D-Link Dsh8 Manual

							
 
GE-DSH-73/DSH-82 and DSH-82-PoE User Manual  37 
Chapter 4 
Console Management  
Connecting to the Console Port 
The supplied cable which one end is RS- 232 connector and the other end is RJ-45 
connector. Attach the end of  RS-232 connector to PC or terminal and the other end of 
RJ-45 connector to the console  port of the switch. The connected terminal or PC must 
support the terminal emulation program. 
Figure 4-1: RS-232 to RJ-45 cable 
 
DB9/ RJ-45 Connector Pinouts 
 
 DB9-PIN RJ-45 Connector 
1    1   Orange/White 
2    2   Orange 
3    3   Green/White 
4    4   Blue 
5    5   Blue/White 
6    6   Green 
7    7   Brown/White 
8    8   Brown 
12 345
12 34
9   
						

							
Chapter 4: Console Management 
38  GE-DSH-73/DSH-82 and DSH-82-PoE User Manual 
Login in the Console Interface  
To configure the system, connect a serial cable to a COM port on a PC or notebook 
computer and to RJ-45 type serial (console ) port of the Managed Industrial Switch. 
The console port of the Managed Industrial  Switch is DCE already, so that you can 
connect the console port directly throug h PC without the need of Null Modem. 
Figure 4-2: Connecting the Switch to a PC 
 
A terminal program is required to make th e software connection to the GE-DSH series 
Managed Industrial Switch. Windows Hype r Terminal program is a good choice. 
Hyper Terminal can be acce ssed from the Start menu.  
1. Click  START, then Programs/Accessories  and then Hyper Terminal . 
When the following screen appears, make  sure that the COM port should be 
configured as: 
Baud Rate: 9600 bps 
Data Bits:  8 
Parity:  none 
Stop Bit: 1 
Flow control:  None  
						

							
 Chapter 4: Console Management 
GE-DSH-73/DSH-82 and DSH-82-PoE User Manual  39 
Figure 4-3: The COM1 properties window 
 
2.  Once the terminal has connected to th e device, power on the GE-DSH series 
Managed Industrial Switch, the terminal  will display that it is running testing 
procedures.  
3.  Then, the following message asks th e login password. The factory default 
password as following and the login  screen in below figure appears. 
User name: admin 
Password:  admin 
Figure 4-4: The login screen 
  
						

							
Chapter 4: Console Management 
40  GE-DSH-73/DSH-82 and DSH-82-PoE User Manual 
NOTE: For security reasons, please change  and memorize the new password after 
this first setup.  
Only enter commands in lowercase lette rs when in the console interface. 
 
CLI Management 
The system supports the console management -CLI command. After you log in on to 
the system, you will see a command prompt . To enter CLI management interface, 
type in enable command. 
Figure 4-5: The CLI command interface 
  
						

							
 Chapter 4: Console Management 
GE-DSH-73/DSH-82 and DSH-82-PoE User Manual  41 
CLI commands and descriptions 
 
Modes Access Method Prompt Exit Method About This Model 
User EXEC Begin a session 
with your switch.  switch> Enter logout or 
quit.  The user commands 
available at the user level 
are a subset of those 
available at the privileged 
level. 
Use this mode to: 
• Perform basic tests. 
• Display system 
information. 
Privileged 
EXEC 
Enter the enable 
command while in 
User EXEC mode. 
switch#  
Enter disable to 
exit.  The privileged command is 
the advanced mode. 
Use this mode to 
• Display advanced 
function status 
• Save configuration 
Global 
Configuration 
Enter the 
configure 
command while in 
privileged EXEC 
mode. 
switch 
(config)# 
To exit to 
privileged EXEC 
mode, enter exit 
or end  Use this mode to configure 
those parameters that are 
going to be applied to your 
switch. 
VLAN 
database 
Enter the vlan 
database 
command while in 
privileged EXEC 
mode. 
switch 
(vlan)# 
To exit to user 
EXEC mode, 
enter exit.  Use this mode to configure 
VLAN-specific parameters. 
Interface 
configuration 
Enter the interface 
of fast Ethernet 
command (with a 
specific interface) 
while in global 
configuration 
mode.  switch 
(config-if)# To exit to global 
configuration 
mode, enter exit. 
To exit to 
privileged EXEC 
mode, enter exit 
or end.  Use this mode to configure 
parameters for the switch 
and Ethernet ports. 
 
  
						

							
Chapter 4: Console Management 
42  GE-DSH-73/DSH-82 and DSH-82-PoE User Manual  
						

							
 
GE-DSH-73/DSH-82 and DSH-82-PoE User Manual  43 
Chapter 5 
Web-Based Management  
About Web-based Management 
The Managed Industrial Switch offers ma nagement features that allow users to 
manage the Managed Industrial Switch fr om anywhere on the network through a 
standard browser such as Mi crosoft Internet Explorer. 
The Web-Based Management supports Internet  Explorer 6.0. It is based on Java 
Applets with an aim to reduce networ k bandwidth consumption, enhance access 
speed and present an easy viewing screen. 
NOTE:  By default, IE 6.0 or later version does not allow Java Applets to open sockets. 
The user has to explicitly modify the browser setting to enable Java Applets to use 
network ports. 
The Managed Industrial Switch can be co nfigured through an Ethernet connection, 
make sure the manager PC must be set  on same the IP subnet address with the 
Managed Industrial Switch.  
For example, the default IP address of  the Managed Industrial Switch is 
192.168.0.100, then the manager PC should  be set at 192.168.0.x (where x is a 
number between 1 and 254, except 100), and the default subnet mask is 
255.255.255.0.  
If you have changed the default IP addre ss of the Managed Industrial Switch to 
192.168.1.1 with subnet mask  255.255.255.0 via console, then the manager PC 
should be set at 192.168.1.x (where x is  a number between 2 and 254) to do the 
relative configuration on manager PC.  
						

							
Chapter 5: Web-Based Management 
44  GE-DSH-73/DSH-82 and DSH-82-PoE User Manual 
 
 
 
 
 
 
 
 
Requirements 
• Workstations of subscribers running  Windows 98/ME, NT4.0, 2000/2003/XP, MAC 
OS9 or later, Linux, UNIX or other platform  compatible with TCP/IP protocols.    
•  Workstation installed with Et hernet NIC (Network Card) 
•  Ethernet Port connect 
o Network cables - Use standard network  (UTP) cables with RJ45 connectors. 
o  Above PC installed with WEB Browser  and JAVA runtime environment Plug-in 
NOTE:  We recommend using Internet Explorer 6. 0 or above to access GE-DSH series 
Managed Industrial Switch. 
Logging on the Switch 
1. Use Internet Explorer 6.0 or above Web browser. Enter the factory-default IP 
address to access the Web interface. The factory-default IP Address as following:  
 http://192.168.0.100  
2. When the following login screen appear s, please enter the default username 
admin with password admin (or the us ername/password you have changed via 
console) to login the main screen of Man aged Industrial Switch. The login screen in 
Figure 5-1 appears. 
Default User name:  admin  
Default Password:  admin  
						

							
 Chapter 5: Web-Based Management 
GE-DSH-73/DSH-82 and DSH-82-PoE User Manual  45 
Figure 5-1:  Login screen 
 
 
3. After entering the username and passwor d, the main screen appears as shown in 
Figure 5-2. 
Figure 5-2:  Default main page 
 
4. The Switch Menu on the left of the Web page let you access all the commands and 
statistics the Switch provides.  
Now, you can use the Web management  interface to continue the switch 
management or manage the Managed Indu strial Switch by Web interface. The 
Switch Menu on the left of the web page  let you access all the commands and 
statistics the Managed Industrial Switch provides.  
						

							
Chapter 5: Web-Based Management 
46  GE-DSH-73/DSH-82 and DSH-82-PoE User Manual 
NOTE:  
1. We recommend using Internet Explorer 6.0 or above to access GE-DSH-82 series 
Managed Industrial Switch. 
2. The changed IP address take effect immedi ately after clicking on the Save button. 
You need to use the new IP addres s to access the Web interface. 
3. For security reasons, please change  and memorize the new password after this 
first setup. 
4. Only enter commands in lowercase le tters when using the web interface. 
System 
Use the System menu items to display and  configure basic administrative details of 
the Managed Industrial Switch. Under System  the following topics are provided to 
configure and view the system information:  This section has the following items: 
 
System Information  Provides basic system descriptio n, including contact information 
IP Configuration  Sets the IP address for management access 
DHCP Server  Configure the Switch as a DHCP server for assigning dynamic IP 
addresses to devices on a network. 
TFTP  Upgrade the firmware via TFTP server 
Save/view the switch configuration to remote host 
Upload the switch configuration from remote host 
Fault Relay Alarm  Provides relay output for port breakdown, power fail 
SNTP Configuration  Simple Network Time Protocol. Configures SNTP client settings, including 
broadcast mode or a specified list of servers 
IP Security  Supports 10 IP addresses that have  permission to access the switch 
management and to prevent unauthorized intruder. 
User Authentication  Allows configuring the system user name and password required to 
access the web pages or log in from CLI. 
Factory Default  Reset the configuration of the Managed Industrial Switch  
System Reboot  Restarts the switch