Home > Dell > Projector > Dell Projector 7700 User Manual

Dell Projector 7700 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Dell Projector 7700 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 327 Dell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Using Your Projector51
    CHANGE PASSWORD—Key in the original password. Then, enter the new 
    password and confirm the new password again.
    POWER SETTINGS—Select and press   to activate power settings. The power 
    settings menu provides the following options: 
    						
    							52Using Your Projector
    QUICK SHUTDOWN—Select On to turn off the projector with a single press of 
    the Power button. This function allows the projector to quickly power off 
    with an accelerated fan speed. Slightly higher acoustic noise is expected 
    during quick power off.
     
    NOTE: Before you turn on the projector again, wait for 60 seconds to 
    allow the internal temperature to stabilize. The projector will take a 
    longer time to turn on if you try to power on immediately. Its cooling fan 
    will run at full speed for about 30 seconds to stabilize the internal 
    temperature.
    P
    OWER SAVING—Select Off to disable Power Saving mode. By default, the 
    projector is set to enter power saving mode after 120 minutes of no activity. 
    A warning message appears on screen showing a 60 seconds countdown 
    before switching to power saving mode. Press any button during the 
    countdown period to stop the power-saving mode.
    You can also set a different delay period to enter power saving mode. The 
    delay period is the time you want the projector to wait without an input 
    signal. Power saving can be set to 30, 60, 90, or 120 minutes.
    If an input signal is not detected during the delay period, the projector 
    turns off. To turn on the projector press the Power button.
    W
    IRELESS—Select Always On or Off when Standby to set the Wireless/LAN 
    module on/off while the projector is standby status.
    VGA O
    UTPUT—Select Always On or Off when Standby the VGA output 
    feature at projector standby status.
    L
    AMP MODE—Allows you to select between Normal or ECO mode.
    Normal mode operates at full power level. ECO mode operates at a lower 
    power level which may provide longer lamp life, quieter operation, and 
    dimmer luminance output on the screen.
    L
    AMP HOUR RESET—Press   and select the Confirm option to reset the 
    lamp hour. 
    						
    							Using Your Projector53
    PIP SETTINGS—Select and press   to activate pip settings. The pip settings 
    menu provides the following options:
    P
    ICTURE IN PICTURE—Select On to enable the picture in picture display. 
    Select Off to disable the feature.
    S
    ECOND SOURCE—Allows you to select the possible second source is available 
    in the OSD selection depending on the current primary input source. See 
    PIP Combination Sources on page 113.
    S
    WAP—Press   to swapping the first and second source displays.
    S
    IZE—Allows you to adjust the image size of the second source. The 
    options are: Small, Mid, Large, and Half.
    L
    AYOUT—Allows you to change the second source position to the four 
    different corners. The options are: To p  L e f t, To p  R i g h t, Bottom Left, and 
    Bottom Right.
    INFORMATION—The information menu displays the current projector settings. 
    						
    							54Using Your Projector
    LANGUAGE
    Allows you to set the language for the OSD. Press   to activate the Language 
    menu.
    HELP
    If you encounter problems with your projector, you can access the help menu for 
    troubleshooting. 
    						
    							Using Your Projector55
    Wireless Networking Installation
     NOTE: Your computer must have the following minimum system requirements:
    Operating System:
    •Windows
    Microsoft Windows XP™ Home or Professional Service pack 2 (32-bit 
    recommended), Windows Vista 32-bit, and Windows
    ® 7 Home or Professional 
    32-bit or 64-bit
    •MAC 
    MacBook and above, MacOS 10.5 and above
    Minimum Hardware:
    aIntel Dual Core 1.8 MHz or higher
    b256 MB of RAM required, 512 MB or more recommended
    c10 MB of available hard-disk space 
    dnViDIA or ATI graphic card must with 64 MB VRAM or above
    eEthernet adapter (10 / 100 bps) for an Ethernet connection 
    fA supported WLAN adapter for a WLAN connection (any NDIS-compliant 
    802.11b or 802.11g or 802.11n WiFi device)
    Web browser
    Microsoft Internet Explorer 6.0 or 7.0 (recommended) or 8.0, Firefox 2.0, Safari 
    3.0, and above 
    						
    							56Using Your Projector
    Enable Wireless on the Projector
    In order to use your projector wirelessly, you need to complete the steps below:
    1
    Install the optional wireless dongle. See Installing the Optional Wireless 
    Dongle on page 11.
    2Connect the power cable to the wall outlet and press the power button.
    3Press the Menu button on your projector control panel or remote control.
     NOTE: Use  ,  ,   and   buttons to navigate and   to select.
    4
    The wireless connection default is Enabled. See Wireless Settings on 
    page 48.
    5Access the INPUT SOURCE menu, select Wireless/USB and then select 
    Wireless Display on the sub-menu. See INPUT SOURCE WIRELESS/USB 
    on page 38. 
    						
    							Using Your Projector57
    The Wireless Guide Screen shown below appears:
     NOTE: If wireless connection is disabled, then follow these steps to set up: 
    ADVANCED SETTINGS J Wireless Settings J Wireless J Connected. The 
    image input source will be automatically switched to wireless screen when 
    wireless option is selected in this step.
    6
    Take note of the LOGIN CODE, NETWORK NAME (SSID), and IP 
    ADDRESS
    . You will need these information to log in later. 
    						
    							58Using Your Projector
    Install the Wireless Application Software on Your Computer
    7Connect your computer to the 7700FullHD wireless network.
     NOTE: 
    • Your computer must have wireless network function to detect the 
    connection.
    • When you connect to the 7700FullHD wireless network, you will lose 
    wireless connectivity with other wireless networks.
     NOTE: Remember to turn off all proxies. (In Microsoft® Windows Vista: Click 
    Control Panel J Internet Options J Connections J LAN Settings)
    8
    Open your Internet browser. You will be automatically directed to the 
    7700FullHD Web Management web page. 
    						
    							Using Your Projector59
     NOTE: If the web page does not load automatically, enter the IP address 
    (default IP address is 192.168.100.10) noted from the projector’s screen in the 
    browser’s address bar.
    9
    The 7700FullHD Web Management page opens. For first time use, click 
    Download. 
    10Select the appropriate operating system, then click Download. 
    						
    							60Using Your Projector
    11Click Run to proceed with the 
    one-time installation of the 
    software.
     NOTE: You may choose to 
    save the file and install it at a 
    latter time. To do this, click 
    Save.
     
    NOTE: If you are unable to 
    install the application because of inadequate rights on the computer, please 
    contact your network administrator.
    12
    The installation software will launch. Follow the on-screen instructions to 
    complete setup. 
    						
    All Dell manuals Comments (0)

    Related Manuals for Dell Projector 7700 User Manual