Christie Digital Systems Cp2215 Quick Start Guide

   Installation and Setup
CP2215 Quick Start Guide7020-101295-01 Rev. 1 (11-2013)
Install the Lens
The lens seals the projection head, preventing contaminants from entering the main electronics 
area. Do not operate the projector without a lens installed. Install a lens plug when you install or 
transport the projector.
1. Move the lens clamp on the front of the projector to the open position.
2. Position the lens so the lens retaining ring mounts align with the lens mount. 
3. Remove the lens caps from...

   Installation and Setup
CP2215 Quick Start Guide8020-101295-01 Rev. 1 (11-2013)
6. Move the lens clamp to the locked position. 
Install the Lamp
1. If the projector is operating, turn it off and allow it to cool a minimum of 15 minutes.
2. Turn the breaker switch for the projector off.
3. Disconnect the projector from AC power.
4. Put on your protective clothing, face shield, and gloves.
5. Insert the key in the lamp door lock, turn the key, and open the lamp door. 
6. Loosen the 2 thumbscrews (A and...

   Installation and Setup
CP2215 Quick Start Guide9020-101295-01 Rev. 1 (11-2013)
7. Loosen the cathode screw (D) with the 5 mm hex key attached to the lamp door.
8. Install the lamp:
a. Remove the tape from the ends of the protective case.
b. Remove the plastic packing material from the lamp.
c. Remove the cathode nut from the lamp before removing it from the case.
d. Hold the anode end of the new lamp in your left hand and angle it up through the hole in 
the back of the reflector assembly. 
e. Insert...

   Installation and Setup
CP2215 Quick Start Guide10020-101295-01 Rev. 1 (11-2013)
f. Hand-tighten the cathode nut (E). Make sure the smooth portion of the nut is against the 
cathode clamp.
g. Tighten the cathode screw (D) with a hex key.
h. Align the ring terminal on the anode wire (B) with the mounting position, ensuring the 
crimped side of the wire is facing out. 
i. Tighten the anode screw. 
j. Route the anode lead away from nearby metal surfaces.
9. Close the lamp access door and tighten the 2...

   Installation and Setup
CP2215 Quick Start Guide11020-101295-01 Rev. 1 (11-2013)
B• SOFTST - (Software State) Indicates the state of the software application running on the 
ICP. During normal operation, this LED blinks. During start up, the LED changes from off to 
blinking.
• OSST - (Operating System State) Indicates the state of the ICP operating system. During 
normal operation, the LED is green. During start up, the LED changes from off to green.
• FMTST - (FMT FPGA State) Indicates the state of...

   Installation and Setup
CP2215 Quick Start Guide12020-101295-01 Rev. 1 (11-2013)
Connect the Projector to a Computer
Connect one end of an Ethernet or a RS232 cable to the Ethernet or the RS232 PIB port on the 
projector communications panel and the other end to your computer. To communicate with the 
projector, the projector must be added to the same network as the computer. See Add the Projector 
to a Network on page 16.
Connect Devices to the 3D Terminal
See View 3D Content on page 65.
Connect...

   Installation and Setup
CP2215 Quick Start Guide13020-101295-01 Rev. 1 (11-2013)
This diagram illustrates how to wire a GPIO cable to a server or a 3D device:
The recommended operating point is 5mA, the maximum current is 50 mA, and the forward voltage 
drop is 
~ 1 V (@ 5 mA).
Connect Devices to the SCCI Port
The Simple Contact Closure Port (SCCI) port is a DB-9 (male) connector located on the PIB input 
panel. The SCCI port controls a limited set of projector functionality through contact closures....

   Installation and Setup
CP2215 Quick Start Guide14020-101295-01 Rev. 1 (11-2013)
All SCCI inputs require a pulse input of 50ms to several seconds to operate reliably. Inputs are 5V 
resistor current limited LED’s inside of optocouplers.
The open-collector Health Output (PIN 8) circuit only draws power when a failure occurs or an 
interlock is activated.
Connect Power
1. If the projector is operating, turn it off and disconnect it from AC power.
2. Loosen the threaded bolt on the ground lug on the AC...

   Installation and Setup
CP2215 Quick Start Guide15020-101295-01 Rev. 1 (11-2013)
4. Insert a bare end of the protected earth wire into the hole on the top of the ground lug so it is 
beneath the threaded bolt.
5. Tighten the threaded bolt to 50 in-lb.
6. Connect the other bare end of the protected earth wire to the building ground.
7. Connect one end of the projector power cord to the AC receptacle on the lower-left rear corner 
of the projector and then connect the other end of the power cord to an AC...

   Installation and Setup
CP2215 Quick Start Guide16020-101295-01 Rev. 1 (11-2013)
Activate Marriage
You must complete marriage to display encrypted content and to comply with the Digital Cinema 
Initiatives (DCI) specification.  You cannot complete marriage remotely. In addition, an authorized 
employee must be physically present to verify that the anti-tamper seal on the firewall is unbroken, 
the projector is unaltered,   and to press the marriage button on the card cage faceplate.
1. Log on to the...