compaq lte 5000 User Manual

3. Remove the latch screw as shown in Figure 5-47. The release drops out
but the spring holds the latch in place. Use forceps or needle-nose
pliers to remove the latch and spring.
Chapter 5.10 Fan 
The cooling fan is mounted at the air vent on the left side of the
computer and is plugged into the system board. After removing the CPU
cover, the fan is easily removed by disconnecting the fan cable from the
system board and lifting the fan out (Figure 5-48). To remove the fan,
complete the following steps:...

4. Lift the fan out of the computer.
Reverse the above procedure to install a fan. Make certain the fan is
properly oriented with the label on top and the airflow arrow pointing out
of the computer.
Chapter 5.11 Processor Board 
To remove the processor board, complete the following steps:
1. Remove the CPU cover as described in Section 5.5.1.
2. Remove the status panel as described in Section 5.6.
3. Remove the display assembly as described in Section 5.8.1.
4. Remove the memory expansion board as...

8. Disconnect the thermistor cable [1] as shown in Figure 5-50. 

9. Remove the screw [2] from the right rear corner of the processor board
(Figure 5-50).
10. Remove the processor board as shown in Figure 5-51. 

Before installing the processor board, verify that the display jumpers are
appropriately configured for the type of display installed in the
computer. The jumper locations are shown in Figure 5-52, and jumper
configurations are presented in Table 5-1. 

Table 5-1. Display Configuration Jumpers
===========================================================================
Display Type JP3 JP2 JP4
===========================================================================
LTE 5000 10.4 in VGA CSTN 1-2 2-3 1-2
LTE 5000 10.4 in VGA CTFT 2-3 2-3 1-2
LTE 5000 11.3 in SVGA CSTN 1-2 2-3 2-3
LTE 5100 10.4 in SVGA CTFT 2-3 2-3 2-3
LTE 5150 Rev. 4.X * 11.3 in 1-2 1-2 1-2
SVGA CSTN
LTE 5150 Rev. 2.X * 11.3 in 2-3 1-2 1-2
SVGA CSTN
LTE 5200 10.4 in SVGA CTFT 2-3 2-3...

CTFT
LTE 5400 12.1 in 1024x768 2-3 2-3 2-3
CTFT
---------------------------------------------------------------------------
* Verify the display panel revision number by checking the printed number
on the large ferrite bead on the display cable. The display cable is
located on the left side of the display assembly.
===========================================================================
Reverse the above procedure to install a processor board, taking care with
the placement of the EMI shield (Figure...

Chapter 5.13 Power Board 
To remove the power board, complete the following steps:
1. Remove the processor board as described in Section 5.11.
2. Remove the screw near the hard drive bay (Figure 5-55) and lift the
power board out of the computer. 

Reverse the above procedure to install a power board.
Chapter 5.14 System Board 
To remove the system board, complete the following steps:
1. Remove the CPU panel as described in Section 5.5.1.
2. Remove the display as described in Section 5.8.1.
3. Remove the processor board as described in Section 5.11.
4. Remove the power board as described in Section 5.13.
5. Remove the insulator laying on top of the system board if it is damaged
(Figure 5-56). It is not necessary to remove the insulator to remove...

6. Remove the standoff from the left rear corner of the system board
(Figure 5-57).