Comdial Digital Telephone System Instructions Manual

System OperationControls And IndicatorsIM166-107
Ringer Volume Control
Each station has a ringer volume control.Adjust the
ringer volume of each station as desired by its user.
TelephoneControl Location
7114s, 7114sRocker switch located on
6012S, 60248front faceplate.
8012S, 8112sAdjust while ringing
to set volume.
7701x, 8101NSwitch on bottom housing.8112N
Set for fixed volume levels.
701 OS, 711 oxSwitch on left side of telephone.
7016sSet for fixed volume levels.
Status Indicators And Tone Sequences...

SYSTt..r RINGING PATTERNS
tI.
COlPBX Line Ring
Intercom Tone 
SignaltinsVoice 
Stgnalling alert
Timed hold recall at
station that put call
on hold
:all back alert
Iueue Enableds
‘all forward alert
‘ansfer ringingHost system ring cadence
Two 150 msec. tone bursts
sounded every 4 seconds
One 215 
msec. tone burst
Three 150 msec. tone bursts
sounded at the end of each
timeout period
3ne 80 msec. tone burst
lollowed by three 150 msec.
!one bursts and one 80 msec.
:one burst
3ne 80 msec. tone burst
Two 1 
.l...

INTERCOM CALL PROGRESS TONES
(Heard through handset receiver or over monitor speaker)
sounded three times
otification tone
followed by 280 msec.
lverride feature
ut allowed
Nignt transfer feature
not allowed530 msec. tone bursts
sounded continuously 

c
J
Call waiting tone
Three 80 msec. tone bursts
soundedonce
Called station in 
do-not-140 msectone burst
disturb mode
sounded twice every
1.5 sec.
Call-back busy feature on260 msec. tone burst
soundedonce
I
System is awaiting
80 msec. tone bursts sounded
memory dial number
continuously
or key mapping entry
lln_
after location is specified
Override feature on
- warning tone
Six 100 msec tone bursts
sounded for 1.5 sec.
iOHVA tone
NSD ringback toneDual 440/460 Hz tone
sounded 1 
sec.on/l set off.trc
d-4,...

LINE SELECT LIGHTS
idleSteady off
RingingContinuous flash
(560 msec. on - 560 msec. off)III
In useYour stationGreen indicator - on steady
Other stationRed indicator - on steady
On holdYour stationGreen indicator - continuous winking(490 msec. on - 70 msec. off)
uuuuuOther stationRed indicator - continuous winking
(490 msec. on - 70 msec. off)
Exclusive holdRed indicator 
- steady on
at other station
Held callYour stationGreen indicator 
- continuous flutter
time out
(70 msec. on - 70 msec. off)
Other...

MESSAGE WAITING LIGHT
Message WaitingContinuous flash
(560 msec. on 
- 560 msec. off)II
INTERCOM LIGHT
In use 
- your station
Auto 
redial activeSteady on with wink off
(2.3 sec. on 
- 70 msec. off)
Continuous flash
(70 msec. on 
- 70 msec. off)
Messaging display
Night mode
-Station 10 and 12Continuous winking
(490 msec. on 
- 70 msec. off)
Flutter with repeative off periods
(flutter rate 
- 560 msec. off)
uuIIuuu
n
cAJso23 

BLF LIGHTS
LCD messagingContinuous flash
(70 msec. on - 70 msec. off)DSS station idleSteady off
DSS station bus
Yon outside
line or intercom ine.
DSS station in do not
disturb mode.
SPEAKER LIGHTSteady on
Steady on
MUTE LIGHT
vSteady on 

IMl66-107
Maintenance
Chapter 6
Maintenance
:
Technical AssistanceTechnical Assistance
Should you experience difficulty with installation,
checkout, or programming, and have made an attempt
to isolate the problem using information provided
herein; or should you encounter problems at a later
date which cannot be resolved by referring to this
manual, call the 
Comdial Technical Service staff.
They can be reached at 
1-800-388-8224 between the
hours of 8:00 AM and 8:00 PM Eastern time, Monday
through...

MaintenanceIMl66-107Frequently Asked Questions Concerning The Digital Telephone System
QuestionAnswerSystem Manual Reference
What prevents the speaker light
from turning off?Check to see if background music is
turned on. Verify if the station port is
programmed in the headset modePages 2-3,2-l 3, 2-18, 4-29
Why is the display on the LCD
speakerphone difficult to read?Adjust the LCD contrast level by holding
the MUTE button down for more than
five seconds and let contrast levels 0 -7
scroll through until...

IMl66-107
Maintenance
Question
Speed dial locations are
programmed but sometimes will
not dial when the users use them.
What causes this to happen?Answer
This is could happen when the speed
dial is programmed to only access a
specific line. If this line is busy, no
action will ensue. When programming
speed dial numbers, select a line group
instead of an individual line.
System Manual Reference
Pages.2-2,2-16,2-18,
2-22, 
3-1,4-10,4-17
What could prevent a line light
from turning on when auxiliary...