Christie Digital Systems Cp2215 Quick Start Guide

   Maintenance
CP2215 Quick Start Guide27020-101295-01 Rev. 1 (11-2013)
Inspect the Card Cage Filter
Use only high efficiency Christie approved filters. Never operate the projector without the filter 
installed.
You should check the condition of the card cage air 
filter monthly. Clean or replace the card cage air 
filter sooner if you are operating the projector in a 
dusty or dirty environment. The filter is located on 
the left side of the projector behind the air filter 
cover. 
1. Loosen the 2...

   Maintenance
CP2215 Quick Start Guide28020-101295-01 Rev. 1 (11-2013)
4. Rinse the filter thoroughly by holding it on an angle under cool running water. The air flow 
arrow on the side of the filter should face down.
5. Repeat steps 3 and 4 if the filter still appears dirty.
6. Shake the filter over a container until most of the water is removed.
7. Place the filter on its edge on a flat, stable surface and allow it to dry thoroughly.
8. To confirm that the filter is dry, place it over a dry paper...

CP2215 Quick Start Guide29020-101295-01 Rev. 1 (11-2013)
Specifications
This section provides detailed specifications for the Christie CP2215 projector. Due to continuing 
research, specifications are subject to change without notice.
Power Requirements
AC Input (A)
Below 200VAC, when the lamp is ignited, a 25 A input surge current might occur for three seconds.
UPS AC Input (B)
ItemDescription
Circuit Breaker 20A
Voltage Range 200 - 240 VAC
Line Frequency 50 Hz - 60 Hz nominal
Inrush Current 

   Specifications
CP2215 Quick Start Guide30020-101295-01 Rev. 1 (11-2013)
Lamp
The ballast is power regulated and has a maximum current of 97A. Therefore the maximum power 
specification for a given lamp may not be achievable until the lamp has aged, since lamp voltage 
increases with hours of use.
Projectors typically force a 10 minute cool down period. Make sure you do not re-strike the lamp 
any sooner than 2 minutes into this cool down period since hot re-strikes reduce lamp life.
Physical...

   Specifications
CP2215 Quick Start Guide31020-101295-01 Rev. 1 (11-2013)
Regulatory
This product conforms to the following regulations related to product safety, environmental 
requirements and electromagnetic compatibility (EMC).
Safety
• CAN/CSA C22.2 No. 60950
• UL 60950
• IEC 60950-1
• EN60950
Electro-Magnetic Compatibility
Environmental
• EU Directive (2011/65/EU) on the restriction of the uses of certain hazardous substances 
(RoHS) in electrical and electronic equipment and the applicable...

   Specifications
CP2215 Quick Start Guide32020-101295-01 Rev. 1 (11-2013)
Environment
Operating Environment
Non-Operating Environment
ItemDescription
Temperature 10°C to 35°C (50°F to 95°F)
Humidity (non-condensing) 20% to 80%
Altitude 0 - 3000 meters
Maximum ambient temperature 35°C
ItemDescription
Temperature -25°C to 65°C (-13°F to 149°F)
Humidity (non-condensing) 0% to 95% 

   Specifications
CP2215 Quick Start Guide33020-101295-01 Rev. 1 (11-2013)
Accessories
Standard (sold with product)
• Touch panel controller (TPC) with interface cable
• Set up guide
• Interconnect diagram
• Power cord
 Optional Accessories
ItemDescription/Part Number
Zoom Lenses • 1.2-1.75” DLPCine Zoom (108-350109-01-XX)
• 1.3-1.75” DLPCine Zoom (108-320106-XX)
• 1.39-1.9” DLPCine Zoom (108-327103-XX)
• 1.5-2.2” DLPCine Zoom (108-329105-XX)
• 1.75-2.4” DLPCine Zoom (108-321107-XX)
• 1.9-3.0” DLPCine...

For the most current technical documentation, please visit  www.christiedigital.com 
United Kingdom
ph: +44  (0) 118 977 8000United Arab Emirates
ph: +971 4 3206688 Spain
ph: + 34 91 633 9990Singapore
ph: +65 6877-8737
Republic of South Africa
ph: +27 (0)11 510 0094 Korea (Seoul)
ph: +82 2 702 1601Japan (Tokyo)
ph: 81 3 3599 7481 India
ph: +91 (080) 6708 9999
Germany
ph: +49 2161 664540 France
ph: +33 (0) 1 41 21 44 04 Eastern Europe and
Russian Federation
ph: +36 (0) 1 47 48 100
China (Shanghai)
ph: +86...