Comdial Solo II Attendant Position User Guide

CONFERENCE @AUS 
Multiline Conference for 2 external parties and 1 internal party 
NOTE: Conference transmission levels are not compensated 
and connections of parties must be supervised by one inside 
parly. 
a Establish first outside call and press HOLD. 
e Establish second outside call. 
@ Press and hold down line key for second call. 
e Press line key for first call. 
o Release both line keys. Conference is established. 
To selectively disconnect one member of the conference, 
e Press line key of...

To drop intercom party from conference, 
l Intercom called party can hang up handset. 
-OR- 
l Press line key of line to be saved (the other line will be auto- 
matically disconnected). 
8  

FEATURE OPERATION 
Solo II feature operations can be performed over the direct-con- 
nected lines that are supervised by the Solo II Attendant Postion 
and over the Solo-to-Solo intercom line. 
LINE MONITORING 
Handsfree dial a number, 
o Press line key. 
l Dial number. 
e Monitor call ringing. 
l Lii handset when party answers. 
To activate line monitoring while on a call, 
l Press MONITOR. 
l Hang up handset. 
NOTE: Useful when a party places you on hold. You- can 
monitor until caller’s return, then...

line is stored, the station automatically chooses the Iasf line 
that was used. If the last line used is busy, the station aufo- 
maficalty selects the idle line preference (If one is assigned). 
If the idle line preference is busy or unavailable, press a line 
key and make the auto dial selection again. 
To program numbers, 
e Press ITCM. 
e Press SAVE. Listen for tone. 
0 Press desired key (in memory key field) for autodial locations 
l-20 (level 1). Tone will stop. 
-OR- 
0 Press HOLD key, then memory...

REDIALING 
Saved Number Redial 
The last number dialed can be saved for redial at anytime. 
To save number, 
0 Press SAVE, during or after the call. 
To dial saved number, 
0 Press 
HOLD key. 
Q Press SAVE key. 
0 When party answers, 
0 Lift handset. 
To cancel, 
8 Press 
MONITOR. 
Last Number Redial 
The last number previously dialed can be redialed auiomBtically 
stored to replace a previously stored number, A special key is 
provided for the Bast number. 
NOTE: If the REDML key must be programmed for...

If on line listening to busy tone or no answer, 
l Press REDIAL key twice. 
l If using handset, pause a few seconds and hang up. 
-OR- 
. If using speakerphone, station will automatically hang up. 
l Station will redial number once a minute for IO minutes. 
When party answers, 
l Lift handset. (If on speakerphone, press MONITOR key or 
station will hang up.) 
To cancel call and automatic redial action, 
0 Lift and replace handset during ringing. 
To cancel between call attempts, 
0 Press REDIAL 
key...

If your system has been configured for recall, 
l Press TAP to disconnect (as if you had hung up), and obtain 
a new dial tone for another call. 
NOTE: System can be configured for recall or tap, but not 
/ for both. 
POSITIVE DISCONNECT/RECALL 
l If the hookswitch in the handset cradle is pressed and 
released while the handset is off-hook, a timed disconnect of 
the active line is performed. This feature retains the dial tone 
recall feature for use on stations where the 
TAP key is 
programmed to...

MUTE 
To prevent other party from hearing, 
l Press MUTE (monitor light flutters). 
0 Press MUTE again to resume conversation (monitor light 
turns off). 
MESSAGE WAITING 
For internal system messaging, the message betweensolo sta- 
tions, waiting light of one station is controlled by another sta- 
tion designated as the Message Center by programming. 
NOTE: The message waiting light is located directly above 
the HOLD key. 
To turn station message waiting light on, 
l Press 9 (idle intercom line...

STATION DIRECTORY 
A pull-out shelf contains a paper station directory card which 
can be used to store identifications as follows: 
l Level 2 autodial identification for locations 21-40. 
l Speed dial identification locations for locations 1-O. 
NOTE: The identification for the level 1 auto dial locations 
7-20 should be placed on the station index card (located be- 
tween the memory keys) along with the identification of sta- 
tion select key. 
USING THE DATAPORT 
(Auxiliary jack located on back edge...

This manual has been developed by Comdial Corporation (the “Company”) 
and is intended for the use of its customers and service personnel. The infor- 
mation in this manual is subject to change without notice. While every effort 
has been made to eliminate errors, the Company disclaims liability for any 
difficulties arising from the interpretation of the information contained herein. 
The information contained herein does not purport to cover all details or varia- 
tions in equipment nor to provide for...