Casio Qt 6100 Service Manual

— 69 —
ActionMeaningPrompt message
E140  Wrong menu.
E141  Press  
twice before finalization.
E145  Arrangement syntax er-
ror.
E150  Incorrect value entry.
E151  Incorrect Key Pressed.
E152  PGM File or Memory 
number does not Exist.
E164  Employee No. is not 
Found in the Employee 
File.
E165  Employee No. is not 
Clocking-in.
E166  Employee No. is Occu-
pied.
E167  Incorrect Job code.
E168  Your Operation is out of 
Schedule.
  Please Call Manager.
E169  Work Hours Exceeded.
  Please Call Manager....

— 70 —
ActionMeaningPrompt message
E200  Insert CF Card.
E201  Format error.
E203  Insufficient memory.
E205  The file already exists.
  Do you replace?
  YES:Replace the file.
  NO :Input new name.
E240  Customer No. is occu-
pied.
E241  Customer memory full.
E242  Customer not found.
E243  Illegal Site ID.
E244  Credit limit over.
E251  Magnetic card error.
E252  Enter customer name.
E253  Enter address.
E254  Enter phone number.
CF card is not inserted to the slot.
CF card data or formats illegal....

— 71 —
Data cannot be printed out.
Backup to R/J printer?
Do you want to clear data?
Cancel OK?
Please wait.
Item Consolidation Mode
Non Consolidation Mode
REG Mode
REFUND Mode
REG- Mode
Training
REG2 Mode
Please Sign on.
Enter Check/Table Number.
Enter Table Number.
Enter Number of covers.
Enter Seat Number.
Perform Slip Printing.
Issue Guest Receipt.
Perform Validation Printing.
Perform Check Printing.
Perform Check Endorsement.
Operation Code?
Re_configuration...
Re_configuration end
Clock-in OK?...

— 72 —
9-3  System error code
All error codes are contained in the list below. These error codes are displayed or printed on error log 
report.
  Error code Meaning
  0010  Handler access error (software)
  0011  Cannot execute handler (system configuration)
  0012  Break by PC
  0013  Break by ECR
  0014  DSR off before receiving command packet
  0015  Receive illegal command number of command packet
  0016  Receive illegal character
  0017  Send error (hardware)
  0018  Receive error (hardware)
  0019...

— 73 —
  0079  Z lock release error on satellite terminal
  0081  Check tracking master is removed from system.
  0082  Check tracking backup master is removed from system.
  0128  Parameter error / Maximum length of send error
  0130  Error drive
  0134  Network parameter error
  0138  Detect error in core system
  0140  Parameter error (record length exceeds work buffer)
  0141  EOF over
  0144  Calculation overflow
  0145  Undefined value of n_open () mode
  0146  Mismatch of type when closing network...

— 74 —
9-4. OS Fatal Error
When a fatal error occurs during an operation of the operating system, normal operation becomes im-
possible afterwards.
Therefore, the OS displays a message as shown below and stops the operation of ECR.
Such errors include errors of the OS (ITRON) itself, driver system errors, etc.
The values of Error No. and Error Code vary according to errors.
*  These are intentional system halting errors to prevent a system runaway due to software. Types 
of errors may be increased in...

— 75 —
 Description of Errors
(1) Semaphore acquisition error
Error No. -1 / -4 / -6
Description of phenomenon:
This is a system error in ITRON.
This phenomenon may occur when the exclusion function of ITRON is used.
Possible causes:
A software bug or an illegal operation of ITRON.
(2) Mailbox creation error
Error No. -2 / -3 / -5 / -7 / -21
Description of phenomenon:
This is a system error in ITRON.
This phenomenon may occur when a function of ITRON called Mailbox is used.
Possible causes:
A software...

— 76 —
 error point:
  Indicates  the  point  on  the  memory  where  the  operation  instruction  that  causes  the  above  general 
exception is located (program counter).
  However, an illegal address may be displayed depending on the exception code.
 access adrs:
  Indicates the address that is accessed according to the operation instruction that causes the above 
general exception.
  However, the address is 0 (zero) and has no meaning if the access is not the cause.
 Error Code Correspondence...

— 77 —
(8) error no. 180: Reservation instruction code exception
(9) error no. 1A0: Slot illegal instruction exception
Description of phenomenon:
These exceptions occur when an illegal instruction is performed.
Possible causes:
It is hard to think that this phenomenon is caused by software, because these errors 
occur due to an internal operation of the CPU.
This  phenomenon  is  apt  to  occur  when  backup  of  RAM  is  not  performed  normally 
and the memory has been changed.
It is possible that the...

— 78 —
10. IC DATA
■ MAIN PCB (E820-1 PCB)
  1.  ALVCH16244 (IC13, 17)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
1OE
1Y1
1Y2
GND
1Y3
1Y4
VCC2Y1
2Y2
GND
2Y3
2Y4
3Y1
3Y2
GND
3Y3
3Y4
VCC4Y1
4Y2
GND
4Y3
4Y4
4OE
2OE
1A1
1A2
GND
1A3
1A4
VCC2A1
2A2
GND
2A3
2A4
3A1
3A2
GND
3A3
3A4
VCC4A1
4A2
GND
4A3
4A4
3OE
1OE
1A1
1A2
1A3
1A41Y1
1Y2
1Y3
1Y4
1
47
46
44
43
2
3
5
6
2OE
2A1
2A2
2A3
2A42Y1
2Y2
2Y3
2Y4
48
41
40
38
37
8
9
11...