Christie Digital Systems Lx501, Lx601i Users Manual

19LX501/LX601i User Manual-Operating Guide 020-000461-01 Rev. 1 (03-2012)
30°3m30°
30°
30°3m
(approx.)
About the remote control signal
The remote control works with the 
projector’s remote sensor. This projector 
has two remote sensors on the front and 
back sides.
The sensors can sense signals within 
the following range:
60 degrees (30 degrees to the left and right of the 
sensor) within 3 meters about.
• You can deactivate one of the sensors using the REMOTE RECEIV. 
item in the SERVICE menu of the...

20LX501/LX601i User Manual-Operating Guide 020-000461-01 Rev. 1 (03-2012)
Using as a simple PC mouse & keyboard
The accessory remote control works as a simple 
mouse and keyboard of the computer, when the 
projector’s USB TYPE B port and the computer’s 
type A USB port are connected and MOUSE is 
selected for the USB TYPE B item in the OPTION 
menu (
66).
(1) PAGE UP key: Press PAGE UP button.
(2) PAGE DOWN key: Press PAGE DOWN button.
(3) Mouse left button: Press ENTER button.
(4) Move pointer:  Use...

21LX501/LX601i User Manual-Operating Guide 020-000461-01 Rev. 1 (03-2012)
  In a normal state  
The Status Monitor displays the state of the projector 
in three lines.
:  Displays the status of the projector. 
While the lamp is on, the selected port is 
displayed.
Displayed status is as below;
STANDBY: The projector is in standby mode.
WARM UP: The projector is warming up.
SEARCHING: The projector is searching an input signal.
COOL DOWN:  The projector is cooling down.
:  Displays the status of the...

22LX501/LX601i User Manual-Operating Guide 020-000461-01 Rev. 1 (03-2012)
Status Monitor  
  In error state 
The Status Monitor displays a warning of an error 
with larger letters. Resolve the errors referring to the 
table of the sections "Related messages"
 (11 3) and 
"Regarding the indicator lamps" 
(11 4, 11 5) when the 
warning is displayed. 
Displayed warnings are as below;
COVER: The lamp cover has not been properly fixed. 
Refer to the LAMP indicator blinking in the table 
(11...

23LX501/LX601i User Manual-Operating Guide 020-000461-01 Rev. 1 (03-2012)
When the projector is in a normal condition, 
or dislays one of the warnings of AIR FLOW, 
COLD or FILTER errors, press the FUNCTION 
button on the control panel or press the ENTER 
button on the remote control for three seconds. 
The backlight of the monitor turns on.
  To display the setup information including 
usage time
Use the ◄/► buttons to switch display. 
    
  
Usage time: The Status Monitor displays 
the lamp time...

24LX501/LX601i User Manual-Operating Guide 020-000461-01 Rev. 1 (03-2012)
AC240V35°C
7FILTERERRO
1PREVIOUS
  To display error history 
Press the ▲ button to display previous error 
log. If a warning has been displayed, the 
first previous error log is the present error 
currently occurring. The Status Monitor 
displays the log number, occurred error, the 
supplied voltage and peripheral temperature 
at that time. Press the ► button to display 
the usage time when each error occurred. 
Use the ▲/▼ buttons...

25LX501/LX601i User Manual-Operating Guide 020-000461-01 Rev. 1 (03-2012)
1.Make sure that the power cord is firmly 
and correctly connected to the projector 
and the outlet.
Turning on the power
2.Make sure that the POWER indicator is 
lighted in steady orange (
11 4). Then 
remove the lens cover.
3.Press STANDBY/ON button on the projector  
or the ON button on the remote control.
The projection lamp will light up and POWER indicator will begin blinking in 
green. When the power is completely on, the...

26LX501/LX601i User Manual-Operating Guide 020-000461-01 Rev. 1 (03-2012)
Operating
Operating
1.
Adjusting the volume
Use the VOL + / - buttons to adjust the volume. 
A dialog will appear on the screen to aid you in 
adjusting the volume. If you do not do anything, 
the dialog will automatically disappear after a few 
seconds.
• 
When  is selected for current picture input port, the volume 
adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (
56).
• Even if the projector is in the...

27LX501/LX601i User Manual-Operating Guide 020-000461-01 Rev. 1 (03-2012)
Operating
1.Press INPUT button on the projector. 
Each time you press the button, the projector 
switches its input port from the current port as 
below.
Selecting an input signal
1.Press COMPUTER 1 / 2, LAN, USB TYPE A / B, HDMI 1 / 2, COMPONENT, 
S-VIDEO or VIDEO button on the remote control. 
The port corresponding to each button is selected as below.
Button Ports
COMPUTER 1 COMPUTER IN1
COMPUTER 2 COMPUTER IN2
LAN LAN
USB TYPE...

28LX501/LX601i User Manual-Operating Guide 020-000461-01 Rev. 1 (03-2012)
Operating
Selecting an aspect ratio
  For a computer signal
 NORMAL  
4:3 
 
16:9 
 
16:10 
         
  For a video signal, s-video signal or component video signal
 4:3 
 
16:9 
 
14:9 
  
   For an input signal from the LAN, USB TYPE A or USB TYPE B ports, or 
if there is no signal 
  4:3 (fixed)
1.Press ASPECT button on the remote control.   
Each time you press the button, the projector switches 
the mode for aspect...