Dell R730 Manual

							Figure 81. Removing the system board
1.release pin2.system board3.system board holder
Next steps
1.Install the system board. 
2.Follow the procedure listed in the After working inside your system section.
141 
						

							Related links
Safety instructions
Before working inside your system
Removing the cooling shroud
Removing the cooling fan assembly
Removing the hard drive tray
Removing an AC power supply unit
Removing a DC power supply unit
Removing expansion card risers
Removing the integrated storage controller card
Removing the optional internal dual SD module
Replacing the optional internal USB memory key
Removing the PCIe card holder
Removing the cable retention bracket
Removing a heat sink
Removing a processor
Removing memory modules
Removing the network daughter card
Installing the system board
After working inside your system
Installing the system board
Prerequisites
1.Follow the safety guidelines listed in the Safety instructions section.
2.Follow the procedure listed in the Before working inside your system section.
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and 
simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support  team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product.
Steps
1.Unpack the new system board assembly.
CAUTION: Do not lift the system board by holding a memory module, processor, or other components.
CAUTION: Take care not to damage the system  identification button while placing the system board into the chassis.
2.Hold the touch points and lower the system board into the chassis.
3.Push the system board toward the back of the chassis until the board clicks into place.
142 
						

							Figure 82. Installing the system board
1.release pin2.system board3.system board holder
Next steps
1.Install the Trusted Platform Module (TPM). For information about how to install the TPM, see the Installing the Trusted Platform Module section. For more information on the TPM, see the Trusted Platform Module section.
NOTE: The TPM plug-in module is attached to the system board and cannot be removed. A replacement TPM plug-
in module will be provided for all system board replacements where a TPM plug-in module was installed.
2.Replace the following:
a.Cable retention bracket
b.PCIe card holder
c.Integrated storage controller card
d.Internal USB key (if applicable)
e.Internal dual SD module
f.All expansion card risers
143 
						

							g.Heat sink(s)/heat sink blank(s) and processors(s)/processor blank(s)
h.Memory modules and memory module blanks
i.Network daughter card
j.Cooling fan assembly
k.Cooling shroud
l.Power supply unit(s)
3.Reconnect all cables to the system board.
NOTE: Ensure that the cables inside the system are routed along the chassis wall and secured using the cable 
securing bracket.
4.Follow the procedure listed in the After working inside your system section.
5.Import your new or existing iDRAC Enterprise license. For more information, see Integrated Dell Remote Access Controller  User
						

							Restoring the Service Tag by using the Easy Restore feature
The Easy Restore feature enables you to restore your system
						

							Figure 83. Installing the TPM
1.TPM2.TPM connector3.slot on the TPM connector4.plastic bolt5.slot on the system board
Next steps
1.Install the system board.
2.Follow the procedure listed in the After working inside your system section.
Related links
Safety instructions
Before working inside your system
Installing the system board
After working inside your system
Initializing the TPM for BitLocker users
Initialize the TPM.
For more information about initializing the TPM, see http://technet.microsoft.com/en-us/library/cc753140.aspx.
The TPM Status changes to Enabled, Activated.
Initializing the TPM for TXT users
1.While booting your system, press F2 to enter System Setup.
2.On the System Setup Main Menu screen, click System BIOS 
						

							the correct drive class will enable the critical areas of quality, functionality, performance, and reliability to be optimized for the target implementation.
NOTE: Do not mix enterprise-class hard drives with entry hard drives.
Choosing the right drive type depends on the usage pattern. Improper use of entry hard drives (workload rating exceeds 55TB/year)  will lead to  signi
						

							Figure 84. Removing a 2.5-inch hard drive blank
1.hard drive blank2.release button
Related links
Safety instructions
Removing the optional front bezel
Installing a 2.5-inch hard drive blank
Prerequisites
1.Follow the safety guidelines listed in the Safety instructions section.
2.If installed, remove the front bezel.
Steps
Insert the hard drive blank into the hard drive slot until the release button clicks into place.
Figure 85. Installing a 2.5-inch hard drive blank
1.hard drive blank
Next steps
If removed, install the front bezel.
Related links
Safety instructions
Removing the optional front bezel
148 
						

							Removing a 3.5-inch hard drive blank
Prerequisites
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and 
simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support  team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
CAUTION: To maintain proper system cooling, all empty hard drive slots must have hard drive blanks installed.
1.Follow the safety guidelines listed in the Safety instructions section.
2.If installed, remove the front bezel.
Steps
Press the release button and slide the blank out of the hard drive slot.
Figure 86. Removing a 3.5 inch hard drive blank
1.hard drive blank2.release button
Next steps
If applicable, install the front bezel.
Related links
Safety instructions
Removing the optional front bezel
Installing the optional front bezel
Installing a 3.5-inch hard drive blank
Prerequisites
1.Follow the safety guidelines listed in the Safety instructions section.
2.If installed, remove the front bezel.
Steps
Insert the hard drive blank into the hard drive slot until the release button clicks into place.
149 
						

							Figure 87. Installing a 3.5 inch hard drive blank
1.hard drive blank
Next steps
If applicable, install the front bezel.
Related links
Safety instructions
Removing the optional front bezel
Installing the optional front bezel
Removing a hot swappable hard drive or SSD
Prerequisites
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and 
simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support  team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
1.Follow the safety guidelines listed in the Safety instructions section.
2.Follow the procedure listed in the Before working inside your system section.
3.If applicable, remove the bezel.
4.If applicable, remove the system cover to remove hot-swappable drives inside your system. 
5.Using the management software, prepare the hard drive for removal. If the hard drive is online, the green activity or fault  indicator  flashes while the drive is turning  o