Land Rover Defender 90 110 Workshop Book 4 Rover

BRAKING SYSTEM I70 I 
.. ,. Renewing secondary  plunger seals 
14. Remove the  following items from the plunger: 
f ,*: 
(a) spring 
(b)  seal  retainer 
(c)  recuperating seal 
(d)  washer 
outer  seal. 
15. Taking care  not to damage  the plunger  prise off the 
a 
 b d 14 \I I 
. :: 
I C 
I 
I 
15 
ST1198M 
16. Fit a new  outer  seal using  the  same  procedure  as 
for  the  primary  plunger outer seal by  squeezing  the 
seal  between  the finger  and  thumb into  an  ellipse 
and  press  the raised...

BRAKING SYSTEM 
Incorrect linings. Badly lined shoes.  Distorted 
shoes.  Overloaded  vehicle. Excessive 
braking.  Old hydraulic fluid. 
BRAKING  SYSTEM 
FAULT  DIAGNOSIS 
Replace the shoes,  decrease vehicle load or renew hydraulic  fluid as necessary. 
FAULT I CAUSE I ACTION 
Air in system. Badly lined shoes. Shoes 
distorted or incorrectly  set. Faulty  drums. 
Weak  master  cylinder  mounting. 
FADE 
Check for air in the system  using a Hose Clamp 
and  bleed if necessary.  Check the master...

~.. .:...:;, : ..1 . ... ... :) 
.I..... ..l.l. . . . . ,.. , . .....,. I. ; ... , ..  

76 
c 
8 
- 
CHASSIS AND BODY 
7- 
2 m m 
D 3 
2  

CHASSIS AND BODY 
A FrontDatum 
B Chassis Datum 
C  Front  axle centre  Iine 
D Rear axle centre  line 
1. 239,O-236,5 mm 
2. 82,O-79,5 mm 
3. 633 mm 
4. 2420,6-2418,6 mm 
5. 2306,4-2305,4 mm 
6. 981,2-978,7 mm 
7. 182,7 mm 
8. 41,5-37,O mm 
9. 252-250 mm - . .. 10. 110 mm 
11. 2360 -Wheelbase 
12.  636 - 654 mm 
13. 488-483 mm 
14. 488-483 mm 
15. 3431,l-3426,l mm 
16. 588,3 - 586,3 mm 
17. 2313,8-2311,8 mm 
18. 590,5 mm 
19. 295,25 mm 
20. 519,60 - 517,OO mm 
21. 259,80-258,50 mm 
22. 1242,6 - 1240,6...

76 
N 
CHASSIS AND BODY 
pi 
I a 
4  

CHASSIS AND BODY El 
.. . . .... r”,,.. ’: ., , . :I 4.:: : . ... .~. 
A FrontDatum 
B Chassis Datum 
C Front axle centre line 
D  Rear axle centre 
line 
1. 4148 - 4143 mm 
2. 40093-4005 mm 
3. 978,7-981,2 mm 
4. 22-20” 
5. 252-250 mm 
6. 239-236,5 mm 
7. 3023,3-3022,3 mm 
8. 3030,7-3028,7 mm 
9. 155- 153 mm 
10. 871,2-869,2 mm 
11.  2794 mm - Wheelbase 
12. 488 - 433 mm 
13. 488 - 433 mm 
14. 82-79,5 mm 
15. 750,9 mm 
16. 750,9 mm 
17. 4393 - 4363 mm 
18. 4393 -4363 mm 
19. 2993 - 2953 mm 
20. 500-495...

.  

CHASSIS AND BODY 1761 
DOORS - 1986 ONWARDS 
7  

176 I CHASSIS AND BODY 
REMOVING THE DOOR TRIM - Front and rear 
doors 
1. Prise off the  two  finishers  and remove  the two 
screws  securing  the door  pull. 
-. -- .___ - ...- . 
1. 
5. Lever off the window  regulator center finisher and 
remove  the retaining  screw and withdraw  the 
handle  and bezel. 
2. Remove the single Screw behind the remote control 6- Using a screwdriver, the trim away 
lever. from the door. 
3. Prise off the remote  control  lever bezel. Fitting  door trim 
7. Remove  any...