Christie Digital Systems Cp2215 Quick Start Guide

CP2215
Quick Start Guide
020-101295-01 

NOTICES 
COPYRIGHT AND TRADEMARKS © 2013 Christie Digital Systems USA Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.
REGULATORYThe product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC 
Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a 
commercial environment. The...

CP2215 Quick Start Guidei020-101295-01 Rev. 1 (11-2013)
Table of Contents
Installation and Setup............................................1
Safety Precautions   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1
AC/Power Precautions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2
Power Cords and Attachments   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2
Lamp Precautions  . . . . . . . . . ....

   
CP2215 Quick Start Guideii020-101295-01 Rev. 1 (11-2013)
Inspect and Clean Optics  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Clean the Lens  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Replace the Lamp  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
 Remove the Existing Lamp  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24...

CP2215 Quick Start Guide1020-101295-01 Rev. 1 (11-2013)
Installation and Setup
This manual is intended for professionally trained operators of Christie high-brightness projection 
systems. These operators are qualified to replace the lamp and air filter, but should not attempt to 
install or service the projector.
Only accredited Christie technicians who are knowledgeable about the hazards associated with 
high-voltage, ultraviolet exposure, and the high temperatures generated by the projector lamp are...

   Installation and Setup
CP2215 Quick Start Guide2020-101295-01 Rev. 1 (11-2013)
AC/Power Precautions
Power Cords and Attachments
• Use only the AC power cord that is provided with the projector. DO NOT attempt operation 
if the AC supply is not within the specified voltage and power range. Failure to comply 
could result in death or serious injury. 
• As a safety feature the projector is equipped with a three-wire plug with a third 
(grounding) pin. If you are unable to insert the plug into the outlet,...

   Installation and Setup
CP2215 Quick Start Guide3020-101295-01 Rev. 1 (11-2013)
Lamp Precautions
Projector Components - Front
• EXPLOSION HAZARD! Wear authorized protective safety gear whenever the lamp door is 
open! Never attempt to remove the lamp directly after use. The lamp is under significant 
pressure when hot and cold, and may explode, causing personal injury and/or property 
damage. Failure to comply results in death or serious injury.
• Any lamp used in the projector is under high pressure...

   Installation and Setup
CP2215 Quick Start Guide4020-101295-01 Rev. 1 (11-2013)
Projector Components - Rear
Position the Projector
1. If you are installing the projector in the optional rack stand (P/N 108-416102-XX) follow the 
instructions provided with the rack stand to install it.
2. Position the projector so it is centered and parallel with the theatre screen. If space is limited, 
aim the projector slightly off-center and use lens offset to center the image on the screen. 
D Air Filter Cover and...

   Installation and Setup
CP2215 Quick Start Guide5020-101295-01 Rev. 1 (11-2013)
Adjust Tilt and Level the Projector
The front-to-back and side-to-side tilt of the projector must not exceed 15 degrees. 
1. Loosen the lock nut with a 3/4 in. or 19mm wrench. 
2. Turn the adjustable feet on the bottom of the projector 
clockwise or counter-clockwise 1/8th of a turn at a time to 
move the projector up or down.
When adjusting two or more feet at once, always adjust 
them the same amount. This keeps equal...

   Installation and Setup
CP2215 Quick Start Guide6020-101295-01 Rev. 1 (11-2013)
3. Tighten the mounting arm until it fits tightly on the ball joint. 
4. Connect the cable from the TPC to the connector located on the projector rear panel.
5. Tilt the TPC to adjust the viewing angle.
Connect the Exhaust Duct
You must install the optional duct (P/N: 119-103105-xx) if an air volume of 9,000 BTU (per hour) 
cannot be ventilated from the room in which the projector is installed.
When using an external duct,...