Home > Daewoo > Fridge freezer > Daewoo Frs 2011i Service Manual

Daewoo Frs 2011i Service Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Daewoo Frs 2011i Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 51 Daewoo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							50
    DIAGRAM
    Front PCB
     
    						
    							51
    INSTALLATION GUIDE
    Installation Preparation
    Dimensions( including Door Handles)
    (Width*Depth*Height) 928mm 816mm 1808mm FRS-20
    (Width*Depth*Height) 928mm 896mm 1808mm FRS-24
    Sufficient space from refrigerator back to the
    wall for free air ventilationAvoid direct sunlight.
    Once the installation place is ready follow the installation instructions.If surround temperature of refrigerator is low (below 5), foods can be frozen or the refrigerator can work
    in abnormal way.  
    Check if the refrigerator can pass 
    a doorway or enter a door first.
    Find a suitable place to install
    Installation Preparation
     
    						
    							52
    INSTALLATION GUIDE
    Remove front bottom cover first, if it is attached.Removing Freezer Door 
    1
    Remove the bottom cover first.
    Pull out the left collar of the coupling
    first, then hold the coupling and pull
    out the left water tube.
    3
    Turn top hinge fastener
    counterclockwise 3~4 times. 
    Disconnect the harness wires.
    4
    Lift up the front of hinge to remove. 
    ( After the hinge is removed the
    door can fall down forward. Be
    careful !)
    5
    Be careful not to damage the water
    line when removing the door.
    2Turn top hinge fastener
    counterclockwise 3~4 times. 
    Disconnect harness wires.1Unscrew top hinge cover with a
    screw driver.
    Insert a thin screw driver into the
    side groove of the cover to remove.
    3Lift up the front of hinge to remove.
    (After the hinge is removed the door
    can fall down forward. Be careful !)
    4
    Lift the door straight up to remove.
    2
    Unscrew top hinge cover with a
    screw driver.
    Insert a thin screw driver into the
    side groove of the cover to remove.
    Removing Refrigerator Door 
    If the refrigerator can not enter the door, follow these steps.
     
    						
    							53
    INSTALLATION GUIDE
    How to install Water Line
    WATER SUPPLY KIT
    1.  The water pressure should be 3kgf/cm2or more to run the
    automatic icemaker .
    Checkup your tap water pressure ; if a cup of 180cc is full
    within 10 seconds, the pressure is OK.
    2.  When installing the water tubes, ensure they are not colse to any hot surfaces.
    3.  The water filter only   filters water ;  it does not eliminate any
    bacteria or microbes.
    4. If the water pressure is not so high to run the icemaker ,  call the local plumber to get an additional water pressure pump.
    5.  The filter life depends on the amount of use. We recommend you replace the filter at least once every 6months. When attaching the filter , place it for easy access (removing
    & replacing)
    6.  After installation of refrigerator and water line system, select [WATER] on your control panel and press it for 2~3 minutes to
    supply water into the water tank and dispense water .
    7.  Use sealing tape to every connection of pipes/tubes to ensure there is no water leak.
    8. The water tube should be connected to the cold water line. 
    Check the parts below for installing water supply. 
    Some other necessary parts are available at your local
    service agents.
    Installation Procedure
    1. Join [Connector A], [Connector B] and [Water Valve] to the tap water \
    lines.
    The water valve should be connected to
    the cold water line, otherwise there can be
    a problem of cold water supply.Achtung 
    Achtung 1) Switch off the main water line(valve).
    2) Connect [Water Valve] and [Connector A].
    3) Join [Connector A], [Connector B] to the tap water lines
    Use only [Connector A + Water Valve] in case theres only one tap
    water line.
    Apply the sealing tape to all the joints as the figure shows.If the connectors(valves) do not fit the existing water line, call you\
    r
    service agent for additional guideance and action. 
    2. Connect  the Water Tube to the Water Valve.
    1) Insert the Nut to the Water tube.
    2) Insert the Tube to the Valve as the figure shows.
    3) Fasten the nut to join firmly.
    (30154202400)
    3011202000
    (3010541600)
    (A:3019503200B:3019503300) (3012020700)
    (3014454500)
    (7112401211)
     
    						
    							54
    INSTALLATION GUIDE
    7. Fasten the Water Tube. 5. Attach the Filter Box
    6. Connect the Water Tube to the refrigerator.
    1) Remove the rear cover at the bottom back of the refrigerator.
    2) Insert the fastening ring into the Water tube. 
    (Be careful to follow the direction of the nut.)
    3) Insert the Water Tube into the top of Water Valve, turn the nut clockwise to
    fasten it. (The Water valve is to the right of the motors.)
    4) Check for any bent tubes or water leaks; if so, re-ckeck instalation procedure.
    5) Replace the rear cover. (The Water Tube should be placed between the
    groove of the refrigerator back and motor cover.)
    Water TubeWater Tube
    Nut
    1) Screw and fasten the filter holder to the left/right side of the back of
    refrigerator.
    In case the holder is not fastened well, remove the back paper of
    the tape on the filter holder and attach it.
    2) Insert the filter box into the holder.
    1) Fasten the Water Tube with the [Fastener A] .
    2) Check if the tube is bent or sqeezed.  If so, set it right to prevent any
    water leak.
    Fastener A
    Water Tube
    4. Remove any substances in the filter.
    1) Open the main tap water valve and check if water comes out of the
    Water Tube.
    2) Check if the Water Valve is open in case water does not come out.
    3) Leave the valve open until clean water is coming out.
    Initial water may contain some substances out of filter
    (manufacturing process).
    Set the tube upright as the figure shows.Achtung  Achtung 
    8.  After installation of Water Supply System
    1) Plug the refrigerator, press the [WATER] button on the control panel for
    2~3 minutes to remove any air (bubble) in the pipes and drain out the
    initial water.
    2) Check the water leak again through the water supply system (tubes,
    connectors and pipes) Rearrange the tubes again and do not move the
    refrigerator.
    Water Tube
    Leave a sufficient distance when cutting the tubes.Achtung  Achtung 
    3. Get ready to install the Water Filter
    1) Measure an approximate distance between the filter and the Water
    Tube and cut the tube off filter vertically.
    2) Connect the tubes to the filter as the figure shows.
    Water Valve
     
    						
    							55
    INSTALLATION GUIDE
    Replacing Freezer Door
    2Insert the bottom hole of freezer
    door straight to the bottom hinge pin.1Insert the water tube into the hole of
    the bottom hinge pin first, then 
    Insert the bottom of freezer door into
    the bottom hinge pin.
    3Let the top of door close to the
    cabinet and insert the top hinge
    pin to the top hole of freezer door.
    ( Insert the back of hinge to the
    groove of protrusion first, then
    front to the top hole of door.)
    4Turn the hinge fastener tightly to the
    end.
    Connect harness wirings and screw
    ground wire. 5Insert the water tube far into the
    coupling.
    2Let the top of door close to the
    cabinet and insert the top hinge pin
        to the top hole of freezer door.
    ( Insert the back of hinge to the
    groove of protrusion first, then front
    to the top hole of door.)1Insert the bottom hole of refrigerator
    door straight to the bottom hinge pin
    3Turn the hinge fastener tightly to the
    end.
    Connect harness wirings and screw
    ground wire.
    Click and screw the top hinge
    cover.
    Replacing Refrigerator Door
     
    						
    							56
    INSTALLATION GUIDE
    Refrigerator Leveling & 
    Door Adjustment ( If needed. )
    Refrigerator must be level in order to maintain optimal performance and desirable front appearance.
    (If the floor beneath the refrigerator is uneven, freezer and refrigerator doors look unbalanced.) 
    In case freezer door is lower than refrigerator door ...
    The front of refrigerator needs to be higher just a little than the back for easy
    door closing, but if the wheel is raised too much for door balance, i.e. front of
    refrigerator is too higher than the back, it can be difficult to open the door.
    2Open the doors, unscrew the front
    cover and remove, if it is attached.   1Insert a screw driver (flat tip) into a
    groove of the left wheel (bottom of
    freezer) and turn it clockwise until the
    door is balanced. (clockwise to raise
    freezer door ; counterclockwise to lower)
    Unless the freezer door is balanced
    by step 1, then follow the next steps.
    3Loosen 3 hinge bolts(1 on the left + 2
    on the right) a little. (Do not unfasten
    them completely.) Insert a hexagonal
    wrench into the groove of adjusting
    nut and turn clockwise until the door
    is level.
    4Once the door is balanced, fasten the
    hinge bolts tightly and screw the front
    cover.
    2Loosen 3 hinge bolts(2 on the left + 1
    on the right) a little. (Do not unfasten
    them completely.)
    Insert a hexagonal wrench into the
    groove of adjusting nut and turn
    clockwise until the door is level.1Insert a screw driver (flat tip) into a
    groove of the right wheel (bottom of
    refrigerator) and turn it clockwise until
    the door is balanced. (clockwise to
    raise refrigerator door ;
    counterclockwise to lower)
    Unless the refrigerator door is
    balanced by step 1, then follow the
    next steps.
    Hinge Bolt 
    3Once the door is balanced, fasten
    the hinge bolts tightly.
    In case refrigerator door is lower than freezer door ...
    Remove the back paper of the tape on the filter
    holder and attach the filter holder on a suitable
    place.After installation and/or door leveling, fasten front cover
    with screws.(Remove the screws on the front bottom
    panel first. Click and screw the cover)
    Attaching of W ater Filter HolderFront Cover
    Caution
    Refrigerator Leveling & Door Adjustment( If needed.)
     
    						
    							57
    EXPLODED VIEW AND PARTS LIST
    Total Explded View
    FRS-2011
    CABINET
    MECH ROOM
    17
    16
    15
    14
     1 8
     3
    1113
     2 4 6
     7
     91012
    181920
    21
    31
    23
    32
    26
    2728
    25
    2224
    3334
    29
    30
    56
    3736
    43
    51
    45
    46
    54
    383940
    47
    50
    52
    4948
    44-1
    55
    53
    41
    4244-2
     
    						
    							58
    EXPLODED VIEW AND PARTS LIST
    FRS-2011
    R ROOM
    66
    70
    64
    65
    71
    72
    59
    60
    57
    58
    61
    62
    82
    83
    93
    94
    9798
    92
    99
    9091
    88
    89
    68
    74
    67
    69
    76
    73
    79
    63
    77
    80
    81
    86
    96
    87
    7595
    8485
     
    						
    							
    59
    EXPLODED VIEW AND PARTS LIST
    
    FRS-2011
    F ROOM119
    121
    122
    120
    118
    117
    110
    126
    106
    105
    104
    131
    132
    129
    128
    130
    109
    133
    74
    134
    108
    127
    107
    75100
    101
    114
    102
    103
    112
    124123
    111
    125
    113
     
    						
    All Daewoo manuals Comments (0)

    Related Manuals for Daewoo Frs 2011i Service Manual