Casio Projector XJ-V1 User Manual

21
Screen Settings 3 
No Signal ScreenSelect one of the following as the projection image whenever there is no input signal 
being input to the projector: “Blue”* (blue screen), “Black” (black screen), “Logo” 
(projector built-in logo).
Screen Settings 3
Blank ScreenSelect one of the following as the projection image whenever the [BLANK] key is 
pressed: “Blue”* (blue screen), “Black” (black screen), “Logo” (projector built-in 
logo).
Screen Settings3 
Restore Menu DefaultsReturn all of the items in the...

22
Option Settings 23 
Timer FunctionDisplay the timer function menu. For details, see “Using the Presentation Timer 
(TIMER)” (page 16).
Option Settings 23 
Restore Menu DefaultsReturn all of the items in the “Option Settings 2” main menu to their initial defaults for 
the currently projecting image source.
Operational Info (RCHD) Display the projector information below.
Input Signal, Signal Name, Resolution, Horizontal Frequency, Vertical Frequency, 
Scan System, Light Time, Version (projector ROM...

23
The password feature lets you keep unauthorized individuals from using the projector. You can specify 
whether password input is required whenever you turn on the projector, and you can specify and 
change the password as required. Use the Setup Menu “Option Settings 1 3 Password” setting to 
configure password settings.
Using the Password Feature
Note the following precautions whenever you use the password feature.
zThe password feature protects against unauthorized use of the projector. Note that it...

24
To change the password
1.Press the [MENU] key to display the setup menu.
2.Use the [T] key to select “Option Settings 1”, and then press the [ENTER] key.
3.Use the [T] key to select “Password”, and then press the [ENTER] key.
zThis will display a dialog box prompting you to enter the current password.
4.Enter the current password.
zThe password of your projector is not really a “word” made up of letters, but rather a 
sequence of remote controller key inputs.
zIf the projector is still protected by...

25
To change the power on password setting
1.Perform steps 1 through 5 under “To change the password” (page 24) and 
display the Power On Password setting screen.
2.After confirming that “Power On Password” is selected, use the [W] and [X] keys 
to select either the “On” or “Off” setting.
zChanging the setting from “Off” to “On” will cause the “Prompt for password when power is 
turned on?” dialog box to appear. Press the [ENTER] key to confirm that you want to turn on 
power on password protection, or...

26
Cleaning the Projector
Make it a habit to clean the projector at regular intervals as described in this section. Before cleaning 
the projector, be sure to unplug it from the power outlet and make sure it is cooled down completely.
Wipe the exterior of the projector with a soft cloth that has been moistened in a weak solution of water 
and a mild neutral detergent. Be sure to wring all excess moisture from the cloth before wiping.
Never use benzene, alcohol, thinner, or any other volatile agent for...

27
Troubleshooting
The POWER/STANDBY indicator and STATUS indicator change to show the current status of the 
projector as described in the tables below.
POWER/STANDBY indicator
STATUS indicator
NotezThe POWER/STANDBY and STATUS indicators both light amber immediately after the 
projector is plugged into a power outlet.
Indicators
When the indicator is doing this:It means this about the projector:
Lit red Connected to a power source, but turned off (standby mode)
Flashing green Warming up after being...

28
Warning messages and indicators let you know what the problem is when a projector error occurs.
zWhen an error occurs, wait until the fan stops before unplugging the AC power cord. If you unplug 
the AC power cord while the fan is still operating, an error may occur when you plug the AC power 
cord back in.
zPress the [ESC] key to clear the warning message.
Error Indicators and Warning Messages
Indicator/Error MessageDescription and Required Action
POWER : Green steady The projector’s internal...

29
POWER : Red steady The projector was turned off automatically because the light source unit 
turned off or did not turn on. After confirming that the POWER/STANDBY 
indicator is lit red (without flashing), unplug the power cord. Wait for a 
short while and then plug it back in and turn on the projector again.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. STATUS : Red flashing 
(0.5-second interval)
Message : –
POWER : Red...

30
Check the following items whenever you experience any problem with the projector.
Projector Troubleshooting
ProblemCause and Recommended Action
Power does not turn on.zIf the POWER/STANDBY indicator is not lit, the AC power cord is not connected 
correctly. Connect the AC power cord correctly.
zIf the POWER/STANDBY indicator is lit red and the STATUS indicator is lit (or 
flashing) red or amber, it means some type of error has occurred. See “Error 
Indicators and Warning Messages” (page 28).
No image...