Christie Digital Systems Cp2215 User Manual

   Installation and Setup
CP2215 User Manual3020-101225-01 Rev. 1 (01-2014)
Lamp Precautions
Projector Components - Front
• EXPLOSION HAZARD! Wear authorized protective safety gear whenever the lamp door is 
open! Never attempt to remove the lamp directly after use. The lamp is under significant 
pressure when hot and cold, and may explode, causing personal injury and/or property 
damage. Failure to comply results in death or serious injury.
• Any lamp used in the projector is under high pressure and...

   Installation and Setup
CP2215 User Manual4020-101225-01 Rev. 1 (01-2014)
Projector Components - Rear
Position the Projector
1. If you are installing the projector in the optional rack stand (P/N 108-416102-XX) follow the 
instructions provided with the rack stand to install it.
2. Position the projector so it is centered and parallel with the theatre screen. If space is limited, 
aim the projector slightly off-center and use lens offset to center the image on the screen. 
D Air Filter Cover and Air...

   Installation and Setup
CP2215 User Manual5020-101225-01 Rev. 1 (01-2014)
Adjust Tilt and Level the Projector
The front-to-back and side-to-side tilt of the projector must not exceed 15 degrees. 
1. Loosen the lock nut with a 3/4 in. or 19mm wrench. 
2. Turn the adjustable feet on the bottom of the projector 
clockwise or counter-clockwise 1/8th of a turn at a time to 
move the projector up or down.
When adjusting two or more feet at once, always adjust them 
the same amount. This keeps equal weight...

   Installation and Setup
CP2215 User Manual6020-101225-01 Rev. 1 (01-2014)
3. Tighten the mounting arm until it fits tightly on the ball joint. 
4. Connect the cable from the TPC to the connector located on the projector rear panel.
5. Tilt the TPC to adjust the viewing angle.
Connect the Exhaust Duct
You must install the optional duct (P/N: 119-103105-xx) if an air volume of 9,000 BTU (per hour) 
cannot be ventilated from the room in which the projector is installed.
When using an external duct, the...

   Installation and Setup
CP2215 User Manual7020-101225-01 Rev. 1 (01-2014)
Install the Lens
The lens seals the projection head, preventing contaminants from entering the main electronics 
area. Do not operate the projector without a lens installed. Install a lens plug when you install or 
transport the projector.
1. Move the lens clamp on the front of the projector to the open position.
2. Position the lens so the lens retaining ring mounts align with the lens mount. 
3. Remove the lens caps from the...

   Installation and Setup
CP2215 User Manual8020-101225-01 Rev. 1 (01-2014)
6. Move the lens clamp to the locked position. 
Install the Lamp
1. If the projector is operating, turn it off and allow it to cool a minimum of 15 minutes.
2. Turn the breaker switch for the projector off.
3. Disconnect the projector from AC power.
4. Put on your protective clothing, face shield, and gloves.
5. Insert the key in the lamp door lock, turn the key, and open the lamp door. 
6. Loosen the 2 thumbscrews (A and B) and...

   Installation and Setup
CP2215 User Manual9020-101225-01 Rev. 1 (01-2014)
7. Loosen the cathode screw (D) with the 5 mm hex key attached to the lamp door.
8. Install the lamp:
a. Remove the tape from the ends of the protective case.
b. Remove the plastic packing material from the lamp.
c. Remove the cathode nut from the lamp before removing it from the case.
d. Hold the anode end of the new lamp in your left hand and angle it up through the hole in 
the back of the reflector assembly. 
e. Insert your...

   Installation and Setup
CP2215 User Manual10020-101225-01 Rev. 1 (01-2014)
f. Hand-tighten the cathode nut (E). Make sure the smooth portion of the nut is against the 
cathode clamp.
g. Tighten the cathode screw (D) with a hex key.
h. Align the ring terminal on the anode wire (B) with the mounting position, ensuring the 
crimped side of the wire is facing out. 
i. Tighten the anode screw. 
j. Route the anode lead away from nearby metal surfaces.
9. Close the lamp access door and tighten the 2...

   Installation and Setup
CP2215 User Manual11020-101225-01 Rev. 1 (01-2014)
B• SOFTST - (Software State) Indicates the state of the software application running on the 
ICP. During normal operation, this LED blinks. During start up, the LED changes from off to 
blinking.
• OSST - (Operating System State) Indicates the state of the ICP operating system. During 
normal operation, the LED is green. During start up, the LED changes from off to green.
• FMTST - (FMT FPGA State) Indicates the state of the FMT...

   Installation and Setup
CP2215 User Manual12020-101225-01 Rev. 1 (01-2014)
Connect the Projector to a Computer
Connect one end of an Ethernet or a RS232 cable to the Ethernet or the RS232 PIB port on the 
projector communications panel and the other end to your computer. To communicate with the 
projector, the projector must be added to the same network as the computer. See Add the Projector 
to a Network on page 16.
Connect Devices to the 3D Terminal
See View 3D Content on page 65.
Connect Devices to...