Cisco Wap4410n Wirelessn Manual

Configuring the Cisco WAP4410N Wireless-N Access Point
Wirele ss
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 41
6
Advanced Settings
The Wireless > Advanced Settings page allows you to configure the advanced 
wireless and load balancing settings for the access point. The access point uses 
several parameters to adjust the channel bandwidth and guard intervals to 
improve the data rate. We recommend you let your access point automatically 
adjust the parameters for...

Configuring the Cisco WAP4410N Wireless-N Access Point
Wirele ss
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 42
6
WAP4410N sends multicast and broadcast messages every 1 beacon 
interval, if the Beacon Interval field is set with the default of 100ms.
Lower settings result in more efficient networking, while preventing your 
computer from dropping into power-saving sleep mode. Higher settings 
allow your computer to enter the sleep mode, thus saving power, but...

Configuring the Cisco WAP4410N Wireless-N Access Point
AP Mode
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 43
6
AP Mode
The AP Mode page displays the AP mode settings for the access point. To 
configure the AP mode of the access point, follow these steps:
STEP 1Click AP Mode > AP Mode.
STEP  2Configure the AP Mode settings.
•Access point—Select to let the device operate as a normal access point.
-Allow Wireless Signal to be repeated by a repeater—If selected, the...

Configuring the Cisco WAP4410N Wireless-N Access Point
Administration
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 44
6
-Not in Legal AP List—Check to flag any access point not listed in the 
Legal AP List as a rouge access point. If you check this check box, you 
must maintain the Legal AP List.
-Define Legal AP—Click to open a sub-screen where you can modify the 
Legal AP List. This list must contain all known access points. You must 
maintain this list.
STEP  3Click...

Configuring the Cisco WAP4410N Wireless-N Access Point
Administration
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 45
6
-Web HT TPS Access—Enable HTTPS if needed. The default is 
Disabled. 
-Wireless Web Access—Allow or deny wireless clients to access web-
based utility. The default is Disabled.
•Remote Console—Enable Secure Shell (SSH) to exchange data over a 
secure channel between two computers.
-Secure Shell (SSH)—Enable SSH if needed. The default is Disabled....

Configuring the Cisco WAP4410N Wireless-N Access Point
Administration
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 46
6
Log
The Administration > Log page allows you to have logs that keep track of the 
access point’s activities.
STEP 1Click Administration > Log.
STEP  2Configure the log settings.
•Email Alert
-E-Mail Alert—If you want the access point to send e-mail alerts in the 
event of certain attacks, click Enabled. The default is Disabled.
-SMTP Server—Enter the...

Configuring the Cisco WAP4410N Wireless-N Access Point
Administration
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 47
6
STEP  3Click Save.
Diagnostics
The Administration > Diagnostics page allows you to use the access point to 
perform a ping. The activity can be useful in solving network problems. To perform 
a ping test to help diagnose problems with the access point, follow these steps:
STEP 1Click Administration > Diagnostics.
STEP  2Set up the ping test:
•IP or URL...

Configuring the Cisco WAP4410N Wireless-N Access Point
Administration
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 48
6
Factor y Default
The Administration > Factory Default page allows you to restore the access 
point’s factory default settings. Note any custom settings before you restore the 
factory defaults. Once the access point is reset, you will have to re-enter all of your 
configuration settings.
STEP 1Click Administration > Factory Default.
STEP  2Click Ye s to...

Configuring the Cisco WAP4410N Wireless-N Access Point
Administration
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 49
6
d. In the File field, enter the location of the firmware upgrade file or click the 
Browse button to locate the file.
e.
Click Upgrade and follow the on-screen instructions.
STEP  3Re-enter all of your custom configuration settings.
Reboot
The Administration > Reboot page allows you to reboot the access point. To 
reboot the access point, follow these...

Configuring the Cisco WAP4410N Wireless-N Access Point
Status
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 50
6
SSL Certification Management
To generate the certificate with the WAP device, click Export Certificate. 
Generating a new SSL certificate restarts the secure Web server. The secure 
connection will not work until the new certificate is accepted on the browser.
If an SSL certificate (with a .pem extension) exists on the WAP device, you can 
install it to your...