Digital Projection Highlite 4000dsx User Manual

							20 - MUTE PICTURE
Press to turn off the picture for a short period of time. Press again to restore the pic-
ture. Pressing and holding CTL, then pressing this button closes the light shutter
such that no light is emitted through the projection lens.
21 - KEYSTONE (R)
Press to display the Keystone Correction screen.
22 - AMPLITUDE (G)
Service personnel only.
23 - ENTRY LIST (B)
Press to display the Entry List screen.
24 - FOCUS (+/-)
While pressing and holding CTL, pressing this button allows you to adjust the lens
focus.
25 - MAGNIFY/ZOOM (+/-)
Magnify the size of a target portion.
While pressing and holding CTL, pressing this button allows you to zoom the lens
in and out.
26 - CTL
Used in conjunction with other buttons, similar to a shift key on a computer key-
board.
C—5
0verview
OVERVIEW
LBV00072; Revision A - 25/09/2001 
						

							27 - INFRARED TRANSMITTER
Direct the remote control toward the remote sensor on the projector cabinet.
28 - REMOTE JACK
Connect your remote control cable here for wired operation.
C—6
Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001
OFF
+-
PICTUREADJUSTABC DEFGHI
JKL MNO PQR
STU
,.VWXWHITE BAL.IMAGE
ON POWER
MENU
ENTER
123
456
7
08ADDRESS
PROJECTOR
BS
28
27 
						

							Direct Key Combinations
The CTL button can be used in conjunction with other remote control buttons to
provide alternative functions. A list of these combinations is provided below.
KEY COMBINATION ACTION
CTL + INPUT (1-10) Switches to selected signal found in the Entry List.
To enable this combination, you must first assign 
specific remote keys for direct input selection in 
the Entry Edit window.
CTL + ENTER  Displays the Entry Edit Command Window. Only
available while displaying the Entry List window.
CTL + MUTE PICTURE (SHUTTER) Blocks all projector light output.
CTL + CANCEL Returns to previous menu without closing the 
slidebar or dialogue box.
CTL + UNDO Clears all menus or adjustment/setting screens. 
Adjustments & settings are saved automatically.
CTL + Cursor Button Moves the slidebar or dialogue box horizontally 
or vertically.
CTL + Cursor Button (while using zoom)Displays the magnifying glass icon.
CTL + Left Cursor (BS) Deletes one letter or numeral in the entry screen.
CTL + TEST Displays the Passcode Entry screen.
CTL + MENU (ADDRESS) Displays the Remote ID Entry window.
CTL + IMAGE (PROJECTOR) Sequentially selects the Projector Options sub 
menus.
CTL + POSITION (LENS) Displays the Lens Shift control window.
CTL + KEYSTONE (R) Turns on Red. Only available when viewing Test 
Patterns.
CTL + AMPLITUDE (G) Turns on Green. Only available when viewing 
Test Patterns.
CTL + ENTRY LIST (B) Turns on Blue. Only available when viewing Test 
Patterns.
CTL + MAGNIFY (ZOOM) Zooms the lens in and out.
CTL + (FOCUS) Adjusts the lens focus.
CTL + INFO Saves Lens Zoom and Focus position.
C—7
0verview
OVERVIEW
LBV00072; Revision A - 25/09/2001 
						

							The Basic/Custom menu can be customised to meet your requirements.
Select ‘Projector Options’ - ‘Menu’ - ‘Page1’ - ‘Basic/Custom Menu Edit’ to dis-
play the menu editing screen.
Highlight your desired selection and press the ENTER button to place a check mark
next to the option. 
If you select an item with a solid triangle and press the ENTER button all submenu
items will also be selected.
You can press the ENTER button again to clear a check mark.
Up to 12 main items (not including submenu items) can be selected for display.
To finalise your selection navigate to the OK button and press the ENTER button.
You will then be asked to confirm the changes.
All items not selected can still be accessed by selecting ‘To Advanced Menu’ item
in the Main Menu.  
C—8
Overview
Basic/Custom Menu
OPERATION
LBV00072; Revision A - 25/09/2001 
						

							Slide Bar
Menu windows or dialog box typically have the following elements:
Title bar- Indicates the menu title.
Highlight- Indicates the selected menu or item.
Solid triangle- Indicates further choices are available. A highlighted triangle 
indicates the item is active.
C—9
Overview
Menu System Overview
OPERATION
LBV00072; Revision A - 25/09/2001
Radio Button
Title Bar
Tab
Highlight
Check Box
Cancel Button
Solid Triangle
OK Button 
						

							-
Tab- Indicates a group of features in a dialog box. Selecting any tab brings its page
to the front.
Radio button- Use this round button to select an option in a dialog box.
Check box- Place a checkmark in the square box to turn the option On.
Slide bar- Indicates settings or the direction of adjustment.
OK button- Press to confirm your setting. You will return to the previous menu.
Cancel button- Press to cancel your setting. You will return to the previous menu.
Navigating the Menu System
Press the MENU button on the remote control to display the Main Menu. Next, use
the up and down cursor buttons on the remote control to select the required sub
menu and press ENTER.
Using the up and down cursor buttons to select the item to be modified from the sub
menu and press ENTER to display the adjustment screen or dialog box.
A right-oriented delta symbol     in the menu structure indicates that further
choices are available by pressing the right cursor button.
Adjust the level or turn the selected item on or off using left or right cursor keys on
the remote control. The on-screen slide bar will show you the amount of increase or
decrease.
To exit, press CANCEL on the remote control.
The change is stored automatically when the on-screen display disappears, the
projector goes into standby mode or one input is switched to another.
C—10
Overview
OPERATION
LBV00072; Revision A - 25/09/2001
- 
						

							Menu Structure
C—11
Overview
OPERATION
LBV00072; Revision A - 25/09/2001
0 – 100
NTSC, Graphics NTSC, PAL/SECAM2.8,
PAL/SECAM, Natural 1/Natural 2 
Advanced Menu
Source Select
Adjust (Source)
Ref Adj
Factory Default
Projector Options
Help
Test Pattern
RGB1
RGB2
RGB3
Component (YCbCr)
Video1
Video2
S-Video1
S-Video2
RGB (DIGITAL)
SDI
Entry List
Switcher
Entry List When Switcher Control is
turned on:
Stand aloneBrightness
Contrast
Saturation
Color
Hue
Sharpness
V-Aperture
Gamma Correction
Color Temperature
Brightness
Contrast
Signal Level
Pixel Adjust
Position
Aspect Ratio
Resolution
Overscan
Video Filter
Blanking
Noise Reduction
Color Matrix
Y/C Deray
Telecine
Motion Select
Motion Level
YTR Adjustment
CTR Adjustment
Clamp Timing
Sync Protection
VD Delay
Gain
Volume
Reference / Custom
RGB / Component Picture
White Balance
Image
Video Adj
Option Adj
Lens Memory
Signal Type
Switcher
Brightness R/G/B
Contrast R/G/B
Clock / Phase
Horizontal / Vertical
Input Signal 1.25:1 / 1.33:1 / 1.78:1 / 1.85:1 / 2.35:1
Display Area 1.25:1 / 1.33:1 / 1.78:1 / 1.85:1 / 2.35:1
Auto / Native
0% / 5% / 10% / 25%
On / Off  Top / Bottom
Luminance  Off / Low / Medium / High
Chrominance  Off / Low / Medium / High
Select Color Matrix  HDTV / SDTV
Delect Color Matrix Type  B-Y/R-Y, U/V, Cb/Cr
Pb/Pr, IVX
Auto / Off
Still / Adaptive
Auto / Tri-Sync / Front Porch / Adjust
Red / Green / Blue 
						

							C—12
Overview
OPERATION
LBV00072; Revision A - 25/09/2001
SX6000: Auto / High-Bright / Variable   SX4000: Auto / VariableAdvanced Menu
Source Select
Adjust (Source)
Ref Adj
Factory Default
Projector Options
Help
Test Pattern
All Data / Current SignalIncluding Entry List Keystone
Lamp
Ref. White Bal.
Contents
Source Information
Projector Information
Lamp Mode
Lamp Output
Brightness R/G/B, Contrast R/G/B
Standalone / Master / Slave
Standalone / SW 1 Level / SW 2 Level
Contents
Cross Hatch, Gray Bars
Black Raster, Gray Raster
White Raster
Red / Green / Blue
Page 1
Page 2
Page 3Source Name / Input Terminal / Entry No. / Horizontal Frequency /
Vertical Frequency / Sync Polarity
Signal Type / Video Type / Sync Type / Interlace / Resolution / Direct Key
Aspect Ratio (I) / Aspect Ratio (D) / Gamma Correction / Noise Reduction (L) / 
Noise Reduction (C) / Color Matrix / Matrix Type
Page 1
Page 2Menu Mode (Basic/Custom Menu, Advanced Menu, Service Menu)
Basic/Custom Menu Edit
Language (English / German / French / Italian / Spanish / Swedish / Japanese)
Menu Display Time (Manual / Auto 5 sec / Auto 10 sec / Auto 30 sec)
Display Select (Date, Time, Input Terminal, Source Name, Projector ID, On/Off)
Date Format
(MM/DD/YYYY, MM/DD/YYYY ddd, DD/MM/YYYY, DD/MM/YYYY ddd
YYYY/MM/DD, YYYY/MM/DD ddd, Month DD, YYYY, Month DD, YYYY ddd)
Date, Time Preset
On / Off Timer
Sleep Timer
Timer
Menu
Setup
Link Mode
Switcher Control
Execute Switch (Active / Inactive)
Edit
Preset Time (Off / 0:30 / 1:00 / 1:30 / 2:00)
Page 1
Page 2
Page 3
Page 4
Page 5Orientation (Desktop Front / Ceiling Rear / Desktop Rear / Ceiling Front)
Background (Blue / Black / Logo)
S-Video Mode Select (Off / S2)
Signal Select
RGB 1 (Auto / RGB / Component)
RGB 2 (Auto / RGB / Component)
Sync Termination
RGB 1 (Hi-Z / 75W)
RGB 2 (Hi-Z / 75W)
Signal Select
Video 1 (Auto / NTSC3.58 / NTSC4.43 / PAL PAL60 / SECAM)
Video 2 (Auto / NTSC3.58 / NTSC4.43 / PAL PAL60 / SECAM)
S-Video 1 (Auto / NTSC3.58 / NTSC4.43 / PAL PAL60 / SECAM)
S-Video 2 (Auto / NTSC3.58 / NTSC4.43 / PAL PAL60 / SECAM)
Switcher (Auto / NTSC3.58 / NTSC4.43 / PAL PAL60 / SECAM)
Auto Adjust (RGB Only)
Power Management
Power Off Confirmation
Keystone Save
Doubler
Lens Memory
User Name
Communication Speed (4800 / 9600 / 19200 / 38400)
Projector ID (Enable / Disable) 1 – 64
Default Source Select (Last / Select)
Standalone
(RGB1 / RGB2 / Component (YCbCr) / Video1 / Video2 / S-Video1 /
S-Video2 / RGB (DIGITAL)
SW 1 Level (Slot 1 – 10)
SW 2 Level (M-01 S-01 – M10 S-10)
Page 1
Page 2
Page 3
Page 4User Name / Serial Number / Lamp Hour Meter / Projector Usage / Projector ID
Version (BIOS / Firmware / Data / SUB-CPU)
Formatter Version (CPU / PROM / Prism)
FPGA Version (OSD / JOE)
Link Mode (Master / Slave) 
						

							Main Menu
The Main Menu provides access to sub-menus which allow you to control the 
projector and to view any system settings.
Source Select- enables selection of an input source.
Adjust (Source) - provides access to the image controls.
Ref Adj- provides access to Keystone, Lamp and Reference White settings.
Factory Default- takes you to the Factory Default options menu.
Projector Options- enables you to set projector options and other operating
options
PC Card Files- provides access to files stored on CompactFlash Card.
Help- provides on-line help.
To Advanced Menu- gives access to the advanced level menus.
C—13
System Operation
Menu Operation
OPERATION
LBV00072; Revision A - 25/09/2001 
						

							Source Select enables you to select an input source connected to the projector.
To select an input source use the up/down buttons on your remote control or the
projector cabinet to highlight the desired input type and press Enter. Available
options include: RGB1, RGB2, RGB3, Component (YCbCr), Video1, Video2, 
S-Video1, S-Video2, RGB Digital or SDI.
Alternatively Entry List may be selected which contains a list of the entry signals.
When in the Entry List window, use the up/down buttons on your remote control or
the projector cabinet to select the desired signal and press the Enter button.
When switcher control is turned on selecting Source Select will provide you with
options of selecting a Switcher input or selecting a signal from the Entry List.
C—14
System Operation
Source Select
OPERATION
LBV00072; Revision A - 25/09/2001