Casio Projector XJ-V1 User Manual

1
DATA PROJECTOR
XJ-V1
User’s Guide
zBe sure to read the “Safety Precautions” and “Operating Precautions” in the “Setup Guide” 
document, and make sure you use this product correctly.
zKeep this manual in a safe place for future reference.
zVisit the site below for the latest version of this manual and the “Setup Guide”.
http://world.casio.com/manual/projector/EN 

2
zDLP is a registered trademark of Texas Instruments of the United States.
zHDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered 
trademarks of HDMI Licensing, LLC.
zXGA is a registered trademark of IBM Corporation of the United States.
zOther company and product names may be registered product names or trademarks of their 
respective owners.
zThe contents of this User’s Guide are subject to change without notice.
zCopying of this manual, either in part or its...

3
Contents
Useful Features and Functions ...................................... 5
Getting Ready .................................................................. 6
Setting Up the Projector .........................................................................6
Setup Precautions ....................................................................................................... 6
Connecting Projector Cables .................................................................7
Remote Controller...

4
Using the Setup Menu (MENU) ............................................................19
Basic Setup Menu Operations ................................................................................... 19
Setup Menu Settings ................................................................................................. 19
Password Protection ............................................................................23
Using the Password...

5
Useful Features and Functions
zMercury-free Hybrid Light Source
A CASIO-original laser and LED hybr id light source delivers high luminance up to 2,700 lumens. This 
projector does not use a mercury lamp,  making it environmentally friendly.
z No-wait Projection
A CASIO hybrid light source reaches maximum brightness immediately after power is turned on, 
compared with a wait of approximately one minute normally required with a mercury lamp. The light 
source will even reach maximum brightness...

6
Getting Ready
This section explains how to select a location for the projector, how to connect its cables, and how to 
perform other operations required before using it.
Locate the projector on a desk, table, or stand that is firm and level. Make sure that you allow 
sufficient space around the sides and back of the projector for proper ventilation. The illustrations 
below show how the projector should be oriented relative to the screen for optimum projection.
Setup Precautions
zUse a conveniently...

7
Connect the projector to a power outlet and to an input source device.
NotezFor more information about component video connection, see “Connecting to a Component 
Video Output” on page 32.
z For information about how to co nnect for RS-232C control of the projector, see “Projector 
RS-232C Control” (page 39).
z For information about how to connect in order to update the projector firmware, see 
“Updating Firmware” (page 33).
Connecting Projector Cables
Use an RGB cable to connect to the RGB output...

8
Projector operations are performed using the remote controller that comes with it. Point the remote 
controller signal emitter at one of the signal receivers on the projector as you perform remote 
controller key operations. The maximum range of the remote controller signal is approximately 
5 meters (16.4 feet) (between signal emitter and receiver).
Important!zTo avoid running down the battery, store the remote control unit so its keys are not pressed 
inadvertently.
Remote Controller
1Remote control...

9
To load remote controller batteries
Important!zBe sure to use alkaline batteries only.
To replace remote controller batteries
Open the battery cover on the back of the remote controller, replace the old batteries with new ones, 
and then close the battery cover.
*CautionRISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
1.Open the battery cover on the back 
of the remote controller.2.Load two new batteries into the 
case, making sure...

10
Operating the Projector
This section explains how to use the remote controller to perform projector operations.
To select the input source
1.Press the [INPUT] key.
2.On the “Input” dialog box that appears, use the [INPUT], [S] and [T] keys to 
select the input source you want and then press the [ENTER] key.
zIf you do not press the [ENTER] key, the projector will automatically apply the currently 
selected input source after about two seconds.
zThe name of the input source you selected will appear in...