Comdial Executech 1432 KSU Instructions Manual

IMI 66-036 
Programming 
Station COS - continued 
22 Specify flexible key/function assignment 
(non-square configuration), if required. 
3 AND 8 LINE KEYSET 
0 Press program key B6 
l Press program keys Bl - B8 to choose line keys 1 - 8 
- Fast tone bursts will sound 
0 Press program keys Al - Al4 to assign lines 1 - 14 
-or- 
0 Press RECALL key to disable line appearance 
- Tone bursts stop 
0 Repeat for each line assigned 
22 LIHE/FEATUKE KEYSET 
0 Press program key B6 
Assic,ln Lines To Keys 
--.-_ -...

IMI 66-036 Programming 
Station COS - continued 
23 
24a 
24b 
25 
26 Press * 
Choose next station port for programming 
l Press program key B8 
l Press console keys Cl0 - C41 
-or- 
Block program a group of stations with same COS as previously 
programmed 
station+ 
0 Press * HOLD 
0 Press program key (Cl0 - 
0 Press program 
key (Cl0 - C41) to specify model station port 
~41) to specify first station in block 
0 Press program key (Cl0 - 
Note: Flexible C41) to specify last station in block....

IMI 66-036 
STATION ID (REF SYSTEM COS CHART) 
l Shading denotes line default conditions. 
l Check off or enter the values chosen for 
the lines being programmed. STATION ID (REF. SYSTEM COS CHART) 
BASELEVEL@~~(gq)(6 
STATION PROGRAMMING MODE @ 
.- . . 
@ 
RlNGlNG 
c-7 DELAYED RINGING  c.3 
RINGING 
ON ALL LINES FOR STATtONS V3.17.39. AND 4,. 
15-18 
I 
20 
Programming 
@I RESERVE INTERCOM LINKS 
NONE 1 1 2 3 4 1 5 1 6 1 7 
0 [o lo~olololo~o 
PRESS 0 TO CONTINUE 
Change Page 12187 
* Feature not...

IMI 66-036 Programming 
COS AND 
SMDK PRINTOUT 
COS PRINTOUT 
LJhen a data printer is connected to the system, it can be commanded, 
from station port 10 or 11, to print the class of service (COS) 
programming configuration. Partial or complete printouts can be 
obtained. When the printer is being used to obtain a COS printout, 
the 
Station Message Detail Recording (SMDR) function is temporarily 
halted. 
SMDR data collection is continued by the system during a COS 
printout operation; however, if more...

40 COLUMN 
PRINTOUT 
LINES 7 STATION NUMBER 
LINE NUMBER 
(SEE NOTE2) 
1 
2 
_ [CARRIAGE 
RETURN 
[CARRIAGE ) 1 LINE FEED 1 
x RETURN 1 
-1 
(;’ 
f: DIALED DIGITS-UP TO MAXIMUM OF 32 
(ACCOUNT CODES ARE ISOLATED BY * OR # SYMBOLS 
NOTES 
1. CARRIAGE RETURN AND LINE FEED IMMEDIATELY 
FOLLOW LAST PRINTED CHARACTER ON EACH LINE. 
ALSO SEE NOTE 2 
2. ILLUSTRATED PRINTOUT IS40 COLUMN, TWO-LINE 
FORMAT. ON 80 COLUMN ONE-LINE PRINTOUT 
FORMAT, CARRIAGE RETURN AND LINE FEED 
CHARACTERS AT END OF LINE 1 ARE...

IMI 66-036 Programming 
CASSETTE TAPE RECORD OF COS VALUES .* 
: 
0 Connect audio cassette tape recorder to music interface on side of 
KSU. 
0 Do not perform other programming action while tape system is active. 
l If the system includes a data printer, appropriate response messages 
will be printed during the recording and loading of COS data. 
RECORDING COS 
DATA TO TAPE’ 
-_------- --- --- -- - 
To record currently stored COS program values on cassette tape for 
later use, proceed as follows: 
1....

IMI 66-036 
Programming 
SYSTEM CLOCK INFORMATION 
All 
clock setting and adjustment must be performed from station port 
10 or 11. 
SETTING 
THE CLOCK 
1. 
Press ITCM 
, then dial * 
# 
2. Dial the 
clock date with the key pad keys 
YEAR MO!ATti DAY 
HOUR MINUTE 
NOTE 
Values less 
than 10 must be dialed as OX. 
Hours 
must be expressed in the 24-hour format. 
3. 
If tne SMDR printer is installed and operating, the 
clock date 
will 
be printed as follows. 
** Ol/ut1/86 16:OU (Example) 
4. Reset the...

IMI 66-036 
Programming 
SYSTEM SPEBD DIAL PROGRAMMING 
Pifty (50) 
system speed dial numbers can be stored from station port 
lU or 11 for use at all stations in the system. 
System speed dial 
numbers will not be toll restricted unless specified by station COS 
programming. 
* Press ITCM * 
* Press 
SAVE 
* Dial storage location (10 - 59) 
* Choose line or group preselection 
(multifunction (hybrid) system only) 
* Dial 1 - 
4 for group 
-or- 
* Press a line 
key for line 
Note: 
Key-to-line assignment...

IMI 66-036 Programming 
E/ PROGRAM ENTRY 
SYSTEM COS TOLL TABLES 
1 I I I I I 
I 
Q 
r-- TO RETURN 
TO BASE 
LEVEL 
SPECIFY 
TIME: 
I 
ED 
TO RETURN 
TO BASE 
LEVEL 
SPECIFY 
TIM: SPECIFY 
TIME: 
Q 
TO RETURN 
TO BASE 
LEVEL 
NOTE 1: NNCllON NOT AVAILABlE ON MOE1 1432 KSU REV. A THROUCH M 
Figure 3-3. 
Change Page 12/87 
BAUD RATE 
Q: I IO @ad 
CD 150 Baud 
a: 300 Bold 
@rJ: 600 Bad 
a: I200 Baud 
~:2400 Baud 
@D:3600 Eh”d 
~~4800 Bo”d 
CD9600 Baud 
a:19200 &ud 
Q TO RETURN 
TO BASE 
LEVEL 
TOLL 
TABLES...

programming reference chart - continued Programming 
=I PROGRAM ENTRY 
LINE COS 
SPEC I FY 
TYPE 
GROUP: 
Q:NONE 
@I:GPi 
@:GPZ 
@:GP3 
@3=GP4 
MODE: 
@:PULSE 
@= TONE 
PRIVACY RLS: 
@:DISA@LED 
@:ENABLED 
TOLL TABLES: 
@:ERASE 
a,Qz 
TA&ES I-16 
ABANO HOLD 
ALS: 
@I:300 MS 
m:so MS 
ED 
II TO RETURN 
TO BASE 
LEVEL 
Change Page 12l87 
L 
STATION COS 
PRINTUU 
Q -PA PORT 
Q :VOlCE BLOCK 
Q) :EXECUTIVE OVERRIDE 
@ :SYSTEM SPEED DIAL 
Q) :AUTO HOLD TOLL RESTRICT 
@.D:h+SG. WAIT ORIG. 
a$?D,a @MING TONE 122...