compaq lte elite User Manual

The keylock assembly is replaceable. The blocker is integrated into the
bottom cover. To replace the blocker, the bottom cover must be replaced.
NOTE: In addition to the keylock assembly, the expansion base is designed
with a provision for an optional cable lock to secure the expansion
base to an immovable object (Section 6.9).
Horizontal Guides 

Two horizontal guides [1] located at the front of the docking bay (Figure
6-17) help align the computer in the expansion base. The horizontal guides
engage in the grooves that are located between the upper and lower halves
of the computer [2]. The guides also prevent the computer from being
vertically removed while it is docked in the expansion base to prevent
damage to the connectors and to provide additional security.
6.7 Running Computer Setup 
The first time you dock the computer in the expansion...

1. Turn on or reboot the system.
2. Press the F10 key as soon as the cursor moves to the upper-right corner
of the screen.
3. When prompted, select the desired language.
4. Select Computer Setup from the Configuration and Diagnostics menu.
5. Follow the instructions on the screen.
Running Computer Setup from a Compaq LTE Lite
If you are using a Compaq LTE Lite in the expansion base, run Computer
Setup from the Compaq Diagnostic diskette included with the SmartStation
Adapter. Do not run Computer Setup...

o Override blocker to prevent unauthorized manual undocking of the
computer
o Horizontal guides to prevent vertical removal of the docked computer
o A slot provided for an optional cable lock to lock the expansion base to
an immovable object (Figure 6-18)
Refer to Section 6.6 for more information on the keylock assembly, the
override blocker, and the horizontal guides.
NOTE: The cable lock, Kensington MicroSaver Security System Model 64068
(Figure 6-18), is available from Kensington Microware Limited or...

Chapter 7 - Compaq SmartStation Troubleshooting 
 
Introduction 
This chapter contains troubleshooting tables that provide a quick reference
for diagnosing problems with the SmartStation. It includes EXTDSK.SYS error
messages (Section 7.2) that may occur when the Compaq LTE Lite is docked.
To troubleshoot the SmartStation, complete the following steps:
1. Go to the troubleshooting table that covers the type of problem you are
encountering.
NOTE: Since symptoms can appear to be similar, carefully compare...

install optional devices, the computer may detect a configuration
change and prompt you to run Computer Setup. (Section 6.7).
o Verify that all required device drivers are installed.
o Verify that all required changes have been made to the CONFIG.SYS file.
o Verify that all required changes have been made to the AUTOEXEC.BAT file.
o Verify that printer drivers have been installed for each application.
o Determine whether an external device or its cable is responsible for the
problem by running POST with...

The spare battery pack Remove the spare battery
is not making proper pack, inspect the battery
contact with the charging compartment for
battery charger. any obstructions, then
reinsert it.
--------------------------------------------------
The spare battery pack Replace the spare battery
does not hold a charge pack.
and has reached end of
usefulness.
--------------------------------------------------
The spare battery pack Replace the spare battery
internal fuel gauge pack.
circuit is
inoperative....

is not attached or is contacts board is
damaged. attached properly to
the expansion base
system board.
2. Ensure that none of
the wires on the
battery contacts board
cable are damaged or
disconnected from the
rest of the cable. If
they are damaged or
disconnected, replace
the battery contacts
board. Route the cable
properly to ensure
that damage does not
reoccur (Section
9.14).
--------------------------------------------------
The battery contacts are 1. Ensure that all
damaged. battery contacts
are...

circuit board by
removing the card
cage and pushing
the power supply
connector down. If
the connector is
loose, replace the
power supply.
--------------------------------------------------
The motor is not in the Press the eject button
unloaded position. to reset the motor to
the unloaded position.
--------------------------------------------------
There is physical Undock the computer by
interference. pressing the eject
button. If the
computer does not
undock, remove the
computer using the
manual eject...

---------------------------------------------------------------------------
The motor does not Docking mechanism sled 1. Ensure that the
engage and no beep is is not interrupting the external options
emitted. computer-present sensor. door on the rear
panel of the
computer is open.
2. Ensure that the
computer-present
sensor is vertical.
Ensure that the
flag on the docking
mechanism sled goes
past the center of
the sensor when the
mechanism is pushed
all the way back.
If required, gently
bend the sensor...