Christie Projector Roadster, Matrix WU, Mirage S+/HD/WU User Manual

 Installation & Setup 
Roadster, Matrix WU, Mirage S+/HD/WU User Manual 2-21 020-100002-05 Rev. 1 (02-2010)  
Use the DVI-I connector at INPUT 2 to connect either analog or digital video devices 
to the projector. When connecting devices that transmit an analog video signal such 
as VCRs, laptops, and PCs use the DVI cable provided with the projector. Plug the   
DVI-I (single link) connector end to the projector and the 15-pin VGA connector to 
the device.  
Use a cable with DVI-I connectors at both...

Installation & Setup  
2-22 Roadster, Matrix WU, Mirage S+/HD/WU User Manual   020-100002-05 Rev. 1 (02-2010) 
NOTES: 1) Optional digital interfaces cannot be used in a Marquee Case/Power 
Supply. 2) Refer to Appendix D, Optional Input Modules for a brief description of 
each interface. 
As an alternative to the projector’s keypad or remote, you may wish to communicate 
with the projector using a PC or other controller. Such a device sends commands and 
receives feedback via serial links (RS-232 and...

 Installation & Setup 
Roadster, Matrix WU, Mirage S+/HD/WU User Manual 2-23 020-100002-05 Rev. 1 (02-2010) 
 
Figure 2.28. RS-422 Connection to a Computer 
 
 WARNING  
Do not use an RS-422 port unless you are using 
equipment with RS-422 capability. The voltage levels of 
this signal can damage incompatible equipment. 
Ethernet Communications 
To add the projector to an existing Ethernet network with other equipment such as 
controllers and other projectors, connect standard CAT5 Ethernet cable between...

Installation & Setup  
2-24 Roadster, Matrix WU, Mirage S+/HD/WU User Manual   020-100002-05 Rev. 1 (02-2010) 
NOTE: Ensure the projector is connected to the network before attempting to change 
its IP address. 
Regardless of how it is assigned, once a projector has a valid and unique address it 
will respond to commands sent to this address. To determine the projector’s current 
IP address, consult the Status or Communications menus. 
Refer to 3.7, Adjusting System Parameters and Advanced Controls for...

 Installation & Setup 
Roadster, Matrix WU, Mirage S+/HD/WU User Manual 2-25 020-100002-05 Rev. 1 (02-2010) 
 
Figure 2.31. RS-232 Serial Link Loop-Through at First Projector 
MIXED NETWORK: To control multiple projectors with a computer/controller having 
an RS-422 interface, first set them all to the same baud rate as your RS-422 
controller. 
 
NOTE: You must enable this combination of RS-422 and RS-232 in the 
Communications menu. Set the “Network Routing” option to “RS-232 and RS-422 
Joined”. Refer...

Installation & Setup  
2-26 Roadster, Matrix WU, Mirage S+/HD/WU User Manual   020-100002-05 Rev. 1 (02-2010) 
NOTES: 1) To avoid damage, connect only properly wired serial communication 
cables. Refer to Appendix B for details. 2) It is recommended that each RS-232 
communication cable be no more than 25 feet in length. Use high quality cables. 
ETHERNET NETWORK SETUP: To add one or more projectors to an Ethernet network, 
use standard CAT5 cable to connect each projector’s Ethernet port to a hub on to...

 Installation & Setup 
Roadster, Matrix WU, Mirage S+/HD/WU User Manual 2-27 020-100002-05 Rev. 1 (02-2010) 
CHANGING THE PORT#: On some Ethernet networks, firewall restrictions may 
require that the port number of the projector be changed from its default of 3002. If 
so, enter a new port number in the Ethernet Settings menu or include the new port# in 
an XIP serial command sent to the projector. It is highly recommended not to use a 
port# below 1024, as these ports are typically reserved for and used...

Installation & Setup  
2-28 Roadster, Matrix WU, Mirage S+/HD/WU User Manual   020-100002-05 Rev. 1 (02-2010) 
 
Figure 2.36. Joining All Networks 
To isolate just RS-422 communications, select “RS-232 and Ethernet Joined”. In 
Figure 2.36, only projector #3 will respond to the RS-422 controller. To isolate just 
Ethernet communications, select “RS-232 and RS-422 Joined”—only projector #1 
will respond via Ethernet.  
 
 The North American rated line cord is provided with each projector. Ensure 
that you...

 Installation & Setup 
Roadster, Matrix WU, Mirage S+/HD/WU User Manual 2-29 020-100002-05 Rev. 1 (02-2010) 
The projector is set up at the 
factory for use in a front 
screen, floor mount 
orientation. If your initial 
installation is ceiling mount 
or rear screen, displayed 
images may be upside down 
and/or reversed. To correct, 
you must change the image 
orientation from within the 
Configuration Menu (you 
may prefer to do this before 
physically installing the 
projector in its final...

Installation & Setup  
2-30 Roadster, Matrix WU, Mirage S+/HD/WU User Manual   020-100002-05 Rev. 1 (02-2010)   
With the input image displayed: 
 If remote keypad: Press Zoom 
 or .
 
 If built-in keypad: Press Zoom 
 or .
 
Hold the key down to see the effect –arrows in the display 
indicate the direction of the zoom (Figure 2.39). 
 
 
With the input image displayed: 
 If remote keypad: Press Focus 
 or .
 
 If built-in keypad: Press Focus
 
 or .
 
Hold the key down to see the effect – arrows in...