Cisco Wap4410n Wirelessn Manual

Configuring the Cisco WAP4410N Wireless-N Access Point
Status
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 51
6
-Primary DNS—The IP address of your primary DNS server. 
-Secondary DNS—The IP address of your secondary DNS server. 
STEP  2To update the status information, click Refresh. 
Wireless
The Status > Wireless page displays the access point’s current status information 
for the wireless network. To check wireless network status of the access point, 
follow these...

Configuring the Cisco WAP4410N Wireless-N Access Point
Status
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 52
6
System Performance
The Status > System Performance page displays the access point’s status 
information for its current settings and data transmissions. To check system 
performance of the access point, follow these steps:
STEP 1Click Status > System Performance.
This page displays the access point’s system performance values:
•Wired—The statistics for the...

Configuring the Cisco WAP4410N Wireless-N Access Point
Status
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 53
6
-Bytes Sent—The number of bytes sent for each wireless network.
-Error Packets Received—The number of error packets received for 
each wireless network.
-Drop Received Packets—The number of packets being dropped after 
they were received.
STEP  2To update the system performance status information, click Refresh.  

A
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 54
Troubleshooting
This appendix provides solutions to problems that might occur during the 
installation and operation of the Cisco WAP4410N Access Point. 
Read the descriptions below to help solve your problems. If you cant find an 
answer here, check the Cisco.com website at 
www.cisco.com/en/US/support/
tsd_cisco_small_business_support_center_contacts.html
.
Frequently Asked Questions
Q. Can the access point act as my...

Troubleshooting
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 55
A
Q. What is the IEEE 802.11b standard?
It is one of the IEEE standards for wireless networks. The 802.11b standard 
allows wireless networking hardware from different manufacturers to 
communicate, provided that the hardware complies with the 802.11b 
standard. The 802.11b standard states a maximum data transfer rate of 
11Mbps and an operating frequency of 2.4 GHz.
Q. What is the IEEE 802.11g standard?
It...

Troubleshooting
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 56
A
The Cisco WAP4410N Access Point supports the following IPv6 
Applications:
-WEB/SSL
-SNTP
-PING6
-TRACE Route 
Q. What is roaming?
Roaming is the ability of a portable computer user to communicate 
continuously while moving freely throughout an area greater than that 
covered by a single access point. Before using the roaming function, the 
workstation must make sure that it is set to the same channel...

Troubleshooting
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 57
A
Q. What is the ISM band?
The FCC and their counterparts outside of the U.S. have set aside 
bandwidth for unlicensed use in the ISM (Industrial, Scientific and Medical) 
band. 
Spectrum in the vicinity of 2.4 GHz, in particular, is being made available 
worldwide. This presents a truly revolutionary opportunity to place 
convenient high speed wireless capabilities in the hands of users around 
the globe....

Troubleshooting
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 58
A
Q. Would the information be intercepted while transmitting on air?
WLAN features two-fold protection in security. On the hardware side, as 
with Direct Sequence Spread Spectrum technology, it has the inherent 
security feature of scrambling. On the software side, the WLAN series 
offers a variety of wireless security methods to enhance security and 
access control. Users can set it up depending upon their...

Troubleshooting
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 59
A
Q. Does the access point function as a firewall?
No. The access point is only a bridge from wired Ethernet to wireless 
clients. 
Q. I have excellent signal strength, but I cannot see my network. 
Wireless security, such as WEP or WPA, is probably enabled on the access 
point, but not on your wireless adapter (or vice versa). Verify that the same 
wireless security settings are being used on all devices in...

Troubleshooting
WAP4410N Wireless-N Access Point with Power Over Internet Administration Guide 60
A
TCP/IP
Before a computer can communicate with the access point, TCP/IP must be 
enabled. TCP/IP is a set of instructions, or protocol, all computers follow to 
communicate over a network. This is true for wireless networks as well. Your 
computers will not be able to utilize wireless networking without having TCP/IP 
enabled. Windows Help provides complete instructions on enabling TCP/IP.
Shared Resources...