 
is to be displayed, using the 
 to   buttons on the remote control, or 
by pressing the SOURCE button on the...

Page 3.4 Rev B   July 2011
3. Getting Started Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Adjusting the projected image
Aspect ratio
Press  on the remote control until the image is displayed in the corect aspect\
 
ratio.
Image quality settings
Press any of the following keys on the remote control, followed by  and , to 
adjust these image quality settings:
 Brightness   
Contrast   
Sharpness   
•
•
Notes
  For more detailed information 
about:
  - using all the control keys 
on the...

Rev B   July 2011  Page 4.1
4. Controlling the projector
Contents
Adjusting the lens........................................................................\
.......................................................3.3
Example - Lens Shift control: ........................................................................\
.....................................3.3
Overview ........................................................................\...

Page 4.2 Rev B   July 2011
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Advanced menu ........................................................................\
........................................................4.14
Colour Space ........................................................................\
.........................................................4.14
Video Standard ........................................................................\...

Rev B   July 2011 Page 4.3
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Overview
Controlling the projector
The projector can be controlled from:
the remote control
the projector control panel
the RS232 input
For more information about controlling the projector using the RS232 inp\
ut, see 
Remote communications protocol  in 
section 6. Appendix.
For information about how to connect the projector, see Connecting the 
projector in section 2. Installation, and...

Page 4.4 Rev B   July 2011
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
The control panel
The projector control panel is designed to be read from the front or rea\
r of the 
projector, for ease of use.
The menu navigation keys are similar to those on the remote control, and\
 are 
described in detail in  Using the menus, later in this section.
POWER 
  Press this once to switch the projector ON or twice to switch it to 
STANDBY mode.
SOURCE
  Press this...

Rev B   July 2011 Page 4.5
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
The remote control
Layout
Timeout
There is a 5 second timeout for the  control keys at the bottom of the remote control:
- after 5 seconds, if no adjustment has been made, the indicator will go\
 out and 
the adjustment key must be pressed again.
- to end the adjustment before 5 seconds has elapsed, press a different 
adjustment key, or press the key again.
There is a 30 second timeout for...

Page 4.6 Rev B   July 2011
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
 For more information about the 
sources programmed into the 
SOURCE keys, see Control 
menu later in this section, 
Using the menus. 
 For more information about 
the Aspect ratio settings, 
see Screen requirements  in 
section 2. Installation .
 For more information about 
the settings programmed into 
the USER MEMORY keys, 
see Control menu later in this 
section.
  Note: User...

Rev B   July 2011 Page 4.7
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Image quality settings
Press any of the following keys on the remote control, followed by  and , to 
adjust these image quality settings:
 Brightness   
Contrast   
Sharpness   
Gamma   
Overscan   
Noise reduction 
Colour temperature 
Example - Brightness screen control:
Test pattern
Press the  key repeatedly to cycle through the Test patterns, in the 
following order:
White, Black, Red,...

Page 4.8 Rev B   July 2011
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 There is a 30 second timeout 
for the menu navigation keys. If 
a menu times out, simply press 
the Menu key again.
 The SELECT key on the 
projector control panel has 
exactly the same funtion as 
the ENTER key on the remote 
control.
 To exit from the menus 
completely, you may...