Comdial Executech 1432 KSU Instructions Manual

							IMI 66-036 
Programming 
Station COS - continued 
22 Specify flexible key/function assignment 
(non-square configuration), if required. 
3 AND 8 LINE KEYSET 
0 Press program key B6 
l Press program keys Bl - B8 to choose line keys 1 - 8 
- Fast tone bursts will sound 
0 Press program keys Al - Al4 to assign lines 1 - 14 
-or- 
0 Press RECALL key to disable line appearance 
- Tone bursts stop 
0 Repeat for each line assigned 
22 LIHE/FEATUKE KEYSET 
0 Press program key B6 
Assic,ln Lines To Keys 
--.-_ - --- -- 
0 Press key to be assigned (A or B field) - Fast tone bursts sound 
l Press program keysA1 - Al4 to assign lines 1 - 14 
- Tone bursts stop 
l Repeat for all keys requiring line appearance 
Disable Line A&earance At Keys (clears any prior assignment) 
------- --- 
0 Press key to be-d&nred sppearance - Fast tone bursts sound 
0 Press RECALL key - tone bursts stop 
0 Repeat procedure for all required key locations 
0 Press key to be assigned (A or B field) - Fast tone bursts sound 
l Press program keys Cl0 - ~41 to choose station ports 10 - 41 
- Tone bursts stop 
0 Repeat for all keys requiring DSS assignment 
Assign Autodial To Keys (clears any prior assignment) 
--I_ - --.---- .-- 
0 Press key to be assigned (A or B field) - Fast tone bursts sound 
l Press RECALL 
Key - tone bursts stop 
l Repeat procedure as required for all autodial keys 
Assign_ O&nar,lic Loos 
Keys (clears any prior assignment)* 
--- 
@ Press 
kef-gi, ET; or 83 
- Fast tone bursts sound 
l Press KECALL key - tone bursts stop 
l Repeat for B2 and 83 if required 
* Feature not available on Model 1432 ‘KSU Rev. A through M. - continued 
Change Page W87 3-14  
						

							IMI 66-036 Programming 
Station COS - continued 
23 
24a 
24b 
25 
26 Press * 
Choose next station port for programming 
l Press program key B8 
l Press console keys Cl0 - C41 
-or- 
Block program a group of stations with same COS as previously 
programmed 
station+ 
0 Press * HOLD 
0 Press program key (Cl0 - 
0 Press program 
key (Cl0 - C41) to specify model station port 
~41) to specify first station in block 
0 Press program key (Cl0 - 
Note: Flexible C41) to specify last station in block. 
key/function assignments for station port 10 or 11 
cannot be changed by block programming. 
If block programming of step 24b is not performed, repeat steps 
5 through 24a for each station in system. 
Press * MONITOR 
to exit programming. 
*Feature not available on Model 1432 KSU Rev. A through M. 
- end 
Change Page KY87 3-15/3-16  
						

							IMI 66-036 
STATION ID (REF SYSTEM COS CHART) 
l Shading denotes line default conditions. 
l Check off or enter the values chosen for 
the lines being programmed. STATION ID (REF. SYSTEM COS CHART) 
BASELEVEL@~~(gq)(6 
STATION PROGRAMMING MODE @ 
.- . . 
@ 
RlNGlNG 
c-7 DELAYED RINGING  c.3 
RINGING 
ON ALL LINES FOR STATtONS V3.17.39. AND 4,. 
15-18 
I 
20 
Programming 
@I RESERVE INTERCOM LINKS 
NONE 1 1 2 3 4 1 5 1 6 1 7 
0 [o lo~olololo~o 
PRESS 0 TO CONTINUE 
Change Page 12187 
* Feature not available on 
Model 1432 KSU Rev. A through M. 
3-1713-18  
						

							IMI 66-036 Programming 
COS AND 
SMDK PRINTOUT 
COS PRINTOUT 
LJhen a data printer is connected to the system, it can be commanded, 
from station port 10 or 11, to print the class of service (COS) 
programming configuration. Partial or complete printouts can be 
obtained. When the printer is being used to obtain a COS printout, 
the 
Station Message Detail Recording (SMDR) function is temporarily 
halted. 
SMDR data collection is continued by the system during a COS 
printout operation; however, if more than two calls are logged for any 
one line, call records may be lost. 
1 Press ITCM * 7 4 6 
* (base level entry if not active) - 
2 Press program key 36 
3 Choose desired printout 
* Press program key per chart. Printout begins immediately. 
PRINTOUT PROGRAM KEY 
All COS 
84 
System COS B5 
Line COS B6 
Toll Tables 07 
All Station COS 88 
One Station COS Cl0 - c41 
(to choose station port) 
I 4 To stop printout, 
On Model 1432 KSU Rev. A through M: press * B7 
On Model 1432 KSU Rev. N and later: press 83. 
5 Press * MONITOR (ends procedure) 
SMDR PRINTOUT 
The SMDR printout data is provided automatically as it is generated. 
No intervention is required to obtain the printout. 
The data is 
formatted as shown in Figure 3-2. 
obtained from any KSU revision. Two IO-column printout lines can be 
One 80-column printout can be 
obtained from KSU Rev. N or above. 
Change Page 12/07 
3-19  
						

							40 COLUMN 
PRINTOUT 
LINES 7 STATION NUMBER 
LINE NUMBER 
(SEE NOTE2) 
1 
2 
_ [CARRIAGE 
RETURN 
[CARRIAGE ) 1 LINE FEED 1 
x RETURN 1 
-1 
(;’ 
f: DIALED DIGITS-UP TO MAXIMUM OF 32 
(ACCOUNT CODES ARE ISOLATED BY * OR # SYMBOLS 
NOTES 
1. CARRIAGE RETURN AND LINE FEED IMMEDIATELY 
FOLLOW LAST PRINTED CHARACTER ON EACH LINE. 
ALSO SEE NOTE 2 
2. ILLUSTRATED PRINTOUT IS40 COLUMN, TWO-LINE 
FORMAT. ON 80 COLUMN ONE-LINE PRINTOUT 
FORMAT, CARRIAGE RETURN AND LINE FEED 
CHARACTERS AT END OF LINE 1 ARE REPLACED BY 
TWO SPACES FOLLOWED BY ENTlRE CONTENTS OF 
LINE 2. ALSO SEE NOTE 3 
I@? 3. _ 
AN 80 COLUMN ONE-LINE PRINTOUT IS ONLY 
AVAILABLE ON KSU REV. NAND ABOVE. 
4. OUTGOING CALL MUST BE OFF-HOOK FOR 20 
SECONDS MINIMUM OR NO RECORDING OCCURS. PRINTOUT EXAMPLES 
UNANSWERED INCOMING CALL 
1 12/05/86 1651 
NOANS 0.6 
ANSWERED INCOMING CALL 
16 1 
12/05/86 1652 
1.6 0.2 
ANSWERED INC-“.-‘- - -. 
XJMINti GALL .- -- 
(WITH CALLER ID ADDED BY 
1 24 1 12/05/86 1~53 1.2 0.2 
“1234 
STATION DURING CALL) 
OUTGOING CALL (LOCAL) 
16 2 12/05/86 
1658 
2.0 
9782200 
OUTGOING CALL 
(WITH ACCOUNT CODES) 24 2 12/05/86 17:Ol 
.5 
11233456789’0#‘7412580#9631*# 
AC POWER FAILURE AND 
RESTORATION 
OFFTIME 
l * 
12/05/86 17:03 l . 12/05/86 17:08 I  
						

							IMI 66-036 Programming 
CASSETTE TAPE RECORD OF COS VALUES .* 
: 
0 Connect audio cassette tape recorder to music interface on side of 
KSU. 
0 Do not perform other programming action while tape system is active. 
l If the system includes a data printer, appropriate response messages 
will be printed during the recording and loading of COS data. 
RECORDING COS 
DATA TO TAPE’ 
-_------- --- --- -- - 
To record currently stored COS program values on cassette tape for 
later use, proceed as follows: 
1. Install blank cassette tape, 
and prepare recorder for recording. 
2. Cause recorder to begin recording blank cassette tape from 
beginning. 
I 3. Press ITCM * 7 4 6 * 
4. Press ITCM B4 to start recording process. 
5. To abort procedure (if required), 
*Press ITCM * 7 4 6 * ITCM 
0 Press program key B8. 
COS recording requires approximately 12 minutes. 
Station port 10 or 
11 will ring when recording is complete. 
To load previously recorded COS program values into system to replace 
current program values, proceed as follows: 
1. Install pre-recorded cassette tape, 
and prepare recorder for 
playback 
I 2. 
Press ITCM * 7 4 6 * 
3. Press ITCM HOLD 
to load COS features. 
4. 
Start tape playback. 
5. To abort the procedure (if required), 
l Press ITCM * 7 4 6 * ITCM 
0 Press program key B8. 
COS loading requires approximately 10 minutes. 
will ring when loading is complete. Station port 10 or 11 
Change Page 12/W 3-21  
						

							IMI 66-036 
Programming 
SYSTEM CLOCK INFORMATION 
All 
clock setting and adjustment must be performed from station port 
10 or 11. 
SETTING 
THE CLOCK 
1. 
Press ITCM 
, then dial * 
# 
2. Dial the 
clock date with the key pad keys 
YEAR MO!ATti DAY 
HOUR MINUTE 
NOTE 
Values less 
than 10 must be dialed as OX. 
Hours 
must be expressed in the 24-hour format. 
3. 
If tne SMDR printer is installed and operating, the 
clock date 
will 
be printed as follows. 
** Ol/ut1/86 16:OU (Example) 
4. Reset the 
minutes setting, if necessary, as follows: 
a. Repeat step 1. 
b. Dial the new minutes digits, and press the # key. 
C. 
A new clock date printing will occur. 
5. To obtain a printing of the current 
clock date, 
press ITCM * * # 
Printing will occur automatically once each 24-hour period. 
** MO/DY/YR 03:oi) (current date and 
0O:OO hours) 
PWIW INTHRRUPTION 
Tne system clock will continue to run for at least 
30 minutes after AC 
power has been removed from the system. 
If power is restored within 
the 30-minute backup period, 
the following printing sequence will 
occur: 
LAST VALID 
CLOCK = MO/DY/YH HR:MN 
(time of power outage) 
MO/DY/YR HR:MN 
(time of power return) 
If power is not restored within, the backup period, the following 
printing sequence will occur when the power is restored. 
CLOCK 
NOT VALID 
12/01/&6 0O:OO 
(default clock date) 
The clock will 
begin running from the default date. It must be reset 
to the current date per the instructions 
above. 
3-22  
						

							IMI 66-036 
Programming 
SYSTEM SPEBD DIAL PROGRAMMING 
Pifty (50) 
system speed dial numbers can be stored from station port 
lU or 11 for use at all stations in the system. 
System speed dial 
numbers will not be toll restricted unless specified by station COS 
programming. 
* Press ITCM * 
* Press 
SAVE 
* Dial storage location (10 - 59) 
* Choose line or group preselection 
(multifunction (hybrid) system only) 
* Dial 1 - 
4 for group 
-or- 
* Press a line 
key for line 
Note: 
Key-to-line assignment per programming arrangement. 
Refer to station COS programming reference chart 
for station port 10 key-to-line assignments. 
-or- 
* Dial 0 for no group or line preselection 
* Dial speed dial number (up to 32 digits) 
*Dial i-0, $I and * 
* Press HOLD 
to store 
pause if required 
* Press RECALL 
to store flash if required 
* Press 
SAVE 
and repeat procedure for each number. 
* Press 
PlON IIOR 
to end procedure 
SYSI’tif4 SPEED DIAL INDEX 
3-2313-24  
						

							IMI 66-036 Programming 
E/ PROGRAM ENTRY 
SYSTEM COS TOLL TABLES 
1 I I I I I 
I 
Q 
r-- TO RETURN 
TO BASE 
LEVEL 
SPECIFY 
TIME: 
I 
ED 
TO RETURN 
TO BASE 
LEVEL 
SPECIFY 
TIM: SPECIFY 
TIME: 
Q 
TO RETURN 
TO BASE 
LEVEL 
NOTE 1: NNCllON NOT AVAILABlE ON MOE1 1432 KSU REV. A THROUCH M 
Figure 3-3. 
Change Page 12/87 
BAUD RATE 
Q: I IO @ad 
CD 150 Baud 
a: 300 Bold 
@rJ: 600 Bad 
a: I200 Baud 
~:2400 Baud 
@D:3600 Eh”d 
~~4800 Bo”d 
CD9600 Baud 
a:19200 &ud 
Q TO RETURN 
TO BASE 
LEVEL 
TOLL 
TABLES 
@~-SINGLE 
LINE 
IHOTELI 
ISEE - 
NOTE I I 
Q4INGLE 
LINEIMMIN.1 
mm TO SELECT 
TABLE I-16 
m:DENY 
m:ALLow 
FOR TABLE 
TYPE 
aism FOR ENTRY 
l-4 
OGDFD IUP TO 16 
DIGITS1 
REPEAT 
RE&RED 
continued 
Programming Reference Chart 
3-25  
						

							programming reference chart - continued Programming 
=I PROGRAM ENTRY 
LINE COS 
SPEC I FY 
TYPE 
GROUP: 
Q:NONE 
@I:GPi 
@:GPZ 
@:GP3 
@3=GP4 
MODE: 
@:PULSE 
@= TONE 
PRIVACY RLS: 
@:DISA@LED 
@:ENABLED 
TOLL TABLES: 
@:ERASE 
a,Qz 
TA&ES I-16 
ABANO HOLD 
ALS: 
@I:300 MS 
m:so MS 
ED 
II TO RETURN 
TO BASE 
LEVEL 
Change Page 12l87 
L 
STATION COS 
PRINTUU 
Q -PA PORT 
Q :VOlCE BLOCK 
Q) :EXECUTIVE OVERRIDE 
@ :SYSTEM SPEED DIAL 
Q) :AUTO HOLD TOLL RESTRICT 
@.D:h+SG. WAIT ORIG. 
a$?D,a @MING TONE 122 LINE KEYSET ONLYI 
SELECT PRIME LINE:cHART KEY):LINE:OR 
@$I,. OR &&@I,,@,@ : TRUNK GROUPS I -4 
%I;;’ RINGING LINE PREF 
3 
@RINGING 
B~ELAYED RINGING 
i SELECT FEATURE 
E9t4 1 GHT TRANSFER - THEN 
@AUTO PRIV. RLS - SELECT LINES WITH 
@ACCESS DEN,ED - (SELECTION WAN KEY9 
@JORIG. DENIED - 
@IDLE LINE PREF. - 
@ ASS1 GN TOLL TABLES : ~-Q~@~~,@I:TABLEs I -16 
@DREsERvE lTc~ LINK: 
Q-~:~ELECT LINKS I -7 
-or- 
~D:NO RESERVED LlNK 
Q :TO CONTINUE 
a ‘ALL-CALL/ZONE PAGING:m:CLEARS ALL 
@J:ALL CALL ORIG. 
@3=ALL CALL REC. 
m,-a:ZONES l-3 ORIG. 
a)-a:ZONES l-3 REC. 
Q -TO CONTINUE 
@I -KEY MAPPING MOOE:lDEPENDENT UPON PHONE TYPE1 
PRESS KEY TO BE DEFINED THEN PRESS FUNCTION. 
m-0 :DSS/BLF 
Eicrp -BLANK AUTO01 AL 
B :OY:AMIC LOOP KEY FOR Bl,B2 8 83 ISEE NOTE I, 
- 
DEFAULT 
SPECIFY: 
Q?3STEM 
QD’LINE 
a: STAT I ON 
@%PULSE 
BD-TONE 
~DKEY MPPP~NG 
I I 
ONE STATI ON 
cEl 
t; TO RETURN 
TO ‘BASE 
LEVEL 
PRINTOUT 
Q 
n TO RETURN 
TO BASE 
LEVEL 
PORT IO: 
10 TO 41 FOR MODEL 1432 KSU 
NOTE 1: FINlYON NOT AVAILABLE ON MODEL 1432 KSU REV. A IHROUCH M 
3-26