Christie Digital Systems Cp2215 User Manual

   Installation and Setup
CP2215 User Manual13020-101225-01 Rev. 1 (01-2014)
This diagram illustrates how to wire a GPIO cable to a server or a 3D device:
The recommended operating point is 5mA, the maximum current is 50 mA, and the forward voltage 
drop is 
~ 1 V (@ 5 mA).
Connect Devices to the SCCI Port
The Simple Contact Closure Port (SCCI) port is a DB-9 (male) connector located on the PIB input 
panel. The SCCI port controls a limited set of projector functionality through contact closures. This...

   Installation and Setup
CP2215 User Manual14020-101225-01 Rev. 1 (01-2014)
All SCCI inputs require a pulse input of 50ms to several seconds to operate reliably. Inputs are 5V 
resistor current limited LED’s inside of optocouplers.
The open-collector Health Output (PIN 8) circuit only draws power when a failure occurs or an 
interlock is activated.
Connect Power
1. If the projector is operating, turn it off and disconnect it from AC power.
2. Loosen the threaded bolt on the ground lug on the AC...

   Installation and Setup
CP2215 User Manual15020-101225-01 Rev. 1 (01-2014)
4. Insert a bare end of the protected earth wire into the hole on the top of the ground lug so it is 
beneath the threaded bolt.
5. Tighten the threaded bolt to 50 in-lb.
6. Connect the other bare end of the protected earth wire to the building ground.
7. Connect one end of the projector power cord to the AC receptacle on the lower-left rear corner of 
the projector and then connect the other end of the power cord to an AC...

   Installation and Setup
CP2215 User Manual16020-101225-01 Rev. 1 (01-2014)
Activate Marriage
You must complete marriage to display encrypted content and to comply with the Digital Cinema 
Initiatives (DCI) specification.  You cannot complete marriage remotely. In addition, an authorized 
employee must be physically present to verify that the anti-tamper seal on the firewall is unbroken, 
the projector is unaltered,   and to press the marriage button on the card cage faceplate.
1. Log on to the...

   Installation and Setup
CP2215 User Manual17020-101225-01 Rev. 1 (01-2014)
Add the Lamp Information to the Lamp History
1. If the lamp is on, tap the lamp off ( ) icon to turn it off.
2. Tap Menu > Advanced Setup > Lamp Change Wizard.
3. Tap Next.
4. Complete these fields:
5. Tap Save.
6. Tap Next.
Turn the Lamp On
On the projector touch panel controller (TPC) main screen, tap the lamp on ( ) icon.
Align the Lamp with LampLOC
To ensure optimal lamp performance and peak brightness at the screen for the...

   Installation and Setup
CP2215 User Manual18020-101225-01 Rev. 1 (01-2014)
2. Tap Menu > Advanced Setup > LampLOC Setup.
3. Tap Display Full Screen White Test Pattern.
4. Tap Do Auto.
Adjust the Image to Fit Your Screen
This procedure must be completed before you complete a boresight adjustment. 
1. Verify the projector is properly positioned relative to the screen. 
See Position the Projector on page 4.
2. Display a RGB-12bit-Full Screen White test pattern and center the image:
a. Tap the Test Pattern...

   Installation and Setup
CP2215 User Manual19020-101225-01 Rev. 1 (01-2014)
8. Display a full white test pattern:
a. On the TPC, tap the Test Pattern icon ( ) in the task bar.
b. Tap All Test Patterns.
c. Tap RGB-12bit-Full Screen White.
9. If the test pattern is focused and centered on the screen you do not need to complete further 
image adjustment. 
If the image is not focused and centered on the screen, complete one of these procedures:
a. If the image appears distorted and resembles a trapezoid,...

CP2215 User Manual21020-101225-01 Rev. 1 (01-2014)
Adjust the Image
This section provides information and procedures for adjusting the projector image.
Correct Keystone Effect
Keystone effect occurs when you project an image onto the screen at an angle and the projector is 
not centered on the screen. The image will appear distorted and resemble a trapezoid. This image 
identifies horizontal (A) and vertical (B) keystone effect. 
Horizontal keystone effect occurs when the projector is titled horizontally...

22                                                                                                                                                            CP2215 User Manual020-101225-01 Rev. 1 (01-2014)
Adjust the Image
Adjust Vertical Boresight Angle
It is recommended that you complete a top and bottom boresight adjustment before adjusting the 
horizontal boresight.
1. Display the DC2K Framing2 test pattern:
a. On the Touch Panel Controller, tap the Test Pattern icon in the task bar.
b. Tap DC2K...