dell latitude c810 User Manual

Removing and Replacing Parts : Dell Latitude C810 Service Manual 
NOTICE: Be careful when handling the keyboard. The keycaps are fragile, 
easily dislodged, and time-consuming to replace. 
4.  Use a nonmarring tool under the blank key to pry up the keyboard. 
Keyboard Removal 
 
5.  Lift the right end of the keyboard and slide it slightly toward the \
right side of the  computer to disengage the tabs at the left end. 
file:///F|/Service%20Manuals/Dell/Latitude/c810/2e40520.htm (14 of 50)\
 [2/28/2004...

Removing and Replacing Parts : Dell Latitude C810 Service Manual 
6.  Pivot the keyboard and balance it upright on the left side of the co\
mputer. 
Keyboard Cable 
 
7.  Disconnect the keyboard cable and lay the keyboard assembly aside. 
Replacing the Keyboard Assembly 
1.  While bracing the keyboard assembly upright on its left end, connect\
 the  keyboard cable to the interface connector on the system board. 
file:///F|/Service%20Manuals/Dell/Latitude/c810/2e40520.htm (15 of 50)\
 [2/28/2004 8:02:02 AM] 

Removing and Replacing Parts : Dell Latitude C810 Service Manual 
NOTICE: Position the keyboard/track stick flex cable so it is not pinched when 
you replace the keyboard in the bottom case assembly. 
2.  Insert the metal tabs at the left end of the keyboard under the edge\
 of the  bottom case assembly, and fit the keyboard into place. 
3.  Check that the keyboard is correctly installed. The keys should be f\
lush with the  left and right surfaces of the palmrest. 
4.  Reinstall the four screws in the...

Removing and Replacing Parts : Dell Latitude C810 Service Manual 
 
Removing the Hinge Cover 
Hinge Cover 
file:///F|/Service%20Manuals/Dell/Latitude/c810/2e40520.htm (17 of 50)\
 [2/28/2004 8:02:02 AM] 

Removing and Replacing Parts : Dell Latitude C810 Service Manual 
 
1.  Follow the instructions in 
Preparing to Work Inside the Computer. 
2.  Use a nonmarring tool to loosen the hinge cover at the back and at e\
ach side of  the computer. 
3.  Open the display and lift off the hinge cover. 
Removing the Display Assembly 
Display Assembly
file:///F|/Service%20Manuals/Dell/Latitude/c810/2e40520.htm (18 of 50)\
 [2/28/2004 8:02:02 AM] 

Removing and Replacing Parts : Dell Latitude C810 Service Manual 
 
1.  Remove the hinge cover. 
NOTICE: Make sure you remove the flex cable before you remove the display 
assembly. 
Flex Cable 
file:///F|/Service%20Manuals/Dell/Latitude/c810/2e40520.htm (19 of 50)\
 [2/28/2004 8:02:02 AM] 

Removing and Replacing Parts : Dell Latitude C810 Service Manual 
 
2.  Remove the 6-mm screw that secures the display flex cable to the str\
ain relief,  and then use the pull loop to remove the display flex cable from the gra\
phics 
card. 
NOTICE: When reconnecting the flex cable, press down on both ends of the 
connector, not in the middle. Pressing the middle of the connector can d\
amage 
fragile components. 
3.  Open the display and, from the back of the computer, remove the two \
screws  labeled...

Removing and Replacing Parts : Dell Latitude C810 Service Manual 
 
Removing the Display Assembly Bezel 
1.  Use a scribe to pry out the four rubber screw covers located across \
the top of the bezel. 
2.  Remove the four 4-mm screws located across the top of the bezel. 
file:///F|/Service%20Manuals/Dell/Latitude/c810/2e40520.htm (21 of 50)\
 [2/28/2004 8:02:02 AM] 

Removing and Replacing Parts : Dell Latitude C810 Service Manual 
3.  Use a scribe at the indentations to pry out the two plastic screw co\
vers located at the bottom of the bezel. 
4.  Remove the two 4-mm screws located at the bottom of the bezel. 
5.  Separate the bezel from the display-assembly top cover. 
The bezel is secured to the display assembly top cover with plastic tabs\
 around 
the sides. Use a plastic scribe to help separate the bezel from the top \
cover.
Removing the Display Panel 
1....

Removing and Replacing Parts : Dell Latitude C810 Service Manual 
 
Replacing the Display Panel 
NOTE: Use a magnetic screwdriver to reassemble the display panel in the 
display. 
1.  Connect the flex cable to the two connectors on the back of the disp\
lay panel. 
2.  Place the display panel assembly in the top cover, taking care that \
the flex cable  is in place and is not crushed or crimped. 
file:///F|/Service%20Manuals/Dell/Latitude/c810/2e40520.htm (23 of 50)\
 [2/28/2004 8:02:02 AM]