Christie Projector DWX600-G User Manual

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-12
 
y Serial Port Echo: Control whether the serial port echoes characters.
 
y Projector Address: Set the projector address (0-9). The projector will\
 
respond to IR remotes set either at the same address as the projector or\
 to 
IR remotes set to address 0.
Image Blending
Adjust blend widths and settings to left, right, top and/or bottom sides to create 
a seamless multi-projector stitched image. (Available only when optiona\...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-13
Color Matching
You may require a unique color gamut (range) for a single projector or\
 
application, or you may need to precisely match colors across multiple 
adjacent displays. Use Color Matching by Meter Adjustment or by Manual 
Adjustment to define the precise hue of each primary color component (red, 
green, blue and white).
The x/y coordinates for each color define its location on the standard CIE 
chromaticity graph....

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-14
 
y Manual Adjustment
1.  Adjust color slide bars and judge image color by eye or meter. A user- defined color “adjustment” can be applied.
2.  Use this submenu if you do not have specific color coordinates in 
mind and will judge color performance by eye or meter. As for Meter 
Adjustment, each color control actually defines new x/y coordinates for 
that color and changes its hue. The main colors (red part of red, green\...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-15
4.4  Lamp Menu
Lamp Mode
Select Constant Power, Constant Intensity or ECO mode. When in ECO 
mode, the projector will adjust to the lowest fan speed and switch the l\
amp 
power to the minimum setting.
Constant Power
Set the value of the lamp power (in Watts).
Constant Intensity
Set the value for the Constant Intensity to maintain constant brightness\
. 
The light sensor will monitor the light level and will apply more power \...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-16
4.5  Status Menu
The read-only Status menu lists a variety of details about the standard \
and 
optional components currently detected in the projector.
For DHD Models 

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-17
For DWU Models 

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-18
For DWX Models 

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-19
4.6  Input Switching & PIP Menu
Main Input
From the list of active inputs, select one to be used as the main image.\
PIP/PBP Input
From the list of active inputs, select one to be used as the PIP/PBP.
PIP/PBP Enable
Toggle between displaying two sources at once (Main and PIP/PBP images)\
 
or one source only. The check box turns the PIP/PBP source ON and OFF. 
Refer to Section 6.2 for the Main and PIP/PBP compatibility table....

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-20
NOTE: 
™PIP/PBP layout and size table as described below. 
™P : indicates primary source region (lighter color). 
™* : Both source regions are the same size.
PIP/PBP Layout PIP/PBP Size
Small Medium Large
PBP, Bigger Left
PPP *
Over-Under, Bigger Upper
PPP *
PBP, Bigger Right
PPP *
Over-Under, Bigger Lower
PPP *
PIP-Bottom Right
PPP
PIP-Bottom LeftPPP
PIP-Top LeftPPP
PIP-Top RightPPP
Timing Detection
Select...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-21
4.7  Language Menu
Allows you to select an available language for the OSD display.
4.8  Test Pattern Menu
Choose the desired internal test pattern to display, or select OFF to tu\
rn off a 
test pattern. 
y OFF
 
y Black
 
y White
 
y Checkerboard
 
y Grid
 
y Color Bars
Input Key
Use it to list all of the sources or change the sources.