DELL 2155cdn User Manual

Understanding the Printer Menus479
Draft Mode
Purpose:
To save toner by printing in the draft mode. The print quality is reduced when 
printing in the draft mode.
Va l u e s :
LineTermination
Purpose:
To add the line termination commands.
Va l u e s :
Default Color
Purpose:
To specify the color mode to Color or Black. This setting is used for a print 
job that does not specify a print mode.
Va l u e s :
EnableEnables the Hex Dump feature.
Disable
*Does not print in the draft mode.
EnablePrints in the...

480Understanding the Printer Menus
PDF
Use the PDF menu to change printer settings that only affect the PDF jobs.
 NOTE: Values marked by an asterisk (*) are the factory default menu settings.
Quantity
Purpose:
To specify the number of copies to print.
Va l u e s :
2 Sided Print
 NOTE:  2 Sided Print feature is available only for Dell 2155cdn Multifunction 
Color Printer.
Purpose:
To specify whether to print on both sides of a sheet of paper.
Va l u e :
Print Mode
Purpose:
To specify the print mode.
Va l...

Understanding the Printer Menus481
PDF Password
Purpose:
To specify the password to print the secure PDF. 
Va l u e :
Collated
Purpose:
To specify whether to sort the job.
Va l u e :
Output Size
Purpose:
To specify the output paper size for PDF.
Va l u e :
Layout
Purpose:
To specify the output layout.
Va l u e :
High SpeedPrints with the higher speed than the Normal mode, but the quality is 
less. 
Enter PDF PasswordEnter the password to print the secure PDF.
Off
*Does not sort the job. 
OnSorts the...

482Understanding the Printer Menus
Output Color
Purpose:
To specify the output color.
Va l u e :
Network
Use the Network menu to change the printer settings affecting jobs sent to the 
printer through the wired or wireless network.
 NOTE: Values marked by an asterisk (*) are the factory default menu settings.
Ethernet
Purpose:
To specify the communication speed and the duplex settings of Ethernet. The 
change becomes effective after the printer is turned off and then on again.
Va l u e s :
Auto %*
100%...

Understanding the Printer Menus483
Wireless Status
 NOTE: Wireless Status feature is available only when the printer is connected 
using the wireless network.
Purpose:
To confirm the wireless communication status.
Va l u e s :
Wireless Setup
 NOTE: Wireless Setup is available only when the printer is connected using the 
wireless network.
Purpose:
To configure the wireless network interface.
Va l u e s :
Connection Good
Acceptable
Low
No Reception
SSIDDisplays the name that identifies the wireless...

484Understanding the Printer Menus
Manual 
SetupEnter Network (SSID)Specifies a name to identify the wireless 
network. Up to 32 alphanumeric characters 
can be entered.
Infra-
structureSelect when you configure the wireless setting through the 
access point such as a wireless router.
No SecuritySpecifies No Security to configure the 
wireless setting without specifying a 
security method from WEP, WPA-PSK-
TKIP, and WPA-PSK-AES.
WEP(64Bit)Specifies the WEP 64bit key to use through 
the wireless network....

Understanding the Printer Menus485
Reset Wireless
 NOTE: Reset Wireless feature is available only when the printer is connected 
using the wireless network.
Purpose:
To initialize wireless network settings. After executing this function and 
rebooting the printer, all wireless network settings are reset to their default 
values.
Ad-hocSelect to configure the wireless setting without the access 
point such as a wireless router.
No SecuritySelect to configure the wireless setting 
without specifying the...

486Understanding the Printer Menus
Va l u e s :
TCP/IP
Purpose:
To configure TCP/IP settings. 
Va l u e s :
Cancel*Does not reset the wireless setting.
StartResets the wireless setting.
IP Mode Dual Stack
*Uses both IPv4 and IPv6 to set the IP 
address.
IPv4 ModeUses IPv4 to set the IP address.
IPv6 ModeUses IPv6 to set the IP address.
 

Understanding the Printer Menus487
Protocol
Purpose:
To enable or disable each protocol. The change becomes effective after the 
printer is turned off and then on again.
Va l u e s :
IPv4 Get IP Address Auto IP*Sets the IP address automatically. A random 
value in the range of 169.254.1.0 to 
169.254.254.255 that is not currently in use 
on the network is set as the IP address. The 
subnet mask is set as 255.255.0.0.
BOOTPSets the IP address using BOOTP.
RARPSets the IP address using RARP. 
DHCPSets the...

488Understanding the Printer Menus
LPD DisableDisables the LPD port.
Enable
*Enables the Line Printer Daemon (LPD) port.
Port9100 DisableDisables the Port9100 port.
Enable
*Enables the Port9100 port.
IPP DisableDisables IPP port.
Enable
*Enables IPP port.
SMB TCP/IP DisableDisables SMB TCP/IP port.
Enable
*Enables SMB TCP/IP port.
SMB NetBEUI DisableDisables SMB Net BEUI port.
Enable
*Enables SMB Net BEUI port.
WSD DisableDisables WSD port.
Enable
*Enables WSD port.
Network TWAIN DisableDisables Network...