dell latitude x200 User Manual

Palm Rest: Dell Latitude X200 Service Manual
 
 
file:///F|/Service%20Manuals/Dell/Latitude/x200/palmrest.htm (4 of 4) \
[2/28/2004 8:23:59 AM] 

Hard Drive: Dell Latitude X200 Service Manual
Back to Contents Page 
Hard Drive 
Dell™ Latitude™ X200 Service Manual
Removing the Hard Drive 
NOTICE: Disconnect the computer and any attached devices from electrical 
outlets. 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
touching an unpainted metal surface on the computer. 
NOTICE: Read Preparing to Work Inside the Computer before performing the 
following procedure. 
1.  Remove the 
battery. 
2.  Remove the 
keyboard. 
3....

Hard Drive: Dell Latitude X200 Service Manual
 
1 hard drive
2 M2 x 5.5-mm screws (3)
3 hard drive connector
5.  Disconnect the hard drive connector from the system board. 
6.  Lift the hard drive up and out of the bottom case. 
Back to Contents Page
 
 
 
file:///F|/Service%20Manuals/Dell/Latitude/x200/hdd.htm (2 of 2) [2/28\
/2004 8:24:00 AM] 

Hinge Covers and Display Assembly: Dell Latitude X200 Service Manual
Back to Contents Page 
Hinge Covers and Display Assembly 
Dell™ Latitude™ X200 Service Manual
  Hinge Covers
  Display Assembly
Hinge Covers
Removing the Hinge Covers 
1.  Remove the battery. 
2.  On the inside of the battery bay, use your fingers to unhook the hinge c\
overs  from the back of the computer. 
 
file:///F|/Service%20Manuals/Dell/Latitude/x200/display.htm (1 of 7) [\
2/28/2004 8:24:01 AM] 

Hinge Covers and Display Assembly: Dell Latitude X200 Service Manual
1hinge covers (2)
3.  Open the display 180 degrees. 
4.  Push up on the hinge covers to remove them from the computer. 
Replacing the Hinge Covers 
1.  Open the computer all the way (180 degrees) so that it lies flat again\
st your  work surface. 
2.  Place the hinge covers over the display hinges:  a.  The left hinge cover fits over the power button and the right hinge cove\
r fits over the Dell™ AccessDirect™ button. Both hinge covers...

Hinge Covers and Display Assembly: Dell Latitude X200 Service Manual
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
touching an unpainted metal surface on the computer. 
NOTICE: Read Preparing to Work Inside the Computer before performing the 
following procedure. 
1.  Remove the 
battery. 
2.  Remove the 
keyboard. 
3.  Remove the two M2 x 6-mm screws by the display hinges on the top of the \
 computer. 
 
1 M2 x 6-mm screws (2)
4.  Turn the computer over, and remove the...

Hinge Covers and Display Assembly: Dell Latitude X200 Service Manual
 
1 M3 x 5-mm screws (2)
5.  Turn the computer over, and open the display 180 degrees. 
6.  Disconnect the antenna connector. 
file:///F|/Service%20Manuals/Dell/Latitude/x200/display.htm (4 of 7) [\
2/28/2004 8:24:01 AM] 

Hinge Covers and Display Assembly: Dell Latitude X200 Service Manual
 
NOTICE: Do not pull on the signal cable and inverter cable. Pull from the signal\
 
connector and inverter connector to disconnect the cables. 
7.  Disconnect the signal cable from the system board. 
8.  Remove the tape that secures the inverter connector, and then disconnect\
 the  inverter cable from the system board. 
file:///F|/Service%20Manuals/Dell/Latitude/x200/display.htm (5 of 7) [\
2/28/2004 8:24:01 AM] 

Hinge Covers and Display Assembly: Dell Latitude X200 Service Manual
 
1 signal cable
2 inverter cable
3 inverter connector
4 signal connector
9.  Move the display assembly to an upright position and pull it up out of t\
he  bottom case. 
Back to Contents Page
 
 
file:///F|/Service%20Manuals/Dell/Latitude/x200/display.htm (6 of 7) [\
2/28/2004 8:24:01 AM] 

Hinge Covers and Display Assembly: Dell Latitude X200 Service Manual
 
file:///F|/Service%20Manuals/Dell/Latitude/x200/display.htm (7 of 7) [\
2/28/2004 8:24:01 AM]