Dell Drac 5 User Guide
Have a look at the manual Dell Drac 5 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 327 Dell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Sensors291 18 Sensors Hardware sensors or probes help you to monitor the systems on your network in a more efficient way by enabling you to take appropriate actions to prevent disasters, such as system instability or damage. You can use the DRAC 5 to monitor hardware sensor for batteries, fan probes, chassis intrusion, power supplies, power consumed, temperature, and voltages. Battery Probes The Battery probes provide information about the system board CMOS and storage RAM on motherboard (ROMB) batteries. NOTE: The Storage ROMB battery settings are available only if the system has a ROMB. Fan Probes The fan probe sensor provides information on: • fan redundancy — the ability of the secondary fan to replace the primary fan if the primary fan fails to dissipate heat at a pre-set speed. • fan probe list — provides information on the fan speed for all fans in the system. Chassis Intrusion Probes The chassis intrusion probes provides status of the chassis, whether chassis is open or closed.
292Sensors Power Supplies Probes The power supplies probes provides information on: • status of the power supplies, whether within the normal threshold value or has crossed threshold value. NOTE: You can set threshold values only from the Dell OpenManage Server Administrator. See the Dell OpenManage Server Administrator User’s Guide for more information. • power supply redundancy, that is, the ability of the redundant power supply to replace the primary power supply if the primary power supply fails. NOTE: If there is only one power supply in the system, the Power Supply Redundancy section will not display. Hardware Performance Probes The hardware performance sensor provides status of the performance of your central processing unit (CPU), whether degraded or normal. The status of the hardware performance sensors is degraded when the CPU is in throttled state. Power Monitoring Probes Power monitoring provides information about the real time consumption of power, in watts and amperes. This information is provided to the DRAC 5 through the baseboard management controller (BMC) firmware sensors. NOTE: This feature is supported only on limited Dell PowerEdge x9xx and xx0x systems. DRAC 5 provides advanced power monitoring features. This includes: • Graphical representation of the system power level in Watts and power supplies in Amperes over a time period. • Maximum, minimum, and average power consumption statistics for the system in Watts and BTU/Hr (British Thermal Unit per Hour) over the last 1 hour, 1 day, and 1 week from the current DRAC time as a graph. • Power consumed by the system in Watts and the average current consumed by each power supply in Amperes.
Sensors293 Graph Information The Graph Information page displays the graphs for the system power level in Watts and power supplies in Amperes over a time period. The page auto refreshes every minute. NOTE: The data is obtained by the DRAC 5 every five minutes and is lost after a DRAC reset, AC power cycle, or a firmware update. NOTE: The graphs may display gaps either when the system is powered down or when the BMC resets. This is because the power sensors are unavailable during this period. Power Consumption in Watts displays the time period over which the data for power is collected. You can set the X-axis range to 1 hour, 1 day, or 1 week from the drop-down menu available on this page. The time period is from the current time set on the DRAC. The Y-axis displays the power consumed by the system in Watts. Power Consumption in Amperes displays the time period over which the data for current is collected. You can set the X-axis range to 1 hour, 1 day, or 1 week from the drop-down menu available on this page. The time period is from the current DRAC time. The Y-axis displays the current consumed by the power supplies in Amperes. If there are more than one power supply units on the system and if the readings are the same, the current graphs may overlap each other. Power Consumption Information The Power Consumption Information page displays the power consumed by the system in Watts and the average current consumed by each power supply in Amperes. This page also displays the status of the probes, probe name, power consumed, the minimum and maximum thresholds at which warning and failure alerts are generated, location of the power supply unit, and the average current consumed by each power supply in Amperes.
294Sensors Power Statistics The Power Statistics page displays the average power consumption and the maximum and the minimum power consumption statistics for the system in Watts and BTU/Hr (British Thermal Unit per Hour) over the last 1 hour, 1 day, or 1 week from the current DRAC time. The data is obtained by the DRAC 5 and is reset if the DRAC undergoes a reset for any reason. Temperature Probes The temperature sensor provides information about the system board ambient temperature. The temperature probes indicate whether the status of the probes is within the pre-set warning and critical threshold value. Voltage Probes The following are typical voltage probes. Your system may have these and/or others present. • CPU [n] VCORE • System Board 0.9V PG • System Board 1.5V ESB2 PG • System Board 1.5V PG • System Board 1.8V PG • System Board 3.3V PG • System Board 5V PG • System Board Backplane PG • System Board CPU VTT • System Board Linear PG The voltage probes indicate whether the status of the probes is within the pre-set warning and critical threshold values.
RACADM Subcommand Overview295 A RACADM Subcommand Overview This section provides descriptions of the subcommands that are available in the RACADM command line interface. help NOTE: To use this command, you must have Log In DRAC 5 permission. Table A-1 describes the help command. Synopsis racadm help racadm help Description The help subcommand lists all of the subcommands that are available when using the racadm command along with a one-line description. You may also type a subcommand after help to get the syntax for a specific subcommand. Output The racadm help command displays a complete list of subcommands. The racadm help command displays information for the specified subcommand only. Supported Interfaces •Local RACADM • Remote RACADM • Telnet/SSH/Serial RACADM Table A-1. Help Command Command Definition helpLists all of the subcommands available to use with racadm and provides a short description for each.
296RACADM Subcommand Overview arp NOTE: To use this command, you must have Execute Diagnostic Commands permission. Table A-2 describes the arp command. Synopsis racadm arp Supported Interfaces • Remote RACADM • Telnet/SSH/Serial RACADM clearasrscreen NOTE: To use this command, you must have Clear Logs permission. Table A-3 describes the clearasrscreen subcommand. Synopsis racadm clearasrscreen Supported Interfaces •Local RACADM • Remote RACADM • Telnet/SSH/Serial RACADM Table A-2. arp Command Command Definition arpDisplays the contents of the ARP table. ARP table entries may not be added or deleted. Table A-3. clearasrscreen Subcommand Definition clearasrscreenClears the last crash screen that is in memory.
RACADM Subcommand Overview297 config NOTE: To use the getconfig command, you must have Log In DRAC 5 permission. Table A-4 describes the config and getconfig subcommands. Synopsis racadm config [-c|-p] -f racadm config -g -o [-i ] Supported Interfaces •Local RACADM • Remote RACADM • Telnet/SSH/Serial RACADM Description The config subcommand allows the user to set DRAC 5 configuration parameters individually or to batch them as part of a configuration file. If the data is different, that DRAC 5 object is written with the new value. Input Table A-5 describes the config subcommand options. NOTE: The -f and -p options are not supported for the serial/telnet/ssh console. Table A-4. config/getconfig Subcommand Definition configConfigures the DRAC 5. getconfigGets the DRAC 5 configuration data.
298RACADM Subcommand Overview Output This subcommand generates error output upon encountering either of the following: • Invalid syntax, group name, object name, index, or other invalid database members • RACADM CLI failures This subcommand returns an indication of how many configuration objects that were written out of how many total objects were in the .cfg file. Table A-5. config Subcommand Options and Descriptions Option Description -fThe -f option causes config to read the contents of the file specified by and configure the DRAC 5. The file must contain data in the format specified in Parsing Rules on page 87. -pThe -p, or password option, directs config to delete the password entries contained in the config file -f after the configuration is complete. -gThe -g , or group option, must be used with the -o option. The specifies the group containing the object that is to be set. -oThe -o , or object option, must be used with the -g option. This option specifies the object name that is written with the string . -i The -i , or index option, is only valid for indexed groups and can be used to specify a unique group. The is a decimal integer from 1 through 16. The index is specified here by the index value, not a named value. -c The -c, or check option, is used with the config subcommand and allows the user to parse the .cfg file to find syntax errors. If errors are found, the line number and a short description of what is incorrect are displayed. Writes do not occur to the DRAC 5. This option is a check only.
RACADM Subcommand Overview299 Examples •racadm config -g cfgLanNetworking -o cfgNicIpAddress 10.35.10.100 Sets the cfgNicIpAddress configuration parameter (object) to the value 10.35.10.110. This IP address object is contained in the group cfgLanNetworking. • racadm config -f myrac.cfg Configures or reconfigures the DRAC 5. The myrac.cfg file may be created from the getconfig command. The myrac.cfg file may also be edited manually as long as the parsing rules are followed. NOTE: The myrac.cfg file does not contain password information. To include this information in the file, it must be input manually. If you want to remove password information from the myrac.cfg file during configuration, use the -poption. getconfig getconfig Subcommand Description The getconfig subcommand allows the user to retrieve DRAC 5 configuration parameters on an individual basis, or all the RAC configuration groups may be retrieved and saved into a file. Input Table A-6 describes the getconfig subcommand options. NOTE: The -f option without a file specification will output the contents of the file to the terminal screen.
300RACADM Subcommand Overview Output This subcommand generates error output upon encountering either of the following: • Invalid syntax, group name, object name, index, or other invalid database members • racadm CLI transport failures Table A-6. getconfig Subcommand Options Option Description -fThe -f option directs getconfig to write the entire RAC configuration to a configuration file. This file can be used for batch configuration operations using the config subcommand. NOTE: The -f option does not create entries for the cfgIpmiPet and cfgIpmiPef groups. You must set at least one trap destination to capture the cfgIpmiPet group to the file. -gThe -g , or group option, can be used to display the configuration for a single group. The groupName is the name for the group used in the racadm.cfg files. If the group is an indexed group, use the -i option. -hThe -h, or help option, displays a list of all available configuration groups that you can use. This option is useful when you do not remember exact group names. -iThe -i , or index option, is valid only for indexed groups and can be used to specify a unique group. The is a decimal integer from 1 through 16. If -i is not specified, a value of 1 is assumed for groups, which are tables that have multiple entries. The index is specified by the index value, not a named value. -oThe -o or object option specifies the object name that is used in the query. This option is optional and can be used with the -g option. -u The -u , or user name option, can be used to display the configuration for the specified user. The option is the login name for the user. -vThe -v option displays additional details with the display of the properties and is used with the -g option.