Digital Projection Highlite Cine 260 Hb, Hc, Highlite 1080p 330 User Manual

Rev B   July 2011 Page 2.13
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 2. Installation
Notes
 Make sure the rear lens cap is 
removed, before fitting the lens.
 Be careful not to scratch 
the lens surfaces. If you do 
accidentally touch a lens, then 
clean the surface using a lens 
paper.
Still holding down the tab, push the lens in firmly as far as it will go\
.
Rotate the lens clockwise as far as it will go.
Release the lens holder tab.
Position the front cover as shown below, hold it...

Page 2.14 Rev B   July 2011
2. Installation Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Shifting the image
Ideally, the projector should be positioned perpendicular to the screen.
The normal position for the projector is at the centre of the screen. Ho\
wever, with 
the zoom lenses, you can set the projector above or below the centre, or\
 to one 
side, and adjust the image using the  Lens shift controls on the top of the projector 
to maintain a geometrically correct image.
The maximum...

Rev B   July 2011 Page 2.15
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 2. Installation
Mounting the projector
The four adjustable feet under the chassis allow the projector to be low\
ered onto a 
flat surface without any danger of hands being trapped between the botto\
m frame 
and the surface.
Ceiling mounting
The projector is designed to be used on a flat surface, but it can be su\
spended 
from a ceiling. Four M4 mounting holes with a 0.7mm pitch are provided u\
nder the 
projector...

Page 2.16 Rev B   July 2011
2. Installation Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
 For more detailed information 
about using the menus, see 
section 4. Controlling the 
projector.
 Do not try to stack more than 
three projectors.
 When stacking projectors, 
the stack MUST be vertical, to 
ensure that the stresses are 
distributed to all four chassis 
corners.
 Make sure that the surface, 
ceiling or rigging that is 
to support the projector is 
capable of supporting the...

Rev B   July 2011 Page 2.17
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 2. Installation
Notes
 For more information on 
selecting an input source, see 
section 4. Overview, Using 
the control keys, and Using 
the menus.
 
  For more information about pin 
connections and control codes 
see section 6. Appendix.
Connecting the projector
Signal Inputs
The following inputs are available:
HDMI 1 & 2
  HDCP-compliant digital video inputs from HDMI or DVI sources.
RGB  15 pin D-type VGA style...

Page 2.18 Rev B   July 2011
2. Installation Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Input connection examples, continued 

Rev B   July 2011 Page 2.19
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 2. Installation
Notes
 
 For more information about pin 
connections and control codes 
see section 6. Appendix.
 For information how to enable 
and disable the remote control, 
see Control Menu  in section 
4. Controlling the projector , 
and Remote communications 
protocol , in section 6. 
Appendix.
  For more information how to 
switch between RS232 and 
LAN control see  Control Menu 
in section 4. Controlling 
the...

Page 2.20 Rev B   July 2011
2. Installation Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Power connection
Push the cable lock to the left, plug the mains connector in firmly, then push the 
lock back to secure the cable.
Switch on at the switch next to the power connector.
•
•
Notes
 
Use only the power cable 
provided.
 Ensure that the power 
outlet includes a Ground 
connection, as this 
equipment MUST be earthed.
 Handle the power cable 
carefully and avoid sharp 
bends. Do not use a...

Rev B   July 2011  Page 3.1
3. Getting Started
Contents
Positioning the screen and projector ........................................................................\
....................3.2
Switching the projector on ........................................................................\
.......................................3.2
Inserting batteries into the remote control ........................................................................\
...........3.2
Selecting an input signal or test pattern...

Page 3.2 Rev B   July 2011
3. Getting Started Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Switching the projector on
Connect the power cable between the mains supply and the projector. Switch on 
at the switch next to the power connector.
Wait until the self-test has completed and the standby indicator on the p\
rojector 
control panel shows amber. The lamp will be off and the projector will be in 
STANDBY mode.
Press POWER ON 
 on the remote control or POWER  on the projector 
control...