compaq lte elite User Manual

The manual eject The override blocker Ensure that the
override bracket cannot move freely. override blocker can
cannot be accessed. move freely in the
(Bracket is not bottom cover. If it
visible through its cannot move freely,
slot.) ****** replace the bottom
cover.
--------------------------------------------------
The manual eject override 1. Straighten the
bracket is bent. manual eject
override bracket.
2. Replace the
docking mechanism....

replace the bottom
or top cover
(whichever
applies).
--------------------------------------------------
Plastic latches are worn Ensure that the
off of the bottom cover. plastic latches are
not worn off. If they
are, replace the
bottom cover.
===========================================================================
Table 7-4. Hardware Installation Problems
===========================================================================
Problem Probable Cause Recommended Action(s)...

--------------------------------------------------
The signal and/or power Determine if the
cable of the new device is signal and/or power
defective. cable is defective
by connecting another
cable.
---------------------------------------------------------------------------
The system locks up Switch 3 on the vertical Change Switch 3 to
when a backup to tape circuit board is the tape/diskette
is attempted. incorrectly set. drive installed
position (the
on/closed position)....

plastic switch
components
(Section 9.18).
3. Reassemble the
expansion base,
allowing the
switch board to
hang out from the
side of the unit
for test purposes.
4. Ensure that the
operating
condition of the
expansion base is
such that the LED
should turn on.
5. If the LED does
not turn on,
replace the cable
harness.
--------------------------------------------------
The cable harness (power 1. Reseat the cable
switch cable harness or harness.
eject switch cable 2. Replace the cable
harness) * is defective...

switch components
(Section 9.18).
3. Reassemble the
expansion base,
allowing the power
switch board to
hang out from the
side of the unit
for test purposes.
4. Ensure that the
operating
condition of the
expansion base is
such that the
power switch is
functional.
5. Press the power
button that is
mounted directly
on the power
switch board.
6. If the expansion
base and computer
power up, replace
the plastic power
switch components.
7. If the expansion
base and computer
do not power up,
replace the
power...

The expansion base and The computer is not Ensure that there is
computer do not power completely docked in no gap between the
on when either power the expansion base. expansion base and
switch is pressed, but the rear of the
a beep is emitted from computer. (Refer to
the expansion base and Table 7-2 for more
there is some LED information on
activity. solving docking
problems.)
--------------------------------------------------
The computer is not 1. Remove the
powering on properly. computer from the...

o The internal cable connector is not reversed.
o All SCSI devices are SCSI-2 compliant.
For more troubleshooting information, refer to the system messages and
troubleshooting sections of the Compaq EZ-SCSI Software Reference.
For information on using SCSI-2 devices, installing SCSI-2 device drivers,
and installing an internal SCSI-2 drive in the Compaq SmartStation, refer
to Appendix F.
7.2 EXTDISK.SYS Error Messages 
The EXTDISK.SYS external drive device driver is required for the Compaq LTE
Lite to...

no setting for
single, set the
jumper switches to
master.
---------------------------------------------------------------------------
Time-Out on Disk 1 The power or signal cable Ensure that the power
Secondary controller is not properly connected and signal cables are
EXTDISK not installed to the drive. properly and securely
connected.
--------------------------------------------------
Incorrect version of Install the version
EXTDISK.SYS. of EXTDISK.SYS
included with the
SmartStation Adapter....

Chapter 8 - Compaq SmartStation Illustrated Parts Catalog 
 
Introduction 
This chapter provides illustrated parts breakdowns and identifies the spare
parts for the Compaq SmartStation expansion base.
Refer to Chapter 3 for spare part information for the Compaq LTE Elite.
8.1 Enclosures 
Table 8-1. Enclosures
===========================================================================
Description Spare Part Number
===========================================================================
1. Bottom cover...

---------------------------------------------------------------------------
3. Drive Cage
Includes configuration label ** 198992-001
---------------------------------------------------------------------------
4. Top Cover 199002-001
---------------------------------------------------------------------------
5. Monitor Support Cover 137948-001 *
---------------------------------------------------------------------------
* Not shown
** Drive cage is interchangeable for drive position 1 or 2....