Comdial Executech 1432 KSU Instructions Manual

							IMI 66-036 
Programming 
System COS programming procedure-continued 
10 Specify station type for each station port 
l Press console keys Cl0 - 
C41 to identify station port 10 - 41 
l Press console key to specify station type 
I C42 = 
Single-Line Keyset (administrative phone) 
RECALL = 
Single-Line Keyset (hotel/motel phone)* 
C46 = 
8 Line BLF Keyset 
c47 = 
DSS/BLF Console (40-key) 
C48 = 
3 and 8 Line Keyset 
c49 = 
I 22 Line/Feature Keyset 
Cl0 = 
32-Key Console (without call announce)* 
Keypad Key 6 = 
32-Key Console (with call announce)* 
Keypad Key 7 = LCD Phone* 
0 Press * 
and repeat steps for each active station port 
NOTE: The step 10 action sets STATION COS for IDed port to the DEFAULT 
conditions for that type of station. 
11 Press * 12 Press MONITOR to exit or proceed to next COS 
*Feature not available on Model 1432 KSU Rev. A through M. 
Change Page 12B7 3-6  
						

							IMI 66-036 Programming 
SYSTEM CdS PROGRAMMING REFERENCE TABLE 
l Shading denotes system default conditions 
l Check off values chosen for system being programmed 
BASE LEVEL (ITCM) (*i) a (4 a (*i) 
1 2 1 300 MkEC. ) 
3 ) 500 MSEC. 
1  4 
1 600 MSEC. 
( 
I 
Note: 0 program selection (dlsa- 
bled) enables exclusive hold condi- 
tion (when set at station) .to place 
line on hold that cannot be released 
at any other statlon. BAUD RATE FOR COS AND SMDR DATA 
t 
@ 80 COLUMN 1 LINE 
@ 40 
CdLLJMN 2 l&S 
6 
9 
STATION ADJUNCT PORT 
TYPE 
10 64311 
(c44)12 (c4913 
8 LINE ELF KEYSET 
N/A 1 
DSSlBLF CONSOLE . :’ 1 ,I .I 
Change page 12187 
* Feature not available on 
Model 1432 KSU Rev. A through WI. 
10 I Tnr 
STATION 
STATION PORT 
! @i-$ 
32-KEYCONSOLE W/OC.A. ! 1 
: 1 ( 
: ’ j ! 1 1 
i g 32.KEYCONSOLE WC.A. < I  / 1 : ; j / ; j I j ’ 
7 
LCD t’HONE 
I * 6 I I / 
3-7 
r- STATION PORT  
						

							I 
IMI 66-036 Programming 
TOLL RESTRICTION PROGRANMING 
In order for toll restriction to take effect, the following three-fold process must occur. 
l One or more toll tables must be entered. 
l Toll tables must be assigned to all appropriate lines. 
l Toll tables must be assigned to all appropriate stations. 
‘Only the toil table(s) which are entered and assigned to both a line and a station using that line 
will invoke any toll restriction. 
TABLE ENTRY PROCEDURE 
1. Determine the types of dialing restrictions which must be imposed on the system. Typically, - 
this includes access codes which result in toll charges, and certain local numbers as 
desired. 
2. If the restricted dialing codes will be imposed consistently on most or all stations in the 
system, list them on one or two tables. If wide variation in the dialing restrictions is planned, 
spread the listing out across several tables. 
3. Strategically group the listings on the tables so that a list of restrictions can be applied to a 
particular station or group of stations. 
4. Designate each table as a DENY table or as an ALLOW table. The numbers entered in a 
DENY table are prevented from being dialed. ALLOW tables take precedence over DENY 
tables. Therefore, an entry in an ALLOW table will provide an explicit exception to an entry in 
a DENY table. Note that the system a/ways permits the dialing of any number not explicitly 
denied. Also, system speed dial numbers will not be toll restricted unless specified by station 
COS programming. 
l Example A: 
Provide a simple and broad toll restriction format by creating a DENY table 
with two entries: Entry (1) = 1 Entry (2) = 0. This format prevents all long distance and 
operator calls. 
l Example B: 
Prevent the dialing of all numbers within the (804) area code, while allowing 
the dialing of one specific number within that area code, by entering 1804 in a DENY table 
and 18049782200 in an ALLOW table. Alternately, allow all numbers in the 978 exchange 
by entering 1804978 in an ALLQW table. 
5. Press the # key in place of a particular digit to condense a range of numbers into one entry. 
The # character is a “match-anything” digit, and can be included in an entry in either a DENY 
table or an ALLOW table. 
l Example A: 
If 357,377,387, and 397 dialing is to be prohibited, list one entry of 3#7 on a 
DENY table to cover them all. 
l Example B: 
Since area codes typically have a 1 or a 0 as a middle digit, prevent long 
distance calls to those area codes by entering l#l# and l#O# in a DENY table. 
6. Since it is important that emergency numbers never be restricted, always create an ALLOW 
table with entries of 911 and 1911 to override any DENY tables that have been created. 
7. If the system is installed behind a PBX, include an access code as part of every table entry. 
8. Once these tables are completely filled out, enter the restriction planning tables on the line, 
and station programming reference charts to record the planned toll restrictions for the 
system. 
3-8  
						

							IMI 66-036 
Programming 
1 
2 
3 TOLL RESTRICTION PROGRAMMING PROCEDURE 
Press ITCM * 
7 4 6 * 
(base level entry if not active) 
Press program key B4 (enter toll program mode) 
Press console key Cl0 - 
~25 to select table number (1 - 16) 
4 
6 
6 
10 Sele 
ct table type 
l ; De 
l:, - press program key 85 5 Select table entry l Al l 
Press program key Al - A4 
- press program key B6 
tP select entry 1 - 4 
Dial number (16 digits max.) KEY Al A2 A3 A4 
ENTRY 1234 - 
(Press # for 
digit) match anything 
7 Repeat steps 5 and 6 
until all numbers are 
Repeat steps 3 through 7 until 
all 
tables are programmed programmed in table. 
9 Press * 
Press MO.NITOR 
to exit or proceed to next COS programming step. 
TOLL RESTRICTION PROGRAMMING REFEREICE TABLES 
TYPE: ALLOW DENY 
TABLE ASSIGNMENT: LINES __ STATIONS 
RESTRICTION TABLE 3 
DENY 
TYPE: ALLOW RESTRICTION TABLE 4 
.i 
DENY 
TYPE: ALLOW DENY v 
1 TABLE ASSiGNMENT: LINES - 
STATIONS 
I 3 
I I 
4 
TABLE ASSIGNMENT: LINES - STATIONS 
3-9a  
						

							IMI 66-036 Programming 
Toll restriction tables-continued 
r ’ RESTRICTION TABLE 7 
TYPE: ALLOW ,’ DENY ~ 
I I , I , I I I 4 
TABLE ASSIGNMENT: LINES __ 
STATIONS 
RESTRICTION TABLE 9 
TYPE: ALLOW - DENY ___ 
TABLE ASSIGNMENT: LINES __ 
STATIONS 
RESTRICTION TABLE 11 
TYPE: ALLOW ,/ 
DENY 
RESTRICTION TABLE 13 
TYPE: ALLOW i/ DENY - 
NTRY ENTRY NUMBER (16 MAXIMUM) 
112 13 14 15 16 17 16 19 1lOlll 12 13 14 15 16 
I I I I I ’ b 
I I I I I 
2 4 
I RESTRICTION TABLE 15 
I 
1 TYPE: ALLOW 
DENY - RESTRICTION TABLE 6 
TYPE: ALLOW DENY 
iNTRY ENTRY NUMBER (16 MAXIMUM) 
1 2 3 I3 14 15 16 
1 
I I I 
TABLE ASSIGNMENT: LINES - STATIONS 
RESTRICTION TABLE 10 
1 TYPE: ALLOW ~ DENY 
I 
TABLE ASSIGNMENT: LINES - STATIONS 
I RESTRICTION TABLE 12 
I 
1 TYPE: ALLOW - DENY 
I 
ENTRY ENTRY NUMBER (16 MAXIMUM) 
1 2 3 4 5 6 7 6 9 10 Ill 112 113 114 115 116 
1 
I I I I I I 
2 
1 i i i i i I 
3 
4 
TABLE ASSIGNMENT: LINES - STATIONS 
RESTRICTION TABLE 14 
TYPE: ALLOW DENY 
NTRYI ENTRY NUMBER 116 MAXIMUM) 
(10 (11 I12 113 114 115 116 
I I I I I I I I I I I I 1 I. i i i 
RESTRICTION TABLE 16 
TYPE: ALLOW 
DENY 
TABLE ASSIGNMENT: LINES - STATIONS 
I 
3-9b  
						

							\_ 
IMI 66-036 Programming 
LINE COS PROGRAMMING 
--------------^-------------------------------------------------- 
LINr: 
DEFAULTS 
0 Line type = TtiLCO 
0 Line groups = none assigned 
0 Dial Mode = Diilll? 
l Privacy status = private 
0 Toll Tables = none 
0 Abandoned Hold Timeout = 50 msec. 
assigned 
---------------^------------.------------------------------------- 
PKOCEDURX 
1 Rress ITCti 
* 7 4 6 * (base level entry if not now active) 
2 Select line to 
be pro
ammed. 
Pewrform all applicable steps. 
9 Press program 
key Al - Al4 
to choose line 1 - 14 3 
Select line type 
Press program 
key: 
0 Disabled = key C46 
0 Auxiliary = key C47 
l CO/PBX = key C4d 
4 Select line group 
Press program key: 
(multifunction confiy. only) 
0 None = key C41 
0 Gp 1 = 
key C34 
0 Gp 2 = Key C3S 
0 Gy 3 
= key C36 
l Gp 4 = key C37 
7 Assign toll tables 
Press program key(s) 
l Clear all assiynnents = C.33 
l Assign tables per chart 
6 Select privacy mode 
Press program key: 
0 Private = 
key C28 
0 idon-private = key C29 5 Select dialing mode 
Press program key: 
l Pulse/tone = key C26 
l Tone only = key C27 
6 Select privacy mode 
Press program 
key: 
0 Private = C28 
l Non-private = C29 
TAHLH 
KEY THBLH KtiY 
Cl0 3 Cl8 
Cl1 10 Cl9 
3 Cl2 11 c2lI 
4 Cl3 
i2 c21 
5 Cl4 13 Cl2 
8 Set abandoned hold timeout period 
Press 
program 
key: 9 Repeat steps 2 - 8 
l 300 msec. = key C42 for each line 
l 5d msec. = key C43 
10 Press * 
11 Press PlONIl?OK 
to exit or proceed to next COS programming step. 
3-l Oa  
						

							LINE COS PROGRAMMING REFERENCE TABLE 
l 
Shading denotes line default conditions. l Check off or enter the values chosen for the lines being programmed. 
BASE LEVEL @@mama 
LINE : PROGRAMMING MODE (Al-a 
I 
.IMI 66-036 Programming 
TOLL 
RESTRICTION 
TABLE 
ASSIGNMENT 
- 
I 12 I I 
- 
I 13 
CO/PBX NUMBERS 
AND STATION 
ASSIGNMENTS 
* Power Fail Lines (1, 2, and 3) 
** A-Lead Control Lines (7 and 8) 
3-lob  
						

							IMI 66-036 
Programming 
STATION COS PROGRAMMING 
-_----_----__--___--____________________------------------------- 
STATION DEFAULTS 
l PA port 
= disabled l Executive override = disabled 
0 Ringing line preference 
0 Prime line/group = none 
=disabled 
l Personal ringing tone = 0 Single Line Keyset accesses intercom  
tone 1 l Ringing assignment = all lines ring 
0 Toll tables = none assigned 
on stations 10, 17, 39, and 41 
0 Line access denied = none 
0 Origination denied = none 
0 Idle line preference = none 
0 All-call receive = enabled 0 Night transfer = all lines ring on 
stations 10, 17, 39 and 41 
0 All-call originate = enabled 
@ Reserved intercom Iink = none 
0 Zone page receive = disabled 
0 Message originate = disabled 
0 Zone page originate = 
disabled 0 Line/key assignment: 
l Automatic hold = disabled 
3 and 8 Line Keyset 
0 System speed dial toll restric.e BgFTad--keys(Bl=B8) = lines 1 - 8 
= disabled 
22 Line/Feature Keyset 
l Voice announce block = disabled@ A~ieldkeys-=-iines-i-- 14 
0 Privacy 
status = private 
0 B-Field keys = autodial locations 
----------------------------------------------------------------- 
PROCEDURE 
@ Perform all steps in sequence. 
l Skip those steps not required. 
1 Press ITCM * 7 4 6 * 
L 2 
(base level entry) 
3 Specify station to be programmed 4 
and perform applicable steps 
0 Press program key Cl0 - C41 
to select station port 10 - 41 
Action defaults following settings: 
0 PA port 
0 Prime line 
5 
l Voice blocking 
0 Executive override 
l Message wait-originate 
0 Automatic hold 
0 System speed dial toll rest, 
7 
0 Ringing line preference 
6 Enable 
executive override 
0 Press keypad key 3 Press program key B8 
(program entry) 
Enable PA port 
(DO NOT PROCEED BEYOND 
THIS STEP - 
IF PERFORMED) 
0 Press keypad key 1 
0 Return to step 3 
Block voice announced  
intercom calls 
0 Press keypad 
key 2 ’ 
Enable toll table restriction 
on system speed dial numbers 
l Press keypad key 4 
- continued 
Change Page 12i87 3-11  
						

							IMI 66-036 Programming 
Station COS - continued 
8 Choose personal ringing tones 
(22 Line/Feature Keysets) 
l TOAE 1 = keypad key 7 
. TONE: 2 = keypad 
key 8 
0 TONE 3 = keypad key 9 
. ‘I’(jNfi 4 = 
keypad key 0 
1Q Enable message wait 
originate 
0 Press keypad 
key 6 
12 Set ringing line preference 
0 Press program 
key: 
Enabled = BS 
Disabled = i34 
14 Select Night Transfer (ringing) 
0 Press program 
key C44 
(clears previous settings) 
0 Press program 
key(s) 
Al - Al4 = lines 1 - 14 
9 Set automatic hold 
l Press keypad key 5 
11 Select prime line 
or prime group 
0 Press program 
key Al - Al4 
to select line 1 - 14 
or press ITCM to select 
intercom line 
0 Press HOLD or 
key(s) Bl - 83 
to choose prime group 1 - 4 
13 Select ringing assignments 
RINGING 
0 Press program 
key C42 
(clears previous settings) 
0 Press program 
key(s) 
Al 
- Al4 = lines 1 - 14 
DELAYED HIWtiING 
0 Press program 
key C43 
(clears previous settings) 
0 Press program 
key(s) 
Al - Al4 = lines 1 - 14 
15 Select automatic privacy release 16 
l Press program key C45 
(clears previous settings) 
0 Press program 
key(s) 
Al 
- Al4 = lines 1 - 14 
97 Select call origination denied 18 
ti Press program 
key C47 
(clears previous settings) 
0 Press program 
key(s) 
Al - A14 
= lines 1 - 14 
3-12 Select access denied 
0 Press program 
key Cd6 
(clears previous settings) 
0 Press program key(s) 
Al - Al4 = lines 1 - 14 
Select idle line preference 
(hybrid config. only) 
0 Press program 
key C48 
(clears provious settings) 
0 Press program key(s) 
Al - Al4 = lines 1 - 14 
-continued  
						

							&I 66-036 Programming 
Station COS - continued 
19a Enter toll table assignment mode 
To clear all toll 
tables assigned 19b Specify toll tables l Press program keys 
l Press program key C49 per chart: 
/ KEY Al A2 A3 A4 A5 A6 A7 A8 
TABLE 1 2 3 4 5 6 7 8 
KEY A9 A10 All A12 A13 A14 B4 B5 
IABLB 9 10 11 12 13 
14 15 16., 
26 Reserve intercom link 
0 Press # 
0 Press keypad 
key 1-7 
to reserve link 1-7 
-or- 
@ Press 0 key for no reserved link 
0 Press console key C42 to 
Continue With next step 
Select all-call and/or zone paging 
0 Press 9 
0 Press RECALL to disable all paging assignments (if desired) 
ALL-CALL 
l Press program key A4 to originate 
0 Press program key A8 to receive 
0 Press console 
key C42 to continue with next program step 
ZONES A, B, AND C 
l Press # 
l Press program keys Al-A3 and 
AS-A7 to enable zones 
l Press console key C42 to continue with next program step 
- continued 
3-13