DELL 1350cnw User Manual

Understanding the Printer Menus217
Wireless Status
Purpose:
To display the information on the wireless signal strength. No changes can be 
made on the operator panel to improve the status of the wireless connection.
Va l u e s :
 NOTE: This item is displayed only when the printer is connected with a wireless 
network and 
Wireless LAN is set to Enable.
Wireless Setup
Purpose:
To configure the wireless network interface.
Va l u e s :
Good Indicates good signal strength.
Acceptable Indicates marginal...

218Understanding the Printer Menus
Manual Setup Enter (SSID)Specify a name to identify th
e wireless network. Up to 32 
alphanumeric characters can be entered.
Infra
structure Select when you configure the wireless setting through 
the access point such as a wireless router.
No Security
Specify No Security to configure the 
wireless setting without specifying a 
security method from  WEP, WPA-PSK-
TKIP , and  WPA2-PSK-AES.
WEP (64Bit) Specify the WEP Key (64Bit) to use 
through the wireless network. Up...

Understanding the Printer Menus219
WPA-PSK-
TKIPSelect to configure the wireless setting 
with the security method of WPA-PSK-
TKIP.
Pass 
Phrase 
EntrySpecify the pass phrase of 
alphanumeric characters 
from 8 to 63 only when 
WPA-PSK-TKIP
 is selected 
for  Encryption .
WPA2-PSK-
AES Select to configure the wireless setting 
with the security method of WPA2-PSK-
AES.
Pass 
Phrase 
EntrySpecify the pass phrase of 
alphanumeric characters 
from 8 to 63 only when 
WPA2-PSK-AES
 is selected 
for...

220Understanding the Printer Menus
 NOTE: This item is displayed only when the printer is connected with a wireless 
network.
Reset Wireless
Purpose:
To initialize wireless network settings . After executing this function and 
rebooting the printer, all wireless networ k settings are reset to their default 
values.
 NOTE: This item is displayed only when t he printer is connected with a wireless 
network.
TCP/IP
Purpose:
To configure TCP/IP settings. 
The change becomes effective after the printer is...

Understanding the Printer Menus221
Protocol
Purpose:
To enable or disable each protocol. 
The change becomes effective after the 
printer is turned off and then on.
Va l u e s :
IPv4 Get IP 
AddressPa n e l
Enables the IP address entered on the operator 
panel.
AutoIP* Automatically sets the IP address.
BOOTP Uses BOOTP to set the IP address.
RARP Uses RARP to set the IP address.
DHCP Uses DHCP to set the IP address.
IP Address Manually sets the IP address allocated to the printer.
Subnet Mask Manually...

222Understanding the Printer Menus
Purpose:
To block data received from certain IP addresses through the wired or wireless 
network. You can set up to five IP a ddresses. The change becomes effective 
after the printer is tu rned off and then on.
Va l u e s :
 NOTE: This item is on ly available for LPD or Port9100.
Reset LAN
Purpose:
To initialize wired network data stored  in NVM (non-volatile memory). After 
executing this function and rebooting th e printer, all wired network settings 
are reset to...

Understanding the Printer Menus223
 NOTE: When you use the USB connection and do not use the wireless connection, 
you need to disable the wireless LAN.
USB Settings
Use the  USB Settings  menu to change printer settings affecting a USB 
port.
 NOTE: Values marked by an asterisk (*) ar e the factory default menu settings.
USB Port
Purpose:
To change the USB settings on your printer. The change becomes effective 
after the printer is turned off and then on.
Va l u e s :
System Settings
Use the System...

224Understanding the Printer Menus
Enter 5 in Sleep to put the printer in the Sleep mode five minutes after it 
finishes a job. This uses less energy,  but requires more warm-up time for the 
printer. Enter 5 if your printer shares  an electrical circuit with room lighting 
and you notice lights flickering.
Select a high value if your  printer is in constant use. In most circumstances, 
this keeps the printer ready to operat e with minimum warm-up time. Select a 
value between 5 and 30 minutes for th e...

Understanding the Printer Menus225
mm/inch
Purpose:
To specify the measurement unit displayed after the numeric value on the 
operator panel.
Va l u e s :
 NOTE: The default for mm/inch varies depending on co untry-specific factory 
default.
Def. Paper Size
Purpose:
To specify the default paper size.
Va l u e s :
 NOTE: The default for Def. Paper Size varies depending on country-
specific factory default.
Auto Log Print
Purpose:
To automatically print a job hist ory report after every 10 jobs.
Va l u e s...

226Understanding the Printer Menus
Low Toner Msg
Purpose:
To specify whether to show the alert message when toner is low.
Va l u e s :
Maintenance
Use the  Maintenance  menu to initialize the NV (non-volatile) memory, 
configure the plain paper quality adju stment settings, and configure the 
security settings.
 NOTE: Values marked by an asterisk (*) ar e the factory default menu settings.
F/W Version
Purpose:
To display the version of the controller.
Service Tag
Purpose:
To display the service tag of...