Christie Projector Mirage M Series User Manual

							Section 7: Specifications
Mirage M Series User Manual7-3020-100575-02  Rev. 1  (11-2010)
7.1.10 Convergence
Convergence zones A, B, C are as defined in Figure 2. Zone A has a diameter ¼ of the image height. Zone B has a diameter 
of full image height. All specified convergence errors are between any two colors after a minimum warm-up of 30 minutes. 
Convergence is specified with a 1.4-1.8 HD lens (part number 118-100112-01) in the 1.4:1 position with zero offset. Bore-
sight alignment must be adjusted for zero angular error. (Note: convergence error includes the effects of lateral color in the 
projection lens. Measurements must be done on horizontal and vertical test pattern lines that intersect the center of the 
image).
7.1.11 Blemishes
Blemishes are to be observed at 1 full screen height distance from the image for a period of 30 seconds. Screen size: 10 foot 
wide for 350W models, 8 foot wide for 200W models. Blemishes are defined as per TI Specification 2506811.
7.1.12 Pixel Defects
7.1.13 Image Artifacts
Measurement
 AreaMaximum Convergence 
Error (Pixels)
Zone A 1/4 
Zone B 1/2 
Zone C 3/4 
Red screen No blemishes
Green screen No blemishes
Blue screen No blemishes
White screen No blemishes
Black screen No blemishes
Red  0 bright, 1 dark
Green 0 bright, 0 dark
Blue  0 bright, 2 dark non-adjacent
Evaluate on multi-burst or fine grid test pattern  No visible artifacts with observer at 1 full screen 
height from image 
(Figure applicable to both 1080p and SXGA+) 
						

							7-4Mirage M Series User Manual020-100575-02  Rev. 1   (11-2010)
Section 7: Specifications
7.1.14 Picture Centering (with 1.4-1.8:1 HD lens)
7.2 Feature Set
7.2.1 Airflow 
7.2.2 Air Filters (Optional)
7.2.3 Dust Sealing
7.2.4 ILS (Intelligent Lens System)
7.2.5 Projection Lens Compatibility
HD (1920x1080p) centering error ±5% of vertical offset (±32 pixels)
SXGA+ centering error ±5% of vertical offset (±26 pixels)
WUXGA centering error ±5.5% of vertical offset (±32 pixels)
Air intakes                Right side of projector
Air exhaust  Hot lamp exhaust: rear of projector
Cool light engine exhaust: left side of projector
Filter media types           Coarse foam filter
Fog filter
Filter access Service-interchangeable via access panel
Dust sealed DMDs                Gasket sealed
Dust sealed illumination system  Sealed from lamp input to entrance face of prism when 
lamps are installed
Motorized lenses and lens mount with position 
encoding              Zoom, focus, horizontal and vertical offsets
Accuracy ±2 pixel
Manual control 1/3 pixel fine movement control per button press on 
any applicable User Interface (e.g., remote).
Calibration 
User Configurable Calibration ModesAutomatic calibration on lens change detection
Automatic calibration on power-up
Manual calibration
Calibration time < 10 secs when required
Bore sight 3-point +- 4 degrees adjustment and lockable without 
removing covers
Travel time stop to stop
Zoom and Focus 10 sec nominal (depends on lens type)
Offsets 5 sec (nominal (depends on lens type)
Manual Lens Movement Manual over-ride permissible for zoom and focus
Lens type Reverse Telecentric Internal-focus
Motorized zoom and focus with position feedback
NOTE: Calculated Throw distance values are subject to a ±5% lens tolerance  
						

							Section 7: Specifications
Mirage M Series User Manual7-5020-100575-02  Rev. 1  (11-2010)
Lens Throw Ratio
7.2.6 Iris 
7.2.7 Automatic Fans
7.2.8 Constant Lamp Output Management
7.2.9 Shutter 
Lens DescriptionPart NumberWUXGA Throw Ratio
FixedLens ILS 0.73:1SX+/0.67:1HD118-100110-xx 0.67
Lens ILS 1.2SX+/1.1HD 118-100117-xx 1.1
ZoomLens ILS 1.25-1.6SX+/1.16-1.49HD
118-100111-xx 1.16-1.49
Lens ILS 1.5-2.0SX+/1.4-1.8HD118-100112-xx 1.4-1.8
Lens ILS 2.0-2.8SX+/1.8-2.6HD118-100113-xx 1.8-2.6
Lens ILS 2.8-4.5SX+/2.6-4.1HD118-100114-xx 2.6-4.1
Lens ILS 4.5-7.5SX+/4.1-6.9HD 118-100115-xx 4.1-6.9
Lens ILS 7.5-11.2SX+/6.9-10.4HD118-100116-xx 6.9-10.4
Motorized iris with position feedback               Scene controlled motorized iris automatically 
adjusts to image content
Max frequency open-close-open 20 Hz
Sound level Within ambient noise level of projector
Configurable per channel
Temperature sensitive fan speed control Fans automatically adjust to required speed to 
maintain projector at proper operating range as 
function of outside ambient temperature
Standby All fans are off when projector is in standby and not 
running active loop-through on a Twin HDMI 
option card
Temperature range for variable fan speed  5 to 40 degrees C
Transition steps Smooth speed transitions with no abrupt audible 
changes
LiteLOC
              Automatically adjusts lamp output to maintain 
constant lumens setting within operating range of 
lamp.
Open Light transmitted to projection lens
Closed All light blocked - no light on screen
Activation Operation in less than 0.25 seconds.  
						

							7-6Mirage M Series User Manual020-100575-02  Rev. 1   (11-2010)
Section 7: Specifications
7.2.10 Lamps
7.2.11 Status LED
7.2.12 Electronics/SW 
Dual Mercury lamp system               Lamps are accessed from side of projector
Lamps are individually swappable while the 
projector is running 
Status LED’s               Located at back of projector
LED STATES
Lamp 1, Lamp 2Off – Lamps are off
Yellow – Lamp time has expired and lamp should be replaced
Green – Lamp is on and operating correctly
Flashing red – Lamp has malfunctioned
PowerOff – AC power is off
Yellow – AC is present but projector is in standby
Green – Projector is powered up and operating normally
Flashing green/yellow – Projector communication in progress
Flashing red – Error has occurred. Details are displayed on the status display
ShutterGreen – shutter is open
Yellow – shutter is closed
FEATURE COMMENTS
Video Format Re-Sizing All video formats can be resized to fill screen either horizontally or 
vertically while maintaining aspect ratio
Seamless Switching
Built-in 2D keystone and geometry correction
Auto-scaling
Auto-de interlacing
Edge blending
Warping
Tiling (support for up to 3x3 arrays)
Blanking and Image positioning
Brightness, contrast, color, and uniformity 
user settable control
Image orientation Can display image front/rear, normal/inverted (ceiling)
Electronics HW access All accessible electronics are mounted from the back of the projector
Number of option cards 6 user inter-changeable – hot swappable
Number of processor cards 2 user inter-changeable
Number of option slots 4, located at back of projector for option cards; 1, located at back of 
projector for processor card
Native format adjustment Optional global aspect ratio setting can be set for projector allowing for 
automatic scaling of all input images to required output format
Arbitrary Gamma User definable gamma curves  
						

							Section 7: Specifications
Mirage M Series User Manual7-7020-100575-02  Rev. 1  (11-2010)
7.3 Image Processor Performance
7.4 Input (Source Signal) Compatibility 
7.4.1 Analog (Only) Input
7.4.2 Twin HDMI Input
7.4.3 Dual Link DVI Input
Min input pixel rate 13 Mpix/s
Max input pixel rate 330MHz over dual link DVI-D
Max input resolution 2048x1536 (QXGA)
Min input resolution 640x400
Max input frame rate with 
Standard Image Processor 
Card59Hz at 2560x1600 (QXGA) * * With sources that can output minimum 
blanking, otherwise lower vertical rates
Processing 10 bit throughout * * Except Dual-DVI input in dual-link mode 
(dual 8 bit input paths into 10 bit processing)
Source switching time Seamless switching with switch 
time less than 1 second
Connectors 5 female BNC, 75 Ohm
R/Pr
G/Y
B/Pb
H/C
V
Color spaces/signal types RGB
YPbPr
A/D conversion 10 bits
Connectors 2 independent HDMI inputs type A
2 loop-out connectors type A
Color spaces/signal types RGB
YCbCr (4:2:2)
YCbCr (4:4:4)
HDCP support
HDMI 1.3 supported (not including audio) except: 
12 bit color dithered to 10 bits; 16 bit color not 
supported
Connectors 1 dual link DVI-I, 300MHz
1 analog 15-pin VGA
NOTE: VGA is supported for mono signals or part 
of a dual input 3D signal.
Color spaces/signal types HDCP support
A/D conversion 10 bits for single link DVI input
8 bits for dual link DVI inputs
Frequency 165 MPixel/s analog 
						

							7-8Mirage M Series User Manual020-100575-02  Rev. 1   (11-2010)
Section 7: Specifications
7.4.4 Video Decoder Input
7.4.5 Dual SD/HD-SDI
7.5 Control Signal Compatibility 
7.5.1 Projector Control
7.5.2 Control Receiver
7.5.3 RS-232
Connectors 2 S-Video 4-pin miniature DIN
4 BNC, 75 Ohm 
2 independent decoder channels for PIP
Color space/Signal types Composite video
Component video (SD and ED only)
S-video
Video Standards NTSC, NTSC 4.43, PAL, PAL M, PAL N, PAL 60, 
SECAM
A/D conversion 10 bits
Connectors BNC, 75 Ohm
Color spaces/signal types Dual HD input
SDI, HDSDI
Number of transmitters 2 IR 
Modulation frequency Dual frequency (38 kHz, 455 kHz)
Wavelength (peak intensity) 950 nm
Range Min 35 m
Wired Keypad
Wire connection (option) 3 pin XLR
Max cable length 30 m 
XLR Connections Optional boot for remote with XLR connector built-
in to avoid requirement to use phono-to-XLR 
adaptor cable
Number of sensors 1 front, 1 rear 
Coverage 130 degrees coverage in-line with lens at 3 m 
distance
Modulation (carrier) frequency  Dual frequency (38 kHz, 455 kHz)
Number of ports 2
Connector 1 female 9-pin Dsub (IN)
1 male 9-pin Dsub (OUT)
Max bit rate 115.2 kbps
Flow control Xon/Xoff 
						

							Section 7: Specifications
Mirage M Series User Manual7-9020-100575-02  Rev. 1  (11-2010)
7.5.4 RS-422
7.5.5 Ethernet
7.5.6 USB 2.0 Device Port 
7.5.7 GPIO
7.5.8 Built-In Keypad and Display
7.5.9 AMX/Crestron Support
7.6 Power Requirements
Number of ports 1
Connector 1 female 9-pin Dsub
Max bit rate 115.2 kbps
Power output 12 V ±5% @ 400mA maximum
Number of ports 1
Standard 10/100 Base-T
Connector Female RJ-45
Number of ports 1
Standard Supports: mass storage device type, Ethernet 
device type, and/or serial device type.
Connector USB type B (full size)
Max bit rate 3-12 Mbps (high speed 480 Mbps not supported)
Number of I/O Lines 7
Connector Male 9-pin Dsub
Output sink current (logic low) 100 mA @ 1V typical
Power output 12 V ±5% @ 400mA maximum
Key type  Soft-touch keys
Display type Graphics LCD backlight
AMX Device Discovery Partner
Crestron Integrated Partner
Rated voltage  100 VAC – 240 VAC
Rated Current (dual lamp operation)                
370W 1080p 12 A @ 100 VAC
200W 1080p 9 A @ 100 VAC
370W SXGA+ 12 A @ 100 VAC
200W SXGA+ 9 A @ 100 VAC
370W WUXGA 12 A @ 100 VAC
200W WUXGA 9 A @ 100 VAC
Line frequency 50/60 Hz
AC Input Coupler 15 A, 250 VAC
Type of connector IEC 320-C14 with wire cable clamp
Line Cord 14AWG type FT1 with plug, NEMA 5-15P, 15A
Inrush Current 60 A max 
						

							7-10Mirage M Series User Manual020-100575-02  Rev. 1   (11-2010)
Section 7: Specifications
7.6.1 Lamp Specification
7.7 Physical Specifications
7.7.1 Size
Maximum Power Consumption Dual Lamp Single Lamp
370W 1080p 1320W 831W
350W 1080p 1267W 805W
300W 1080p 1135W 739W
200W 1080p 871W 607W
150W 1080p 739W 541W
370W SXGA+ 1320W 831W
350W SXGA+ 1267W 805W
300W SXGA+ 1135W 739W
200W SXGA+ 871W 607W
150W SXGA+ 739W 541W
370W WUXGA+ 1320W 831W
350W WUXGA+ 1267W 805W
300W WUXGA+ 1135W 739W
200W WUXGA+ 871W 607W
150W WUXGA+ 739W 541W
Maximum Current at 100V
370W 1080p 13.2 A 8.3 A
350W 1080p 12.7 A 8.0 A
300W 1080p 11.4 A 7.4 A
200W 1080p 8.7 A 6.1 A
150W 1080p 7.4 A 5.4 A
370W SXGA+ 13.2 A 8.3 A
350W SXGA+ 12.7 A 8.0 A
300W SXGA+ 11.4 A 7.4 A
200W SXGA+ 8.7 A 6.1 A
150W SXGA+ 7.4 A 5.4 A
370W WUXGA 13.2 A 8.3 A
350W WUXGA 12.7 A 8.0 A
300W WUXGA 11.4 A 7.4 A
200W WUXGA 8.7 A 6.1 A
150W WUXGA 7.4 A 5.4 A
Type Mercury Lamp (Hg)
Power
350W HD/350W SX+/350W WU/350W  300 W min., 370 W max (software adjustable)
200W HD/200W SX+/200W WU/200W   150 W min., 200 W max (software adjustable)
Warm-up time (to full output) 5 minutes max
Operating position ±20 deg max tilt of lamp axis from horizontal
Maximum product dimensions (L x W x H)
(with lens removed)561mm (22.1”) x 500mm (19.7”) x 247mm (9.75”)
Maximum shipping dimensions (L x W x H) 775mm (30.5”) x 698.5mm (27.5”) x 584mm (23”) 
						

							Section 7: Specifications
Mirage M Series User Manual7-11020-100575-02  Rev. 1  (11-2010)
7.7.2 Adjustment
7.7.3 Weight
7.7.4 Operating Position
7.8 Reliability and Serviceability
7.8.1 Reliability
7.8.2 Serviceability
7.9 Environment
7.9.1 Temperature/Humidity/Altitude
Product Alignment 2” of vertical adjustment on 2 front feet
1” of vertical adjustment on single rear foot
Maximum product weight (with lens removed) 25kg (55lb.) 
Maximum shipping weight (includes packaging) 40kg (87lb.)
Horizontal ±20 degrees allowable rotation about lens axis
Inverted ±20 degrees allowable rotation about lens axis
Rotation ±180 degrees perpendicular to lens axis
MTBF – excluding consumable components 15,000 hrs
Consumable components Air filters, fans, lamps
Time to replace any option card 1 minute 
Time to replace lamp 1 minute
Time to replace projection lens 30 seconds 
Time to replace air filter 1 minute 
Operating temperature range 5 to 40 degrees C 
Storage temperature range -40 to 70 degrees C
Humidity range 10% to 80%, non condensing
Operating Altitude 10,000 ft. maximum 
						

							7-12Mirage M Series User Manual020-100575-02  Rev. 1   (11-2010)
Section 7: Specifications
7.10 Accessories and Service Components
7.10.1 Service Components
7.11 Regulatory 
This product conforms to the following regulations related to product safety, environmental requirements and 
electromagnetic compatibility (EMC).
• FCC Part 15, Subpart B Class A; CISPR22/EN55022; CISPR24/EN55024
• UL 60950-1 First Edition; CAN/CSA-C22.2 No. 60950-1-03 First edition;
• IEC60950-1:2001
• 2002/95/EC RoHS
Product NamePart NumberSold With ProductSold Separately
Dual Image Processor 108-316101-XX X X
Analog Input 108-309101-XX X
Dual Link DVI Input 108-312101-XX X X
Dual SD/HD-SDI Input 108-313101-XX X
Twin HDMI Input 108-311101-XX X
DMX512 Interface 108-314101-XX X
Air Filter Dust 118-100104-XX X
Air Filter Fog 118-100105-XX X
Stacking Frame 118-100107-XX X
Ceiling Mount 118-100108-XX X
Lens ILS 0.73:1SX+/0.67:1HD 118-100110-XX X
Lens ILS 1.25-1.6SX+/1.16-1.49HD 118-100111-XX X
Lens ILS 1.5-2.0SX+/1.4-1.8HD 118-100112-XX X
Lens ILS 2.0-2.8SX+/1.8-2.6HD 118-100113-XX X
Lens ILS 2.8-4.5SX+/2.6-4.1HD 118-100114-XX X
Lens ILS 4.5-7.5SX+/4.1-6.9HD 118-100115-XX X
Lens ILS 7.5-11.2SX+/6.9-10.4HD 118-100116-XX X
Lens ILS 1.2SX+/1.1HD 118-100117-XX X
Lens ILS 1.2SX+/1.1HD 118-101103-XX X
Portrait Adapter 118-116109-XX X
Module IR Keypad w/Laser 002-100005-XX X X
HARN Wired Keypad External 001-100704-XX X X
User Manual 020-100575-XX X
Service Manual 020-100551-XX X
AutoSTACK 108-308101-XX X
Service ItemPart Number
Lamp (200W) 003-100856-XX
Lamp (350W) 003-100857-XX
Air Filter Dust M Series (Package of 6) 118-100104-XX
Air Filter Fog M Series (Package of 6) 118-100105-XX