Christie Projector J Series 1000W & 1200W User Manual

J Series 1000W and 1200W User Manual1-1020-100706-02  Rev. 1  (03-2014)
1 Introduction
Every effort has been made to ensure the information in this document is ac curate and reliable; however, due to 
constant research the information in this do cument is subject to change without notice.
USERS/OPERATORS:  This manual is intended for trained us ers operating professional high-brightness 
projection systems. Such users may also be trained to replace the lamp and air filter, but cannot install the...

1-2J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   (03-2014)
Section 1: Introduction
1.3 Projector Overview
The J Series is a family of high resolution video/graphics 3 chip 1080p HD, SXGA+, and WUXGA projectors; 
see  Table 1.3 J Series Projectors . These projectors are based on DLP® technology provided by Texas 
Instruments. 
1.3.1 How the Projector Works
The projector accepts data/graphics an d video input signals for projection onto front or rear screens. Light is 
generated by a xenon...

Section 1: Introduction
J Series 1000W and 1200W User Manual1-3020-100706-02  Rev. 1  (03-2014)
1.3.4 Key Features
• Up to 9,300 lumens
• HD (1080p), or SXGA+ or WUXGA resolution
• Xenon lamp with 1000W or 1200W options
• 10-bit image processor electronics with modular design
• Active fan control for minimum noise level
• User interchangeable projection  lenses with no-tool mounting
• LiteLOC ™ for constant brightness maintenance
• Intelligent Lens System (ILS) 
• Motorized lens mount for all models
•...

1-4J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   (03-2014)
Section 1: Introduction
1.4 Safety Warnings and Guidelines
1.4.1 General Precautions
  HIGH BRIGHTNESS. Never look directly into the projector lens. The extreme high 
brightness can cause permanent eye damage.
  Always power down the proj ector and disconnect all power sources before servicing 
or cleaning.
  FIRE HAZARD. Keep hands, clothes and all combustible material away from the  concentrated light beam of the projector....

Section 1: Introduction
J Series 1000W and 1200W User Manual1-5020-100706-02  Rev. 1  (03-2014)
1.4.2 AC /Power Precautions
  Use only the AC power cord supplied. Do not attempt operation if the AC supply and 
cord are not within the specified voltage an d power range. Refer to the license label 
on the back of the projector or 
Section 7 Specifications for rated voltage and power.
  The projector is equipped with  a 3-wire plug with a grounding pin. This is a safety 
feature. If you are unable to insert...

J Series 1000W and 1200W User Manual2-1020-100706-02  Rev. 1   (03-2014)
2 Installation and Setup
This section explains how to install, connect and optimize the projector for delivery of superior image
quality. Illustrations are graphical  representations only and are provided  to enhance the understanding of
the written material. 
2.1 Projector Quick Setup and Installation
The following instructions  are for those preferring a quick setup.  Refer to the remaining subsections for 
detailed setup...

2-2J Series 1000W and 1200W User Manual020-100706-02  Rev. 1  (03-2014)
Section 2: Installation and Setup
2. Align the lens interface plate with the lens mount. Align the lens electrical connector with the mating 
connector on the lens mount. Fully  insert the assembly straight into the lens mount opening without 
turning. Press using your hand as shown in Figure 2-2 . 
NOTE: When installing the lens, ensure that the 
lens is not inserted at an angle, as this can cause damage.
FIGURE 2-2 
3. While...

Section 2: Installation and Setup
J Series 1000W and 1200W User Manual2-3020-100706-02  Rev. 1   (03-2014)
FIGURE 2-4 
6. Use a 5mm hex driver to fasten the red security screws provided with the lens mount (Figure 2-4 ). 
NOTES:  1)  Recommended for heaviest lenses such as 0.73:1 and 1.2:1 . 2)  The red security screws MUST 
be installed when hoisting the projector overhead,  or installing the projector in an overhead position.
  Use of the lens red security screws or the lens retaining screws is...

2-4J Series 1000W and 1200W User Manual020-100706-02  Rev. 1  (03-2014)
Section 2: Installation and Setup
•Video Decoder Input Card : depending on the source you can apply the following;
• Composite video source to 1-CVBS, using a BNC Cable 
NOTE:  Same signal can be used on 4, 5 or 6 when 
input is selected as CVBS.
• A component signal on Inputs 4(Pr), 5(Y), 6(Pb) using BNC Connectors. 
NOTE:  Grouped as a component 
input, YPbPr .
• S-Video to one of the two, 2-SVID or 3-SVID using S-Video cable.
•...