Cisco 6500e Manual

1-29
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Installing a Catalyst 6509-NEB or Catalyst 6509-NEB-A Switch Chassis
Rack-Mounting the Chassis
This section provides procedures for installing either the Catalyst 6509-NEB or the 
Catalyst 6509-NEB-A switch chassis in a 19-inch rack enclosure.
NoteThe chassis are designed to be mounted in equipment racks that meet ANSI/EIA 310-D and 
ETS 300-119 standards.
WarningTwo people are required to lift the...

1-30
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Installing a Catalyst 6509-NEB or Catalyst 6509-NEB-A Switch Chassis
Figure 1-13 Installing a Catalyst 6509-NEB or a Catalyst 6509-NEB-A Switch Chassis in a Rack
112-24 or 10-32 rack-mounting screws (10x)2Shelf bracket
INPUT
OKFA N
OKOUTPUT
FA IL
o
280388
POWER SUPPLY 1
POWER SUPPLY 2
W
S
-S
U
P32
-G
E
-3
BSTA
TUS
SYSTEM
ACTIVE
PWR
 MG
MT
RES
ETC
A
TA
L
Y
S
T
   6
500
 S
UP
E
R
V
ISO
R
  
E
N
G
IN
E...

1-31
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Installing a Catalyst 6509-NEB or Catalyst 6509-NEB-A Switch Chassis
Installing the Cable Management System (Catalyst 6509-NEB-A Only)
This section describes the installation procedures for the cable management system (CABLETRAY-09) 
on the Catalyst 6509-NEB-A switch. 
NoteThe cable management system is shipped with the extended cable guide installed but can be used with 
the supplied standard cable...

1-32
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Installing a Catalyst 6509-NEB or Catalyst 6509-NEB-A Switch Chassis
Step 3Loosen the two captive installation screws on the front panel. (See Figure 1-15.)
Figure 1-15 Removing the Front Panel 
Step 4
Remove the front panel, and set it aside.
Step 5Attach the interface cables to the modules, and route the cables through the cable guide. 
Step 6Install the front panel by positioning the top of the...

1-33
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Installing a Catalyst 6509-NEB or Catalyst 6509-NEB-A Switch Chassis
Replacing the Cable Guide
To replace the cable guides on the cable management system, perform these steps:
Step 1Loosen the two captive installation screws on the front panel. (See Figure 1-16.)
Figure 1-16 Removing the Front Panel 
Step 2
Remove the front panel, and set it aside.
Step 3Remove the two screws that secure the cable...

1-34
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Installing a Catalyst 6509-NEB or Catalyst 6509-NEB-A Switch Chassis
Step 4Install the standard cable guide to the back panel by securing the lip of the cable guide to the back panel. 
(See Figure 1-17.) 
Step 5Install the two screws to secure the cable guide to the back plate. (See Figure 1-17.)
NoteBefore installing the front panel, attach the interface cables to the modules, and route the cables...

1-35
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Installing a Catalyst 6509-NEB or Catalyst 6509-NEB-A Switch Chassis
What is Next
After installing the chassis in its location, complete the installation process by performing these 
procedures:
Connecting the chassis to system ground. See “Establishing the System Ground” section on 
page 1-52.
Installing and connecting the power supplies to source power. Go to Chapter 4 for information on 
how to...

1-36
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Installing a Catalyst 6509-V-E Switch Chassis
Installing a Catalyst 6509-V-E Switch Chassis
This section provides procedures for installing a Catalyst 6509-V-E switch chassis in a rack assembly 
and installing the optional cable guide system. 
Installation Accessory Kit
The Catalyst 6509-V-E switch chassis is designed to be installed in a standard 19-inch rack, either open 
or enclosed. The chassis is...

1-37
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Installing a Catalyst 6509-V-E Switch Chassis
Figure 1-19 L Brackets on the Catalyst 6509-V-E Switch Chassis
Installing the 3 RU Rack-Mount Shelf
The 3 RU rack-mount shelf is included as part of the accessory kit for the Catalyst 6509-V-E switch 
chassis. You need to install this kit first before you install the chassis in the rack. The shelf kit supports 
the weight of the chassis while you install...

1-38
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Installing a Catalyst 6509-V-E Switch Chassis
Rack-Mounting the Chassis
TipWe recommend that you have a third person to assist in this procedure.
CautionFor easier installation, the chassis should be empty when you install it in the rack.
WarningTwo people are required to lift the chassis. To prevent injury, keep your back straight and lift with your 
legs, not your back. Statement 164
To install the...