Christie Digital Systems Ds+5k, Kc-8k, Dw3k-6k, Kc, Mirage S+2-4-8k, Dlv1400-dx, Matrix 4000 Users Manual

							Section 2: Installation and Setup 
 
   User’s Manual     2-15. 
As an alternative to the projector’s keypad or remote, you may wish to communicate 
with the projector using a PC or other controller. Such a device sends commands and 
receives feedback via serial links (RS232 and RS422), Ethernet or GPIO 
communications to the projector, all described below. 
As desired, direct the projector’s IR remote keypad towards the display screen or the 
projector’s IR sensors. Alternatively, connect a wired (tethered) version of the remote 
to the 3.5mm RCA jack labeled as 
REMOTE on the projector’s input panel. Note that 
response to a wired keypad must also be enabled in the Communications menu—see 
3.6, Adjusting System Parameters and Advanced Controls for more information. 
There are two types of serial ports available on the projector: RS232 and RS422. You 
can connect a device with a serial interface, such as a computer to either of these 
connectors (not both) and control the projector remotely by entering specific serial 
communication commands.  
Connecting RS-232 
The two 9-pin DIN connectors labeled RS232 IN and RS232 OUT on the input panel 
are dedicated to serial communication (see Figure 2.10). Using the appropriate serial 
communication cables (see Appendix C) connect the controlling source, such as a 
personal computer to the RS232 IN connector. Then set the baud rate to match that of 
the computer. Refer to Section 3 for details on changing the projector’s baud rate. 
 
Figure 2.10. Connecting RS232 
Connecting RS-422 
If you wish to control the projector with a computer and or other controlling device 
with RS-422 capability, connect a RS-422 serial communication cable between the 
computer and the RS-422 port on the projector (see Figure 2.11). RS-422 is better 
suited for serial communication over long distances then is RS-232 communication.  
 Use the RS-422 port only if your device had RS-422 capability – always consult 
the literature provided with your equipment before connecting. Connecting to the RS-
422 port with incompatible equipment could damage your projector. 
2.4 Connecting 
Communications 
 Remote Keypads '
  Serial Port Connections ' 
						

							Section 2: Installation and Setup 
2-16     User’s Manual 
    
 
Figure 2.11. Connecting RS422 
 
Ethernet Communications 
To add the projector to an existing Ethernet network with other equipment such as 
controllers and other projectors, connect standard CAT5 Ethernet cable between your 
Ethernet controller (or hub) and the Ethernet port on the side of the projector. 
Upon connection to an Ethernet network, the projector’s factory default IP address of 
0.0.0.0.0 will automatically enable the DHCP function (if available on the network) to 
assign a new IP address that is valid and unique for that network. Or, if there is no 
DHCP function available on the network  (or if a specific static IP address for the 
projector is preferred or required), you can set the address in the Ethernet Settings 
menu or via an ASCII serial command. 
Regardless of how it is assigned, once a projector has a valid and unique address it 
will respond to commands sent to this address. To determine the projector’s current IP 
address, consult the Status or Communications menus. 
Refer to Section 3 for further information about setting up and using a projector 
connected via Ethernet. 
Log on to www.christiedigital.com for detailed information on ChristieNET. 
 
RS-232 NETWORK: If you want to connect multiple projectors in a network with serial 
communication, connect the controlling source to the RS232 IN connector of the first 
projector in the network. Then take another serial communication cable and connect 
one end to the RS232 OUT connector and the other end to the RS232 IN connector of 
the next projector. Continue this pattern of connection with all projectors in the 
network. The last projector in the network will only have a connection to the RS232 
IN connector. See Figure 2.12.  Ethernet Communications 
'
 Connecting Multiple '
 Projectors  
						

							Section 2: Installation and Setup 
 
   User’s Manual     2-17. 
 
Figure 2.12. 
MIXED NETWORK: To control multiple projectors with a computer/controller having an 
RS422 interface, first set them all to the same baud rate as your RS422 controller. 
NOTE: You must enable this combination of RS422 and RS232 in the 
Communications menu. Set the “Network Routing” option to “RS232 and RS422 
Joined”. See Section 3 for details. 
Then chain the projectors together by connecting an 
RS232 port of the first projector 
(already connected to the computer/controller through the 
RS422 port) to an RS232 
port on the next projector in the chain. Continue connecting projectors in this manner 
until you’ve reached the last projector in the chain, so that only the last projector has 
one unused 
RS232 port. See Figure 2.13. 
 
Figure 2.13. 
Note that communication parameters such as baud rate must be set to match the 
particular controlling device before connecting as a network—refer to the 
documentation that came with your controlling device in order to determine the proper 
baud rate. See 3.6, Adjusting System Parameters and Advanced Controls if you need 
help changing the projector baud rate. In addition, set the Network Routing to “RS232 
and RS422 Joined” if you want to reach all projectors. 
NOTES: 1) To avoid damage, connect only properly wired serial communication 
cables. See Appendix C for details. 2) It is recommended that each RS232 
communication cable be no more than 25 feet in length. Use high quality cables.  
						

							Section 2: Installation and Setup 
2-18     User’s Manual 
    
ETHERNET NETWORK SETUP: To add one or more projectors to an Ethernet network, 
use standard CAT5 cable to connect each projector’s Ethernet port to a hub belonging 
to the network. A controller or PC must also be connected to the hub. See Figure 2.14. 
 
Figure 2.14. 
SETTING THE PROJECTOR’S IP ADDRESS: Upon connection to most Ethernet 
networks, each projector’s factory default IP address of 0.0.0.0 triggers the network’s 
DHCP (Dynamic Host Configuration Protocol) server function to automatically assign 
an IP address that is valid and unique for use on that network. Depending on the 
network, this DHCP-assigned IP address usually remains stable for a single session, 
but may change with subsequent power-ups and logins. On some networks, the 
address will remain stable from session to session. In all cases, the projector’s IP 
address and port appear in the Status menu as well as the Ethernet Settings submenu. 
See Figure 2.15. 
 
Figure 2.15. Setting the Projector’s IP Address 
Note that if a projector’s IP address is anything other than 0.0.0.0  (shown as 
000.000.000.000 in the Ethernet Settings menu) upon connection to an Ethernet 
network, or if DHCP is not available on the network, the automatic DHCP server 
function for supplying a valid and unique IP address to the projector is disabled. 
Instead, a specific and static IP address must be defined in projector memory—enter 
the new address in the Ethernet Settings submenu, or send to the projector via a serial 
command. The IP address will be in effect until it is changed again, or until the DHCP 
checkbox is re-enabled for use with a DHCP server on the network. 
CHANGING THE PORT#: On some Ethernet networks, firewall restrictions may require 
that the port number of the projector be changed from its default of 3002. If so, enter a 
new port number in the Ethernet Settings menu or include the new port# in an XIP 
serial command sent to the projector. It is highly recommended not to use a port# 
below 1000, as these ports are typically reserved for and used by common IP 
applications.   
						

							Section 2: Installation and Setup 
 
   User’s Manual     2-19. 
SUBNET MASK AND DEFAULT GATEWAY: The Subnet Mask and Default Gateway are 
automatically assigned when DHCP is enabled. If a static IP is being used, it must be 
assigned before the subnet mask. The Default Gateway is an optional router device 
used to send and receive data outside the subnet. 
 
ArtNet INTERFACE SETTINGS:  Refer to Section 3.6 – Adjusting System Parameters 
and Advanced Control, System Configuration – Communication for additional 
information about ArtNet settings.  
By default, communications originating from one type of serial controller—RS232 vs. 
RS422 vs. Ethernet—stay on the corresponding network path. A “Separate” setting 
indicates this separation for “Network Routing” in the Communications menu. If you 
are using an RS422 controller, for example, it will communicate only with the 
projector to which it is connected unless you change this setting to either “RS232 and 
RS422 Joined” or “All Joined”. 
To relay all messages to all ports—RS232, RS422, and Ethernet—set the “Network 
Routing” option in the Communications menu for each projector to “All Joined”. This 
configuration is useful if you are using a non-RS232 controller with the RS232 linking 
available between these projectors. For example, you may want to use both an RS422-
compatible controller and an Ethernet-connected PC for working with a network of 
projectors linked via their RS232 in/out ports. 
 
Figure 2.16. 
To isolate just RS422 communications, select “RS232 and Ethernet Joined”. In Figure 
2.16, only projector #3 will respond to the RS422 controller. To isolate just Ethernet 
communications, select “RS232 and RS422 Joined”—only projector #1 will respond 
via Ethernet. 
The GPIO connector on the input panel can be used to provide a method of interfacing 
a wide range of external I/O devices to the projector.  
Refer to Appendix E: System Integration for complete details on pin configuration 
and how to program the various pins on the connector. 
 
   Se
parating Networks '
 Communicating to '
 All Ports 
2.5 System 
Integration - 
GPIO 
Connector  
						

							Section 2: Installation and Setup 
2-20     User’s Manual 
    
 The North American rated line cord is provided with each projector. Ensure 
that you are using a line cord that meets the appropriate rating standards (CCC 
for use in China, PSE for use in Japan).
 
Plug the line cord to the AC receptacle located at the back of the projector, below the 
input panel, and the 3-pronged end into a grounded AC outlet. Make sure the socket 
outlet is installed near the equipment and is easily accessible. The input voltage to the 
projector must be capable of 100 – 240 VAC in 500W and 1000W models and 200-
240VAC in 1200W models. (See also Section 6 – Specifications for complete details 
on all power requirements.) 
Use the approved North American-rated line cord supplied with the projector.  If you 
are connecting to an area outside of North America make sure you are using an 
appropriately rated line cord.  
Always power down the projector before unplugging the AC line cord. Wait 5-10 
minutes for the main exhaust fan to turn off and for the lamp to cool sufficiently 
before unplugging the projector.  
 WARNINGS  
Do not attempt operation if the AC supply and cord are 
not within the specified voltage and power range. 
Wait for the cooling fans to turn off before unplugging the 
projector. 
 
 
 
2.6 Power 
Connection  
						

							Section 3 
Operation  
 
   User’s Manual    3-1 
 
This section explains how to effectively operate the projector once it has been 
installed. It is recommended that you read this section and familiarize yourself with 
the components and the available menu options before you begin using your projector 
for the first time. 
 
 
  
The built-in keypad is located at the back of the projector, beside the input panel. Use 
it similarly to the IR remote to control the projector. A status LED display is also 
included on this keypad for monitoring projector status. 
The AC receptacle is located at the back of the projector just below the input panel. 
Use this outlet to plug in an appropriately rated line cord. Refer to Section 6 – 
Specifications for details.  
Located on the underside of the projector are two fully adjustable feet. Raise or lower 
these feet when positioning the projector to ensure it is level on all sides so the 
displayed image will appear rectangular without any keystone.  
NOTE: The third foot, located at the rear of the projector (underside) is not 
adjustable.   
Refer to Section 2 - Projector Position and Mounting for instructions on how to 
adjust the projector’s feet.  
3.1   About the 
Projector 
 Built-in Keypad  '
 AC Receptacle '
 Adjustable Feet ' 
						

							Section 3: Operation 
3-2     User’s Manual 
    
 
The projector is built with a motorized lens mount that allows for easy lens control 
and adjustment. This includes such functions as adjusting vertical and horizontal 
offsets, zoom and focus. The lens mount can be fitted with any one of the available 
optional lenses – see Section 6 - Specifications.  
• Zoom and Focus – There are two internal lens motors that allow for quick 
motorized adjustment of zoom and focus. Adjust zoom to fit the displayed 
image on the screen and adjust focus to improve the clarity of the image. 
NOTE: You can manually override zoom and focus adjustments set with the 
remote. Turn the outer ring on the projection lens to adjust focus and the 
inner ring to adjust zoom.  
• Lens Offset – Vertical and horizontal offset is performed on the lens mount 
through the use of DC motors.  
• Shutter – Standard on all models the shutter allows you to turn the screen 
absolutely black when in the “on” state. 
• Optical Aperture – Enables adjustment of light output and contrast ratio. 
NOTES: 1) The projection lens is shipped separately from the projector. 2) Use the 
lens cap when transporting the projector to avoid scratching and damaging the lens, 
which could affect your displayed image. 
All source connections are made to the input panel located at the back of the projector. 
Connect RGB or YPbPr sources to 
INPUT 1, analog or digital display signals to INPUT 
2
, composite video to INPUT 3, and S-video to INPUT 4. Any of the available optional 
modules can be installed in 
INPUT 5 and/or INPUT 6. 
There is no status display on the input panel. The only status display is part of the 
built-in keypad located at the rear of the projector. 
There are numerous air vents located around the projector. It is important these vents 
remain unobstructed. Adequate airflow through the projector will prevent it from 
overheating. 
The two IR sensors located on the projector receive transmissions from the IR remote 
from up to 100 feet away. It is important to keep the transmission path to these sensors 
unobstructed for uninterrupted communications with the projector. The front IR 
sensor is located next to the projector’s nameplate and the rear IR sensor is located at 
the back of the projector just above the status LED display. 
The lamp door is located at the back of the projector, which provides easy access to 
the lamp module for replacement. See Section 4 for lamp replacement procedures.              Lens Mount &
  
 Pro
jection Lenses '
 Input Panel '
 Cooling and Air Vents '
  Front & Rear IR Sensors '
 Lamp Door ' 
						

							Section 3: Operation 
 
   User’s Manual    3-3. 
 
 Laser radiation is emitted from the laser diode in the remote. Do not look 
directly into the beam of the remote.
 
 
The projector is typically controlled using one of the following keypads: 
• Built-in Keypad located at the back of the projector  
• Remote Keypad for tethered or tetherless control up to 100 feet away 
(includes cable for use as a wired remote) 
While each of the keypads provides complete control of the projector, they differ 
slightly in their arrangement of keys and in what functions can be accessed directly 
with a key press rather than requiring use of the menu system. You may find one 
keypad more convenient than another for your specific installation and application.  
NOTE: The remote keypad has a single IR protocol and can be converted to a wired 
remote by connecting the cable provided with the projector to the RCA jack labeled as 
REMOTE on the input panel.  
To control the projector when signals from a remote keypad cannot reach the 
projector, use the projector’s built-in keypad (Figure 3.1). The nearby LED display 
provides feedback indicating current status and activities of the projector. Because the 
built-in keypad 
has fewer keys 
than the remote 
keypad, certain 
projector 
functions are 
accessible only 
through the menu 
system rather than via a direct key.  
NOTE: The built-in keypad cannot be disabled. 
Refer to the key descriptions provided for the IR remote – see Figure 3.2. 
The IR remote keypad controls the projector by way of wireless communications from 
a battery-powered infrared (IR) transmitter. Use the IR remote keypad the same way 
you would use a remote keypad supplied with a TV or VCR. When making key 
presses, direct the keypad either toward the screen or toward the front or rear of the 
projector. One of the two IR sensors on the projector will detect the signals and relay 
the commands for internal processing. 
3.2 Using the 
Remote or 
Built-In Keypad 
 Keypad Commands '
 Built-in '
 
Figure 3.1.  Built-in Keypad  
 IR Remote ' 
						

							Section 3: Operation 
3-4     User’s Manual 
    
 
 
 
*These are toggle keys, which require you to press and hold or press twice or 
press and use the up/down arrow keys.  
NOTE: To turn the OSD off you must press 
OSD and . 
Figure 3.2. Remote Keypad