compaq lte elite User Manual

3. Insert the lower edge of the LED cable assembly [1] into the lower slot
of the LED cable assembly bracket (Figure 4-53).
4. Rotate the top edge of the LED cable assembly up and press gently at the
top corners [2] (Figure 4-53) to snap it into the bracket.
IMPORTANT: Both sides of the LED cable assembly must be pressed
simultaneously to allow the assembly to snap into the
bracket. 

5. Reassemble the rest of the computer by reversing steps 1 through 16 of
Section 4.17.
4.19 Computer Base Enclosure 
To remove the computer base enclosure, complete the following steps:
1. Remove the system board and I/O bracket (Section 4.17).
2. Remove the LED cable assembly (Section 4.18).
3. Remove the I/O connector cover.
The computer base enclosure remains and includes the following items:
o Battery pack release latch assembly (Section 4.21).
o Hard drive release latch assembly (Section 4.21).
o...

NOTE: The I/O connector cover, Automobile Adapter door, and hard drive
compartment door are available in the Doors Kit (Table 3-9).
4.20 PCMCIA Compartment Door 
The PCMCIA compartment door comes installed on the computer base enclosure.
The door and spring are also available separately in the Doors Kit
(Table 3-9).
Removing the PCMCIA Compartment Door
To remove the PCMCIA compartment door, complete the following steps:
1. Open the door.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>

Replacing the PCMCIA Compartment Door
To replace the PCMCIA compartment door, complete the following steps:
1. Position the door spring [1] over its retaining post [2] on the computer
base enclosure (Figure 4-55).
2. Position the long end of the spring [3] into its slot on top of the
computer base enclosure (Figure 4-55) so that it stays in place.
NOTE: The spring automatically goes into place when the door is
installed and closed. 

3. With the door held in the fully open position, install the back hinge of
the door [1] onto its post on the computer base enclosure (Figure 4-56).
4. Slightly flexing the door, replace the front hinge of the door [2] onto
its post on the computer base enclosure (Figure 4-56). 

4.21 Battery Pack/Hard Drive Release Latch Assemblies 
This section covers removal and replacement procedures for the battery pack
release latch assembly and the hard drive release latch assembly. Each
assembly includes the following:
o Release button
o Latch
o E-clip
o Latch spring
The release buttons, latches, and latch springs work together as assemblies
to release the battery pack and hard drive. The parts for the battery pack
release latch assembly (located in the right side of the computer) are...

Removing the Release Latch Assembly
To remove either the battery pack or hard drive release latch assembly,
complete the following steps:
1. If you are removing the hard drive release latch assembly, remove the
hard drive (Section 4.12).
2. Remove the keyboard cover (Section 4.7).
3. Remove the keyboard (Section 4.10).
4. Remove the latch spring [1] by holding it with needle-nosed pliers near
its wide end and pulling it straight up out of its slot (Figure 4-57).
5. Remove the e-clip [2] that holds the...

Replacing the Release Latch Assembly
IMPORTANT: The parts for the battery release latch and hard drive release
latch assemblies are similar in appearance. However, note that
the battery latch is color-coded white, and the hard drive latch
is color-coded black. Be sure to use the correct set of parts
for this procedure.
To replace the release latch assembly, complete the following steps:
1. Replace the release button [1] (Figure 4-58).
2. Replace the latch [2] by sliding the latch onto its post (Figure...

attached to the enclosure. Leave the existing latch spring installed unless
it is defective.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

Chapter 5 - Compaq LTE Elite Specifications 
 
Introduction 
This chapter covers the following specifications of the Compaq LTE Elite
Personal Computer:
o Computer models
o Physical and environmental
o Memory expansion
o Display
o Diskette drive
o Hard drive
o Internal AC-to-DC power supply
o DC-to-DC power supply
o Battery pack
5.1 Computer Models 
Compuer Model Specifications
===========================================================================
Internal
Model Display Processor Cache RAM Hard...