Home > Comdial > Communications System > Comdial Dxp Plus Instructions Manual

Comdial Dxp Plus Instructions Manual

Here you can view all the pages of manual Comdial Dxp Plus Instructions Manual. The Comdial manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 1121

Pulse characteristics such as repetition rate, pulse width, pulse amplitude, and average ones density ((ratio
of one (1) bits to zero (0) bits)) are as specified by digital signal level 1 (DS-1) described in American
National Standards Institute Specification, ANSI T1.403-1989.
Detailing Where You Can Install T1/PRI Boards and Its Supporting Needs
Since the DXPPlussupports a maximum of 240 lines, and each T1/PRI board handles up to 24 channels,
you can install up to 10 boards in the DXPPlussystem. You...

Page 1122

SMDA Metering Pulse Totals
DXPPlussoftware 11A enhances the SMDA Metering Pulse Totals by adding a third option to the
Report Option field. You can now select the option “Meter Pulses” as an alternative to “Call Cost” or
“Hold Time” on all reports.
Metering Pulse is a method used in countries other than the United States to determine call duration and
cost. Therefore, if you are installing the DXPPlussystem in a country that uses E1 lines, selecting this
option will allow the DXPPlusto cost calls by...

Page 1123

TECHNICAL ADVISORY BULLETIN
Date: April, 1997 Issue: TAB004–PLS
Software Enhancements For The
DXPPlusDigital Communications System
This bulletin discusses the following software enhancements and feature additions to the DXP plus digital
communications system that are available with software release 11B and later.
·ANI/DNIS Display
·PCIU/Visual Call Manager Support
·Phone Types Enhancement
·Restricted Login
·System Software Upgrade Enhancement
·Visual Voice Mail Support
NOTE: It is always a good practice...

Page 1124

ANI/DNIS Display
Software 11B adds the ANI/DNIS display feature. Automatic Number Identification (ANI) describes a
code delivered by the subscriber service along with an incoming call. ANI identifies the number that the
caller calls from. Dialed Number Identification Service (DNIS) also describes a code delivered by the
subscriber service; however, DNIS identifies the number that the caller dialed.  Systems can make use of
these two services in different ways. One use is to show the ANI or DNIS...

Page 1125

PCIU/Visual Call Manager Support
Beginning with software release 11B you can use the Personal Computer Interface Unit (PCIU) to operate
the Visual Call Manager (VCM) capability of the Versatile Voice Processing (V.V.P.) voice mail system.
VCM provides a series of computer-displayed menus that V.V.P. users can use to simultaneously view
and manage voice message activity. By using a series of PC screen menus, users click their computer
mouse to send, forward, save, delete, and listen to voice mail messages...

Page 1126

Phone Types Enhancement
(Telephone Types)
This programming feature allows you to identify the particular type of system telephone equipment that
you or your installer will connect to each station port.
Beginning with software 11B, the digital communications system supports the installation of an
integrated voice processing board as a digital station type selection. The model number of the Comdial
integrated voice processing board is as follows: IVPC
You can also mark the station port equipment as...

Page 1127

Restricted Login
Software release 11B, provides upward and backward compatibility between the different revisions of the
VMMI programming software and the software of the system being programmed. This compatibility is
for certain critical features and is known as restricted login. For example, restricted login permits
programmers to use 11A VMMI software to execute certain programming features on an 11B system or
use 11B VMMI software on 10A systems.  Restricted login permits the programming of the...

Page 1128

System Software Upgrade Enhancement
Beginning with software release 11B, digital communications system installers no longer need to accept
an automatic save of an existing database during a system software upgrade. Installers can choose to
maintain the existing data base by first archiving the data base, then upgrade the software, and finally
restore the database after the upgrade is complete. Alternately, installers can choose to allow the system
to clear the existing database with the master clear...

Page 1129

Visual Voice Mail Support
Visual Voice Mail (VVM) support provides proprietary, two-line display LCD speakerphone stations
with visual messages and interactive buttons. This message and button functionality enhances the stations
with visual messages and interactive buttons. This message and button functionality enhances the
station’s use with Comdial Versatile Voice Processing (V.V.P.) voice mail equipment.
The V.V.P. prompts the user to enter a password (if programmed to require one) before it plays the...

Page 1130

Upgrading The DXP Plus Software
The DXPPlusdigital communications system includes system software when it ships from the factory.
At initial system installation, you do not need to load the system software to make the system operational.
Should you need to later reload the system software (for software up-grade purposes for example), you
can do so using the supplied system software disk. Use Windows File Manager or MS–DOS commands
to save the disk’s information from your computer’s floppy drive to its...
Start reading Comdial Dxp Plus Instructions Manual

Related Manuals for Comdial Dxp Plus Instructions Manual

All Comdial manuals