Land Rover Defender 90 110 Workshop Book 4 Rover

CHASSIS AND BODY 
. I. ,. 9. Fit the  bezels  to  the  locking  button and  remote 
10. Fit  the  single screw  behind  the  remote control 
11. Fit the door  pull and secure  with two screws  and 
12. Fit the  window  regulator  handle and retain  with the 
control 
lever. 
lever. 
finishers. 
single screw  and finisher. 
,  ~ .. I. I 
76 
REMOVING 
WINDOW REGULATORS - rear side 
door 
Fitting regulator 
channel. 
5. Insert  the lifting  arm button  into  the  lifting 
To remove 
1. Remove  the door...

76 
REMOVING EXTERIOR HANDLE - rear side door 
CHASSIS AND BODY 
To remove 
1. Remove the door  trim,  regulator handle, door pull 
and bezels. 
2. Peel  back  sufficient  of the  weather protection  sheet 
to  gain  access 
to the handle  mechanism. 
3. Disconnect  the  actuating  rod from  the handle 
operating  lever. 
4. Remove the  two  screws  and  withdraw the handle 
and  bezels. 
Fitting 
handle 
5. Fit the  handle  to the  door  ensuring  that  the two 
bezels  are 
in position - flat faces...

CHASSIS AND BODY 176 
RENEW REMOTE  CONTROL  LEVER - rear side 
door 
To remove 
1. Remove  the door  trim,  door pull, regulator  handle 
2. Peel-back sufficient  of the  weather protection  sheet 
3. Remove the spring clip and disconnect  the control 
and 
bezels. 
to  gain  access  to the  remote  lever. 
rod from  the locking  button. 
Fitting control  lever 
9. Fit the  plastic  retaining  clips to the  rod  assembly 
10. Connect  the control  rods to the latch  assembly and 
11. Fit the plastic...

76 
Fitting the latch 
7. Fit the  latch  assembly  to the  door  and secure  with 
the  three  screws, noting that  the uppermost  screw 
is longer. 
8. Connect the remote  control  levers to  the  latch 
mechanism  reversing instructions 
3,4 and 5. 
9. Re-seal the weather  protection  sheet  and fit the 
regulator handle,  door pull, door  trim and bezels. 
CHASSIS AND BODY 
REMOVING DOOR GLASS - rear  side door 
To remove 
1. Disconnect  the door  check  rod from  the door  post. 
2. Remove  the...

CHASSIS AND BODY (761 
.: 
. . :.... .Y. ..L.-? 
11. Remove the four  self-tapping  screws - two each 
12. Remove  the inner  and outer  weather  strips from 
.*.

1761 CHASSIS AND BODY 
REMOVING MOUNTING  PANEL - front doors 
To remove 
1. Remove  the  door  trim, window regulator,  door 
pull,  bezels  and weather  protection  sheet. 
2. Remove the four  screws  securing  the window 
regulator  to the  mounting  panel. 
3. Remove the five screws securing  the mounting 
panel  to the  door frame. 
4. Release  the remote  control  lever rod from the  latch 
mechanism  and from  the plastic  clip 
in the 
mounting panel. 
5. Slide the  window regulator  arm from...

CHASSIS AND BODY El 
i.2: I -.. ‘I .. ” Fitting locking  button 
Fitting regulator 
5. Secure  the  locking button assembly to the door 
with  the two  screws. 
6. Connect  the operating rod  to the  latch  mechanism 
and  secure  with the spring  clip. 
7. Reseal  the weather  protection  sheet and fit the 
door 
tnm, door  pull, regulator  handle, and  bezels. 
.. . 
REMOVING WINDOW REGULATOR - front doors 
To remove 
6. Insert the regulator  operating  arms  into  the 
channels. 
7. Fit  and  tighten...

76’ 
5. Remove the  two  screws  securing  the remote 3. Disconnect  the operating  rod  from  the  handle 
control  lever to the  mounting  panel  and withdraw 
the lever  and control rod.  mechanism. 
4. Disconnect 
the rod from  the locking barrel  lever. 
CHASSIS AND BODY 
Fitting remote  control  lever 
6. Feed  the  control  rod  into position  and loosely 
secure  the lever 
to the  mounting panel  with the two 
screws. 
7. Connect  the  control  rod  to  the latch  mechanism 
and  secure  with...

CHASSIS AND BODY 
REMOVE THE DOOR LATCH ASSEMBLY - front 
doors 
76 
To remove 
1. Carry  out the  instructions tc remove  the mounting 
2. Disconnect  the  control  rod from  the handle 
3. Disconnect  the control  rod  from the locking  lever 
4. Disconnect  the locking  button control rod  from the 
panel 
and support  the glass with  timber. 
operating  lever. 
on  the  handle. 
latch  mechanism. 
ST1983M 
5. Remove  the  two  screws  and  remove  the  handle 
assembly from  the door. See exterior...

76 
REMOVING GLASS - front doors 
CHASSIS AND BODY 
To remove 
1. Carry-out the instructions  to remove  the 
2. Remove  the window  regulator. 
3. Push the glass  up to the  top of its travel  and support 
with a  suitable length 
of timber. 
4. Remove  the two self tapping  screws securing  the 
window  glass runner  on  the latch side 
of the door 
and  the single  screw  from the hinge  side. 
mounting 
panel. 
I 1 
ST1976M 
5. Taking care not to damage  the paint  work,  prise 
6. Remove  the timber...