Home > Digital Projection > Projector > Digital Projection Highlite 4000dsx User Manual

Digital Projection Highlite 4000dsx User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Digital Projection Highlite 4000dsx User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 577 Digital Projection manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							connection should be attached to the external control equipment such as PC. The
    OUT connection provides for daisy-chaining multiple projectors and operating them
    with the same external equipment. To daisy-chain projectors, connect the IN termi-
    nal of the second projector to the OUT connection of the first projector. A third pro-
    jector would be connected to the second projector in the same manner and the pro-
    cedure would be repeated until all the projectors are connected.
    3 - REMOTE 1
    This Mini D-Sub 15 pin terminal allows external control of the projector from either
    a configured switcher or from an external control source. When the switcher is used,
    connect to the REMOTE 1 terminal on the back of the switcher.
    4 - REMOTE 2
    Two 3.5mm stereo mini jack sockets allow direct wired connection to an individual
    projector or a number of projectors. The IN connector allows direct connection of
    the remote control unit. The OUT connector is used for daisy-chaining multiple pro-
    jectors and operating them with the same remote control.
    Plugging the cable into the projector will automatically disable the infra-red remote
    receivers.
    5 - INPUT 1 (RGB1) and INPUT 2 (RGB2)
    Inputs with BNC terminals for connection of R, G, B, H and V outputs of external
    equipment such as a switcher. If using a source with combined sync output, connect
    it to the H/V terminal. The R, G, B terminals can also be used to connect component
    video outputs (Y/Cb/Cr) of external equipment.
    6 - INPUT 4 (Component (Y/Cb/Cr))
    Inputs with RCA terminals for component video outputs (Y/Cb/Cr) of external
    equipment such as DVD player.
    This input accepts component signals only.
    7 - INPUT 5 (VIDEO 1)
    BNC composite video connection for external equipment such as a VCR or laser
    disk player.
    A—9
    Overview
    OVERVIEW
    LBV00072; Revision A - 25/09/2001
    - 
    						
    							8 - INPUT 6 (VIDEO 2)
    RCA composite video connection for external equipment such as a VCR or laser
    disk player.
    9 - INPUT 7 (S-VIDEO 1)
    Two BNC connectors allow for S-Video connection for use with external equipment
    such as a VCR or laser disk player that have separate Y and C video outputs.
    10 - INPUT 8 (S-VIDEO 2)
    Mini-DIN-4pin S-video connection for external equipment such as a VCR. This
    input allows switching between S2 and S1 VIDEO input modes. See the S-Video
    Mode Select section for more information.
    RGB Digital Connectors & Optional SDI Board
    There is a compartment above the terminal board on the front of the projector for
    RGB Digital connectors and the optional SDI board. The compartment is opened by
    pushing the left side of the panel.
    A—10
    Overview
    OVERVIEW
    LBV00072; Revision A - 25/09/2001 
    						
    							11 - INPUT 9 (RGB (Digital))
    DVI-D 24 pin connectors for double or triple stacking. Use the supplied DVI-D
    cable to connect the OUTPUT terminal of the first projector to the second projec-
    tors INPUT until all the projectors are connected.
    The DVI-D cable must not exceed 5 m (16.4 feet) in length.
    These connectors can also be used to accept TMDS standard digital signal output
    from a digital ready computer. When used in this manner some 
    graphics cards may cause flickering noise on the screen. 
    The projectors support a maximum resolution of 1024x768 (4100gv and 5100gv)
    or 1280x1024 (4000sx and 6000sx).
    12 - INPUT 0 (SDI)
    BNC SDI connection for use with equipment such as commercial type digital VTR.
    Compatible with digital component signals complying with SMPTE 259M-C 
    standard.
    4000sx and 6000sx models are also compatible with digital component signals com-
    plying with SMPTE 292M standard.
    For further information on installing the optional SDI board contact your Digital
    Projection Dealer.
    A—11
    Overview
    OVERVIEW
    LBV00072; Revision A - 25/09/2001
    -
    -
    OUTPUT OUTPUT
    RGBDIGITAL
    INPUT9 INPUT 0
    SDI
    11 
    						
    							OPTIONALLY AVAILABLE SDI BOARDS
    SDI Board (all models)
    This board accepts the input of non-compressed signal sources from equipment such
    as commercial type digital VCR compatible with digital serial component signals of
    the SMPTE 259-C standard and provides a high quality image without quantisation
    noise.
    BNC cable used with the SDI connector should be Belden 8281 cable, or 3C-2V
    equivalent cable or better.
    Included in option:-
    SDI Board Shield Case
    Connector Cable (Internal) Installation Manual
    HDSDI Board (sx models only)
    This board accepts the input of non-compressed signal sources from equipment such
    as commercial type digital VCR compatible with digital serial component signals of
    the SMPTE 292M standard and provides a high quality image without quantisation
    noise. This board accepts the following image formats.
    1920 x 1035/60/2:1 30 2:1 Interlace
    1920 x 1080/60/2:1 30 2:1 Interlace
    1280 x 720/60/1:1 60 Progressive
    1920 x 1080/24sF 24 Progressice (Segmented Frame)
    BNC cable used with the HDSDI connector should be 5C-FB equivalnt cable or
    better.
    Included in option:-
    SDI Board Shield Case
    Connector Cable (Internal) (2) Flat Cable
    Set screw for Shield Case (2) Installation Manual
    A—12
    Overview
    OVERVIEW
    LBV00072; Revision A - 25/09/2001
    -
    - 
    						
    							Remote Control
    All the functions of your HIGHlite Displaysprojector can be controlled using the
    remote control.  The remote control unit can operate either by infra red or by direct
    connection to the projector via a hard wire connection.
    For infra red operation the remote control requires to be powered by 2 AAA
    (HP16/RO3/LR03) alkaline batteries. The battery compartment is located on the
    back of the remote control. To remove the compartment cover press and open as
    shown below.
    Insert the first battery into the compartment according to the (+) and (-) indications
    inside the case and it to the back of the compartment. Insert the second battery by
    pivoting it against the first and pushing down into place. When the batteries are
    securely in place, replace the battery compartment cover.
    When using infra red operation the remote control has an effective range of about
    7m (23 feet) and at an angle of 30° above, below, to the left and to the right of the
    remote control sensors located at the front and the rear of the projector.
    The remote control should not be exposed to heat, steam, water or any other liquid.
    If the remote control gets wet, wipe it dry immediately. 
    When remote control buttons are pressed and held down the main unit function
    keys may not operate.
    You cannot operate the projector using the remote control if the remote ID is not
    set to [00] or the remote ID is not the same as the projector ID. 
    Very bright flourescent lighting or Infra Red translation systems may saturate the
    projectors’ Infra Red receiver rendering the remote control inoperative.
    A—13
    0verview
    OVERVIEW
    LBV00072; Revision A - 25/09/2001
    -
    -
    - 
    						
    							A—14
    Overview
    OVERVIEW
    LBV00072; Revision A - 25/09/2001 
    						
    							Installation Guidelines...................................................... B—1
    Screen Requirements................................................... B
    —1
    Positioning the Projector  .............................................. B
    —4
    Installation ....................................................................... B—7
    Attaching the Power Cable Stopper ........................... B—7
    Lens Installation .......................................................... B—8
    Setting Up the Projector ................................................. B—11
    Reflecting the Displayed Image ............................... B—12
    Shutter Mechanism ................................................... B—12
    Turning Off the Projector ........................................... B—12
    Startup Screen (Language Select) ................................. B—13
    Connecting Signal Sources ............................................ B—15
    System Installation
    Section B: System Installation
    INSTALLATION
    LBV00072; Revision A - 25/09/2001 
    						
    							System Installation
    INSTALLATION
    LBV00072; Revision A - 25/09/2001 
    						
    							This installation section explains how to install the projector for optimum results.
    To do this, it is necessary to determine the following:
    1. The type of screen and whether front or rear projection is to be used.
    2. The projector location and therefore the type of lens to be used.
    3. The method of mounting for the projector.
    4. The type of input source to be used with the projector.
    Screen Requirements
    As virtually all commercially available screens will give a pleasing image you
    should choose according to your individual requirements. However, to achieve 
    optimum results we recommend a low gain (1.2 - 1.3), non-perforated screen for
    front projection, this will keep hot spotting and light loss to a minimum whilst 
    providing wide viewing angles. 
    Regardless of the type of screen used, it is important that your screen is of sufficient
    height to display the images at the aspect ratios intended to be used. Use the 
    following tables to check that you are able to display the full image on your screen.
    If you have insufficient height, you will have to reduce the overall image size in
    order to display the full image on your screen.
    B—1
    System Installation
    Installation Guidelines
    INSTALLATION
    LBV00072; Revision A - 25/09/2001
    Screen Width
    (metres)
    2.40
    3.00
    3.60
    4.20
    4.80
    6.00
    10.004 x 3
    1.80
    2.25
    2.70
    3.15
    3.60
    4.50
    7.505 x 4
    1.92
    2.40
    2.88
    3.36
    3.84
    4.80
    8.008 x 5
    1.5
    1.87
    2.25
    2.62
    3.00
    3.75
    6.2514 x 9
    1.54
    1.93
    2.31
    2.70
    3.09
    3.86
    6.4316 x 9
    1.35
    1.69
    2.02
    2.36
    2.70
    3.38
    5.63Screen Height (metres) Needed to Display Full Image with Aspect Ratio: 
    						
    							For optimum viewing, the screen should be a flat surface perpendicular to the floor.
    The bottom of the screen should be 1.2m (4 feet) above the floor and the front row
    of the audience should not have to look up more than 30° to see the top of the
    screen (see opposite).
    The distance between the front row of the audience and the screen should be at least
    twice the screen height and the distance between the back row and the screen should
    be a maximum of 8 times the screen height. The screen viewing area should be
    within a 60° range from the face of the screen.
    If you intend to use a rear projection screen you must ensure you have sufficient
    distance behind the screen for the projector to be correctly located Rear projection
    has the advantage that the projector cannot be seen and higher ambient light levels
    can be tolerated. Although the image can be flipped to rear projection and displayed
    without the need for extra mirrors or equipment, it makes the installation more 
    complicated and advice should be sought from your local dealer before attempting
    an installation in this way.
    B—2
    System Installation
    INSTALLATION
    LBV00072; Revision A - 25/09/2001
    Screen Width
    (feet)
    8 0
    10 0
    12 0
    14 0
    16 0
    20 0
    30 04 x 3
    6 0
    7 6
    9 0
    10 6
    12 0
    15 0
    22 65 x 4
    6 5
    8 0
    9 7
    11 2
    12 10
    16 0
    24 08 x 5
    5 0
    6 3
    7 6
    8 9
    10 0
    12 6
    18 914 x 9
    5 2
    6 5
    7 9
    9 0
    10 8
    12 10
    19 416 x 9
    4 6
    5 8
    6 9
    7 11
    9 0
    11 4
    16 11Screen Height (feet/inches) Needed to Display Full Image with Aspect Ratio: 
    						
    All Digital Projection manuals Comments (0)

    Related Manuals for Digital Projection Highlite 4000dsx User Manual