Christie Projector DWX600-G User Manual

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 2: Introduction
2-3
Right View
LAMP
Left View
1
2
3
4
Ind. Part NameDescription
1 Lamp Door Use the lamp door to access the lamp module.
2 LED Status Indicators Displays the status of the projector. They are (from left 
to right): LAMP, STATUS, and PIC MUTE.
3 Built-in Keypad Controls the projector.
4 Cooling Air Vents 
(Intake) Keep these vents unobstructed to prevent the projector 
from overheating. 

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 2: Introduction
2-4
2.2  Built-in Keypad
7
8
9
102
4
5
611
1
3
Ind. Key Name
Description
1 Power Turn the projector on or off
2 Menu Display menus
3 Enter Confirm a selection
4 Auto Automatically optimize image
5 Lens Adjust the lens vertical or horizontal offset setting
6 Focus Adjust focus
7 Exit Return to previous level or exit menus if at top level
8 Arrow Keys  
y Adjust a setting UP or DOWN
 
y Navigate within a menu
9 Input Select an...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 2: Introduction
2-5
2.3  Input/Output (I/O) Panel
Ind.Connector Name Ind.Connector Name
1 Remote IN 8Mini USB
2 Remote OUT 9 USB Type A
3 Component IN 10 DisplayPort
4 CVBS 11 HDMI
5 S-Video 12 VGA-IN
6 RS232 13 VGA OUT
7 Ethernet 14 DVI
1 2 3 4 5
78 9
1011 12 13 14
6 

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 2: Introduction
2-6
2.4  Remote Control
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15 16
17
18
19
20
21
22
23
24
25
26
27
28
29 

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 2: Introduction
2-7
Ind. Key NameDescription
1 Picture Mute Display or blank the video image.
2 Power on Turn projector ON.
3 Gamma Adjust mid-range levels.
4 Bright Adjust amount of light in the image.
5 PIP/PBP Turn PIP/PBP ON/OFF.
6 Size Adjust the PIP/PBP size
7 Number Keys Enter a number, such as a channel, value, etc.
8 Help Display context-sensitive help.
9 Menu Display menus.
10 Arrow Keys  
y Adjust a setting UP or DOWN.
 
y Navigate...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 2: Introduction
2-8
2.5  LED Status Indicators
The LED status indicators are located on the right side of the projector\
. Each 
LED is defined below. 
y LAMP LED
LED Status
Projector State
Red (short blink) Failed to strike lamp after 5 attempts (strike attempts will 
stop).
Lamp has unexpectedly shut down (system goes into cool 
down state). 
Yellow (no blink) Lamp time has expired and lamp should be replaced. 
(projector also begins to...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 2: Introduction
2-9
 
y PICTURE MUTE LED
LED Status
Projector State
Green Picture mute is off – image is displayed
Yellow Picture mute is on – image is black 

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-1
3.  INSTALLATION
3.1  Connect to Computer
NOTE: 
™The diagram shows the cables/connectors that may be used to connect to v\
arious devices.  
™Due to the difference in applications for each country, the accessories \
required in some regions may be different from those 
shown.
 
™This diagram is for illustrative purposes only, and does NOT indicate th\
at these accessories are supplied with the projector.
Ind....

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-2
3.2  Connect to Video Equipment
NOTE: 
™The diagram shows the cables/connectors that may be used to connect to v\
arious devices.  
™Due to the difference in applications for each country, the accessories \
required in some regions may be different from those 
shown.
 
™This diagram is for illustrative purposes only, and does NOT indicate th\
at these accessories are supplied with the projector.
Component video...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-3
3.3  Turn the Projector On
1.  Ensure that the power cord and signal cable are securely connected. The \
Power button on the built in keypad is illuminated. 12345678910111213141516171819202.  Turn on the lamp by pressing “” on the remote control or press “” on 
the built-in keypad. The Status LED is yellow with a long blink. 
1234567891011121314151617181920 
The startup screen displays in approximately 10 seconds. 
3.  Turn...