D-Link Router DIR-605L User Manual

							7
D-Link DIR-605L User Manua\f
Section 2 - Insta\f\fation
If you are connectin\b the router to a cab\fe/DSL/sate\f\fite modem, p\fease fo\f\fow the steps be\fow:
1.  P\face the router in an open and \ucentra\f \focation. Do not p\fu\b the power adapter into the router. 
2.  Turn the power off on your modem. If there is no on/off switch, then unp\fu\b the modem’s power adapter. Shut down your 
computer.
3.  Unp\fu\b the Ethernet cab\fe (that connects your computer to your modem) from your computer and p\face it into the WAN 
port on the router.  
4.  P\fu\b  an  Ethernet  cab\fe  into  one  of  the  four  LAN  ports  on  the  router.  P\fu\b  the  other  end  into  the  Ethernet  port  on  your 
computer.
5.  Turn on or p\fu\b in your modem.  Wait for the modem to boot (about 30 sec\uonds). 
6.  P\fu\b the power adapter to the router and connect to an out\fet or power strip. Wait about 30 seconds for the router to boot. 
7. Turn on your computer. 
8.  Verify the \fink \fi\bhts on the router. The power \fi\bht, Internet \fi\bht, and the LAN \fi\bht (the port that your computer is p\fu\b\bed 
into) shou\fd be \fit. If not, make sure your computer, modem, and router are powered on and verify the cab\fe connections 
are correct. 
9. Skip to pa\be 16 to confi\bure your router. 
Connec\f \fo Cable/DSL/Sa\felli\fe Modem  
						

							8
D-Link DIR-605L User Manua\f
Section 3 - Confi\buration
Configura\fion
This section wi\f\f show you how to confi\bure your new D-Link wire\fess router usin\b the web-based confi\buration uti\fity.
Web-based Configura\fion U\fili\fy
To  access  the  confi\buration  uti\fity,  open  a  web-browser 
such  as  Internet  Exp\forer  and  enter  the  IP  address  of  the 
router (192.168.0.1) o\ur http://d\finkrouter.  
						

							9
D-Link DIR-605L User Manua\f
Section 3 - Confi\buration
Se\fect the type of Internet connection that Easy Setup Wizard detects, type 
in necessary information and then c\fick \uNext 
to continue.
If  you  se\fected  PPPoE,  enter  your  PPPoE  username  and  password.  C\fick 
Nex\f to continue.
Se\fect  S\fa\fic if your ISP assi\bned you the IP address, subnet mask, \bateway, 
and DNS server addresses.
Note:  Make  sure  to  remove  your  PPPoE  software  from  your  computer\f  The 
software is \bo lo\bger \beede\pd a\bd will \bot work through a router\f
If you se\fected PPTP, enter your PPTP username and password. C\fick  Nex\f to 
continue.  
						

							10
D-Link DIR-605L User Manua\f
Section 3 - Confi\buration
If you se\fected L2TP, enter your L2TP username and password. C\fick  Nex\f to 
continue.
If you se\fected Static, enter your network settin\bs supp\fied by your Internet 
provider. C\fick Nex\f to continue.
In the pa\be of “CURRENT NETWORK SETTING”, you wi\f\f see the INTERNET status 
is “connected”  
						

							11
D-Link DIR-605L User Manua\f
Section 3 - Confi\buration
If you have not re\bistered a myd\fink account, p\fease c\fick “confi\bure” In the 
section “myd\fink account’ and comp\fete the re\bistration form. 
C\fick “Re\bister”
Now you can see the hint that a verification e-mai\f has been sent out. Open 
a new browser to \fo\bin your e-mai\f account for receivin\b the verification 
mai\f.
Once the account verification phase is comp\fete, c\fick "confi\bure" In the 
section "myd\fink account' and \fo\bin myd\fink account.
C\fick "Lo\bin"   
						

							12
D-Link DIR-605L User Manua\f
Section 3 - Confi\buration
Now the router has successfu\f\fy connected to myd\fink service. You can 
down\foad the App "myd\fink \fite" from android market or app\fe store to 
start enjoy mydink service!   
						

							13
D-Link DIR-605L User Manua\f
Section 3 - Confi\buration
Enter the IP address assi\bned by your ISP.
Enter the Subnet Mask assi\bned by your ISP.
Enter the Gateway assi\bned by your ISP.
The defau\ft MAC Address is set to the WAN’s physica\f interface 
MAC address on the Broadband Router. It is not recommended 
that  you  chan\be  the  defau\ft  MAC  address  un\fess  required  by 
your ISP.
The defau\ft MAC address is set to the WAN’s physica\f interface 
MAC address on the Broadband Router. You can use the  Clone 
MAC Address button to copy the MAC address of the Ethernet 
Card insta\f\fed by your ISP and rep\face the WAN MAC address 
with the MAC address of the router. It is not recommended that 
you chan\be the defau\ft MAC address un\fess required by your ISP.
Enter the Primary DNS server IP address assi\bned by your ISP.
This is optiona\f.
Maximum  Transmission  Unit  -  you  may  need  to  chan\be  the 
MTU  for  optima\f  performance  with  your  specific  ISP.  1492  is 
the defau\ft MTU.
IP Address:
Subne\f Mas\b: ISP Ga\feway:
MAC Address:
Clone MAC Address:
Primary DNS  Address:
Secondary DNS  Address:
MTU:
In\ferne\f Se\fup
S\fa\fic (assigned by ISP)
Se\fect  Static  IP  Address  if  a\f\f WAN  IP  information  is  provided  to  you  by  your  ISP. You  wi\f\f  need  to  enter  in  the  IP  address,  subnet  mask,  \bateway 
address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fie\fds must be in the appropriate IP form, which are four 
octets separated by a dot (x.x.x.x). \uThe Router wi\f\f not accept the IP address if it is not in\u this format.
DIR-605L  
						

							14
D-Link DIR-605L User Manua\f
Section 3 - Confi\buration
Choose Dynamic IP Address to obtain IP Address information 
automatica\f\fy from your ISP. Se\fect this option if your ISP does 
not \bive you any IP numbers to use. This option is common\fy 
used for Cab\fe modem services.
The Host Name is optiona\f but may be required by some ISPs. 
The  defau\ft  host  name  is  the  device  name  of  the  Router  and 
may be chan\bed.
The defau\ft MAC Address is set to the WAN’s physica\f interface 
MAC address on the Broadband Router. It is not recommended 
that you chan\be the defau\ft MAC address un\fess required by 
your ISP.
The defau\ft MAC address is set to the WAN’s physica\f interface 
MAC address on the Broadband Router. You can use the “C\fone 
MAC Address” button to copy the MAC address of the Ethernet 
Card insta\f\fed by your ISP and rep\face the WAN MAC address 
with the MAC address of the router. It is not recommended that 
you chan\be the defau\ft MAC address un\fess required by your ISP.
Enter the DNS (Domain Name Server) server IP address assi\bned 
by your ISP. 
Dynamic IP 
Address:
Hos\f Name:
MAC Address:
In\ferne\f Se\fup
Dynamic
Clone MAC  Address:
 DNS 
Addresses:
MTU: Maximum Transmission Unit - You may need to chan\be the MTU for optima\f performance with your specific ISP.
Access Poin\f 
Mode: Checkin\b  this  box  disab\fes  NAT  and  turns  the  Router  into  an 
Access Point on\fy.  
To  manua\f\fy  set  up  the  Internet  connection,  c\fick  the 
Manual  In\ferne\f  Connec\fion  Se\fup  button  on  the  Router’s  openin\b 
window.
DIR-605L  
						

							15
D-Link DIR-605L User Manua\f
Section 3 - Confi\buration
Se\fect Dynamic (most common) or  S\fa\fic. Se\fect S\fa\fic if your 
ISP  assi\bned  you  the  IP  address,  subnet  mask,  \bateway,  and 
DNS server addresses.
Enter your PPPoE user name.
Enter  your  PPPoE  password  and  then  retype  the  password  in 
the next box.
Enter the ISP Service Name (optiona\f).
Enter the IP address (Static PPPoE on\fy).
Enter the Primary and Secondary DNS Server Addresses (Static 
PPPoE on\fy).
Enter a maximum id\fe time durin\b which the Internet connection 
is m a i n t a i n e d   d u r i n \b   i n a c t i v i t y.  To   d i s a b \f e   t h i s   fe a t u re, 
e n a b \f e   Au t o - re c o n n e c t .
Maximum  Transmission  Unit  -  You  may  need  to  chan\be  the 
MTU  for  optima\f  performance  with  your  specific  ISP.  1492  is 
the defau\ft MTU.
Se\fect either Always-on, Manual, or Connec\f-on demand.
PPPoE:
User Name: Password:
Service Name: IP Address:
DNS Addresses:
Maximum Idle  Time:
MTU:
Connec\fion Mode  Selec\f:
In\ferne\f Se\fup
PPPoE 
Choose  PPPoE  (Point  to  Point  Protoco\f  over  Ethernet)  if  your  ISP  uses  a  PPPoE  connection. Your  ISP  wi\f\f  provide  you  with  a 
username and password. This option is typica\f\fy used for DSL services. Make sure to remove your PPPoE software from your 
computer. The software is no \fon\ber need\ued and wi\f\f not work throu\bh a router.
DIR-605L  
						

							16
D-Link DIR-605L User Manua\f
Section 3 - Confi\buration
Se\fect Dynamic (most common) or  S\fa\fic. Se\fect S\fa\fic if your 
ISP  assi\bned  you  the  IP  address,  subnet  mask,  \bateway,  and 
DNS server addresses.
Enter the IP address (Static PPTP on\fy).
Enter the Primary and Secondary DNS Server Addresses (Static 
PPTP on\fy).
Enter the Gateway IP Address provided by your ISP.
The DNS server information wi\f\f be supp\fied by your ISP (Inter -
net Service Provider.)
Enter the Server IP provided by your ISP (optiona\f).
Enter your PPTP account name.
Enter  your  PPTP  password  and  then  retype  the  password  in 
the next box.
Enter a maximum id\fe time durin\b which the Internet connection 
is maintained durin\b inactivity. To disab\fe this feature, enab\fe 
Auto-reconnect.
Maximum Transmission Unit - You may need to chan\be the MTU 
for optima\f performance. 
Se\fect either A\fways-on, Manua\f, or Connect-on demand.
PPTP:
IP Address:
Subne\f Mas\b:
Ga\feway: DNS:
In\ferne\f Se\fup
PPTP
Choose PPTP (Point-to-Point-Tunne\fin\b Protoco\f ) if your ISP uses a PPTP connection. Your ISP wi\f\f provide you with a username 
and password. This option is typica\f\fy used for DSL services. 
Server IP:
PPTP Accoun\f:
PPTP Password:
 
Maximum Idle  Time:
MTU:
Connec\f Mode:
DIR-605L