Christie Projector Roadie 4K35 User Manual

							d) Reinstall and secure the LPS side panel with six screws.
Notice. Failure to comply with the following may result in property damage.

						

							Danger! F
ailure to comply with the following results in death or serious injury .

						

							4. Tighten the screw to secure the harness in place.
Ensure the wire insulation is not crimped under the screw .
5. Slide the selector switch to the  200V location. 6. Re-attach the front panel.
Configuring
 ballast settings for 400 VAC operation
Convert the voltage to 400 VAC for the lamp power supply (LPS). 1. Unplug the LPS from power.
2. Remove the front panel using a Philips screwdriver.
3. Insert the convenience outlet harness (black) wire into the second position on the terminalblock. Installation and Setup
Roadie 4K35 User Manual
23
020-101669-04 R
 ev. 1 (01-2016)
Copyright  
						

							4. Tighten the screw to secure the harness in place.
Ensure the wire insulation is not crimped under the screw .
5. Slide the selector switch to the 400V location. Installation and Setup
Roadie 4K35 User Manual
24
020-101669-04 R
 ev. 1 (01-2016)
Copyright  
						

							6. Re-attach the front panel.
Adjusting the pr ojector tilt and level
Adjust the projector tilt to fill the maximum amount of screen while minimizing k eystone. Lens offset
can be used to center the image in the center of the screen. Warning! 
F
 ailure to comply with the following could result in death or serious injury .

						

							4. Once the required adjustment is made, tighten the lock nut against the bottom of the
projector (B).
The projector pro
vides 27 mm of adjustment at the front and at the rear.
5. If the vertical or horizontal position of the projector requires more adjustment than the standard feet allow, two 6-inch extension rods can be installed to increase the amount of
available adjustment.
Installing the foot extension rods Increase the height of the projector with foot extension rods. 1. Elevate the rear of the projector to access the two rear feet.
2. Remove the feet by loosening the lock nut and rotating the each foot out of the projector.
3. Add the extension rods to the standard feet.
4. Thread the extended feet into the projector
						

							4. Fasten the end of the touch panel controller safety strap attached to the ball joint on the
projector to the touch panel controller ball joint using the M4 screw remo ved in the previous
step.
The touch panel controller safety strap comes installed on the projector ball point.
5. Connect the cable from the touch panel controller to the connector on the rear panel of the projector.
6. Adjust the touch panel controller angle for optimal viewing, then tighten the mounting arm lock securely so that the touch panel controller is held in place at the required location. Connecting external exhaust ducting (optional)
Connect exhaust ducting to the low profile extr
 actor located on top of the rear of the projector to
extract hot air from the lamp compartment and exhaust it out of the rear of the projector.
External exhaust ducting can be connected to remove hot air from the projector by installing the
optional Ducted Exhaust Kit (P/N: 113-107109-XX).
Related information
Accessories (on page 80)
Removing the projector shroud (optional) The lens side shroud must be removed to gain access to the lens. The other shroud must be removed
when connecting the AC power cord into the front face of the projector .Warning! 
F
 ailure to comply with the following could result in death or serious injury .

						

							3. Place the shroud covers on a clean surface to prevent scratches.
Setting up the lens Only use lenses designed for 
Roadie 4K35 projectors. Warning! 
F
 ailure to comply with the following could result in death or serious injury .

						

							8.
Calibratethelensmotors   (on page 63).
Related information
Workingwithlenses  (on page 46)
Removingtheprojectorshroud(optional)  (on page 27)
Orienting the projector in portrait mode Change the orientation of the projector to portrait. 1. Install the projector in the Roadie 4K frame (P/N: 129-115108-XX) according to theinstallation instructions provided with the frame.
2. Orient the projector in the frame with the lamp door facing downward (as shown). The maximum tilt angle is 
						

							Connecting devices
Learn the information and procedures for connecting external devices to the projector .
Communication and input ports are located on the projector side input panel. When connecting
devices, you can route cables through the opening in the frame to the side input panel or directly to
the video option cards and MCPU. The image below shows the video option card slot numbers and the
MCPU panel.
Input signal devices are connected to the video option cards and the option card slot numbers are
important for some types of input signals. Communication devices are connected at the MCPU panel. SLOT 1
SLOT 2
SLOT 4
SLOT 3 MCPU
Input video mapping
Video input mapping depends on the t
 ype of cards used for the Four-Port or Two-Port input
configurations.
Four-Port: 3GIC, TDPIC, THIC cards View the video quadrant mappings for the 3GIC, TDPIC, and THIC Four-Port input configurations.
Four-Port input configuration