Christie Digital Systems Cp2215 Quick Start Guide

   Installation and Setup
CP2215 Quick Start Guide17020-101295-01 Rev. 1 (11-2013)
Add the Lamp Information to the Lamp History
1. If the lamp is on, tap the lamp off ( ) icon to turn it off.
2. Tap Menu > Advanced Setup > Lamp Change Wizard.
3. Tap Next.
4. Complete these fields:
5. Tap Save.
6. Tap Next.
Turn the Lamp On
On the projector touch panel controller (TPC) main screen, tap the lamp on ( ) icon.
Align the Lamp with LampLOC
To ensure optimal lamp performance and peak brightness at the screen...

   Installation and Setup
CP2215 Quick Start Guide18020-101295-01 Rev. 1 (11-2013)
2. Tap Menu > Advanced Setup > LampLOC Setup.
3. Tap Display Full Screen White Test Pattern.
4. Tap Do Auto.
Adjust the Image to Fit Your Screen
This procedure must be completed before you complete a boresight adjustment. 
1. Verify the projector is properly positioned relative to the screen. 
See Position the Projector on page 4.
2. Display a RGB-12bit-Full Screen White test pattern and center the image:
a. Tap the Test...

   Installation and Setup
CP2215 Quick Start Guide19020-101295-01 Rev. 1 (11-2013)
8. Display a full white test pattern:
a. On the TPC, tap the Test Pattern icon ( ) in the task bar.
b. Tap All Test Patterns.
c. Tap RGB-12bit-Full Screen White.
9. If the test pattern is focused and centered on the screen you do not need to complete further 
image adjustment. 
If the image is not focused and centered on the screen, complete one of these procedures:
a. If the image appears distorted and resembles a...

CP2215 Quick Start Guide20020-101295-01 Rev. 1 (11-2013)
Maintenance
This section provides information and procedures for performing projector maintenance. You should 
read through this section in its entirety before performing maintenance activities. When you 
perform projector maintenance, obey all warnings and precautions.
Inspect Ventilation
Vents and louvers in the projector covers provide ventilation, both for intake and exhaust. Never 
block or cover these openings. Do not install the projector...

   Maintenance
CP2215 Quick Start Guide21020-101295-01 Rev. 1 (11-2013)
Clean the Radiator Filter
1. Tap and hold the red power button   on the TPC Main panel to turn the lamp and projector 
off. 
2. Allow the lamp to cool for a minimum of 15 minutes.
3.
Unplug the projector.
4. Remove the top lid.
5. Reach into the projector and then loosen the first service panel screw.
6. Open the integrator rod access door and loosen the second service panel screw. 

   Maintenance
CP2215 Quick Start Guide22020-101295-01 Rev. 1 (11-2013)
7. Push the clips on the top of the service panel down and out to remove the service panel.
8. Loosen the thumbscrew securing the radiator filter door.
9. Pull the filter up and out and then wash the radiator filter with water and a mild detergent or 
clean it with compressed air.
10. When the filter is completely dry, reinstall it and then install the service panel and top lid.
Inspect the Lamp
• Check the contact surfaces of the...

   Maintenance
CP2215 Quick Start Guide23020-101295-01 Rev. 1 (11-2013)
• For the lens only - lens cleaning solution such as Melles Griot Optics Cleaning Fluid 18LAB011 or 
equivalent
• Cotton swabs with wooden stems.
• Lens cleaning cloth or microfiber such as Melles Griot 18LAB024 or equivalent.
Clean the Lens
A small amount of dust or dirt on the lens has minimal effect on image quality-to avoid the risk of 
scratching the lens, clean the lens only if absolutely required. 
Remove Dust
1. Brush most of...

   Maintenance
CP2215 Quick Start Guide24020-101295-01 Rev. 1 (11-2013)
Remove the Existing Lamp
1. Tap and hold the red power button   on the TPC Main panel to turn the lamp and projector 
off. 
2. Allow the lamp to cool for a minimum of 15 minutes.
3.
Unplug the projector.
4. Put on your protective clothing and face shield.
5. Insert the key in the lock on the lamp door, turn the key, and then open the lamp door. Do not 
place heavy objects on the open lamp door.
6. Loosen the two thumbscrews (A and B)...

   Maintenance
CP2215 Quick Start Guide25020-101295-01 Rev. 1 (11-2013)
g. With the lamp removed, visually inspect the reflector and clean if necessary.
8. Remove the new lamp from the protective case.
9. Loosen the cathode screw and remove the cathode nut from the lamp.
Install the New Lamp
1. Remove the tape from the ends of the protective case.
2. Remove the plastic packing material from the lamp.
3. Remove the cathode nut from the lamp before removing it from the case.
4. Hold the anode end of the...

   Maintenance
CP2215 Quick Start Guide26020-101295-01 Rev. 1 (11-2013)
the reflector and guide the lamp onto the cathode clamp. Be careful not to hit the lamp against 
the reflector.
5. Thread on and hand-tighten the cathode nut. Make sure the smooth portion of the nut is 
against the cathode clamp.
6. Tighten the cathode clamp (F) with a hex key.
7. Align the ring terminal on the anode wire (B) with the mounting position ensuring the crimped 
side of the wire is facing out. Tighten the anode screw....